Search Documents

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By P. R. ZETTWOOG

HISTORICAL BACKGROUND A program in France to develop personal [a] dosimeters has been initiated 1974. The patent on which is based the present device was obtained in 1972 * . From 1972 to 1974, the possibilities of applying certain ionograph track detectors to the spectrodosimetry of radon daughters was explored. The first prototype were produced in 1974. It took four years (from 1974 to 1978) to produce an autonomous dosimeter whose components has a sufficient life span, especially for the turbine motor unit. Qualification in the laboratory was obtained in 1977. In 1978 it was obtained in the mine for technology (autonomy of 12 hours and a life span of more than one year) and in 1980 for monitoring. 300 dosimeters have been tested in underground mines all together. Indispensable peripheral equipment were also developed from 1976 to 1980 : calibration devices, equipment to prepare and develop the films, read out systems. The concept of an "Integrated System of Individual Dosimetry" (ISID) based on a personal [a] dosimeter measuring exposure to radon daughters, thoron daughters, ore dust and external irradiation doses was proposed at the end of 1980. Since January 1st 1981, ISID is used on a routine basis in some french mines, situated in remote area, and appears to be very competitive with the ambiant dosimetry. The latest version of the dosimeter is produced in mass series since June 1981 and should equip all french mines in 1982. DESCRIPTION OF THE INSTRUMENTATION DEVELOPMENT OF THE DOSIMETER MEASURING HEAD The measuring head is based on the use of ionographic film to detect a tracks. In fact, the measuring head is a spectrodosimeter which measures separately over the period of exposure: - the potential [a] energy inhaled due to the decay of Po 218, Po 214, and Po 212 ; - the number of Rn 222 atoms inhaled ; - the inhaled total [a] activity of the five long-lived emitters present in the ore dust. The contribution to the total inhalable potential [a] energy of these various radionuclidesin a typical underground mine is studied in Appendix I. The measuring head described in detail in Appendix II, is able to satisfy all the implications made in the ICRP recommendations. Appendix III deals with the use of this measuring head in the cases where the equilibrium factor is lower than 0.1. This situation occur in open-pit mines where account must be taken of the Rn 222 contribution, which is no longer negligible in relation to that of its daughters. CURRENT DOSIMETER PERFORMANCES Table I shows the characteristics of the latest dosimeter. Appendix IV should be consulted concerning qualification of the dosimeter in the laboratory and in mines, technological development which finally produced the [a] dosimeter and its peripheral equipment, and technical presentation of the ISID (Integrated System of Individual Dosimetry) based on the concept of a multirisk personal dosimeter. Data on the installation and operating costs of such a dosimeter, which would seem to be competitive, are also given in this Appendix. ADVANTAGES OF PERSONAL DOSIMETRY AS COMPARED TO AREA MONITORING The results of the first eight months of experiments carried out under real conditions in an underground mine site are given in detail in reference 8. Area monitoring : The monthly exposure per worker to inhaled Rn 222 was determined from the knowledge of time spent in various areas of the mine and for the different mining operations, as well as from numerous and systematic sampling of the Rn 222 concentration in all work places. Personal dosimetry : The exposure to potential energy from radon daughters was measured by an [a] dosimeter developed by the CEA and worn by each of the 160 miners during eight months. In this way 160 x 8 pairs of monthly individual exposure values have been obtained which can be statistically studied. This test was decisive for us because it proved that the [a] dosimeter was technically sound (very few defects over one year for 160 dosimeters) and especially that personal monitoring devices were superior to area monitoring devices. The following conclusions can be drawn 1. The exposure distribution obtained by personal dosimetry is log-normal. This is true for the results on the whole as well as for groups of results relating to certain explanatory variables. See fig. la, 1b, 1c. 2. The exposure distribution obtained by area monitoring does not correspond to any type of distribution. If the results of personal monitoring are taken as a reference, area monitoring tends to underestimate the high exposures and overestimate the low exposures.See fig. 2. 3. [a]-energy exposures are underestimated when calculated from radon exposures and the equilibrium factor found in the considered mines. This is due to episodes or to zones of high radon concentrations not registered

Jan 1, 1981

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By D. W. H. Su

"This paper presents the results of a comprehensive study conducted by CONSOL Energy, Marcellus Shale Coalition, and Pennsylvania Coal Association to evaluate the effects of longwall-induced subsurface deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall abutment pillar can maintain mechanical integrity during and after mining operations. A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar were mined by. To evaluate the resulting coal protection casing profile and lateral displacement, three separate 60-arm caliper surveys were conducted. Prior to the longwall panels being mined by, a number of 3D finite element simulations were conducted to estimate subsidence at the surface, coal pillar pressure increases, the resulting coal protection casing profile and displacement, and the vertical and horizontal displacements in the four monitoring wells. Comparisons of the pre-mining 3D finite element simulation results and the surface/subsurface/underground instrumentation results show that the measured test well and IPI casing deformations and profiles are in reasonable agreement with those predicted by the 3D finite element models, and that the measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models, which serves to validate the 3D finite element models. Parametric studies employing the validated 3D finite element models demonstrate that larger coal protection casing thickness is expected to have little effect on the lateral deformation, although it may reduce the magnitude of casing plastic deformation, and under deeper cover (~1,100 feet), lateral casing deformation is expected to be smaller, although larger plastic casing deformation may be present near the seam level. Also, evaluation of various casing and cementing designs using the validated 3D models clearly indicates that, when all casings are grouted to the surface except the intermediate and production casings, the intermediate and production casings show little deformation and no plastic strain. This research represents a very important step and initiative to utilize the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the oil and gas industries"

Jan 1, 2017

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

By G. A. Campbell

Mining companies have been very interested in the presence of a number of small but high-grade ore bodies of base metals in northern Wisconsin and the west/central section of the Upper Peninsula (UP) of Michigan. The region is rural with outdoor recreation/tourism and lumbering being the key industries. The economy of the region is based on the use of its natural resources, and mining is not a new activity to the region, especially the UP. The western UP was historically a key mining district for copper and iron, and today the central UP has a significant iron-mining district. However, all efforts to develop the base metal ore bodies have been met with a storm of controversy involving the local community, regional activists, Native Americans, and the state government, and only one mine has gone into operation. There is concern by some stakeholders about the sustainability of mining in communities that depend on the environment for tourism, recreation, and other commercial activities. There have been four attempts to get the necessary approvals to mine in this region: the successful Flambeau Mine effort (Wisconsin), the failed Crandon project (Wisconsin) and Lynne project (Wisconsin) efforts, and the continuing effort to get the Eagle Project (UP of Michigan) approved. The cases are presented to illustrate the project situation, the history of the permitting effort, and the opposing parties and their concerns. The case of the Eagle Project is looked at in detail by using the method of discourse communities and discourse analysis. Results of the analysis provide insight into the communication efforts to address community concerns about sustainability and what more can be done to improve this dialogue.

Jan 1, 2008

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

By T. J. Crebs

The latest estimates compiled by the Society of Exploration Geophysicists again indicate a moderate increase in mining geophysical activity in 1980 over the 1979 level. While North American activity remained at above the 1979 level, a considerable increase in mining geophysics was reported in South America, Australia, and the Far East. The total worldwide expenditures for mining geophysics were reported to be $53.7 million in 1980, compared to $44.4 million in 1979, and $31.6 million in 1978. During 1980, approximately 2% of all dollars spent on geophysics were attributed to mining geophysical activities; this percentage has remained relatively constant in recent years. Airborne surveys accounted for 51% of the total worldwide mining geophysical expenditure, 43% was spent for land surveys, and 6% for borehole surveys. Within the US, the breakdown of expenditures for land surveys was 60% for elec¬trical methods, 23% for gravity and magnetic methods, and 17% for seismic techniques. Electrical techniques remain the primary exploration tool for US mining geophysicists. Electrical Methods With inductive or electromagnetic (EM) techniques, significant developments were achieved in both frequency-domain and time-domain systems. Work continued on increasing the signal level on most time-domain (TEM) methods, to increase the exploration depth. The Crone group increased the power of its Pulse ElectroMagnetic system (PEM) to a 20-amp transmitter-loop capability. The GEOEX group is modifying the SIROTEM II system to obtain larger transmitter amperage from a portable motor generator. Geonics developed a new digital recording system (data logger) for its EM-37 system. This development should increase the productivity of EM-37 crews. A new ground, frequency-domain EM system was developed by the Scintrex group. This novel Genie system does not require a wire link between the receiver and transmitter. Because an amplitude-ratio is measured, the Genie data are reported to be relatively insensitive to coil orientation and distance errors. This new technique does not need extensive line-cutting or accurate station-chaining and would appear to be a good reconnaissance instrument. Scintrex also began marketing the new IPR-11 induced polarization spectral receiver. This receiver is microprocessor controlled, and can output to a cassette tape and record 10 windows of secondary voltage decay simultaneously from up to six receiver dipoles. The Phoenix group's new 100 kW induced polarization/resistivity (IP/R) transmitter began tests using their IPV-3 multifrequency, multichannel receiver. While this unit was primarily developed for "oilfield" IP exploration research, it has obvious application to "deep" mineral exploration. The Phoenix group also developed a new remote-reference, real-time magneto-telluric (MT) device in 1981. This five-component MT sys¬tem has a frequency range from 0.0005-384 Hz. Helicopter-borne electromagnetic (HEM) developments also continued in 1981. The mining in¬dustry increased its use of the new Geonics EM-33-3 multifrequency, multicoil instrument. In 1981, the Dighem group developed software for estimating magnetite as a mapping parameter from its HEM system. Dighem's work is said to complement airborne magnetic intensity surveys, since the HEM estimate is independent of remanent magnetism and magnetic latitude effects. Gravity and Magnetic Methods Probably one of the most innovative techniques in geophysics in 1981 was the use of airborne gravity surveys for both mining and petroleum exploration. The Carson group is using a modified, shipborne LaCoste-Romberg platform in helicopters. Data accuracies to 0.5 milligal have been achieved by flying gridded surveys. Although this airborne method is expensive-up to $186/ km ($300/line-mile)-the geophysical community has been excited by initial results. On the ground, the portable proton-precession magnetometers are becoming sophisticated. Both GeoMetrics and EDA recently introduced field magnetometers having data storage and processing capabilities. This development should greatly increase the productivity of ground-magnetic surveys. Seismic Methods Development of high-resolution seismic techniques continued in 1981. These techniques have primarily been directed toward coal studies for fault detection. OYO Instruments introduced their McSEIS-1500 seismic data acquisition system in 1981. This device contains a 24-channel recording capability, with digital output to 256-kbyte floppy disks. The high-speed data transfer using the disk media is considered a desirable feature. Borehole Methods The general decrease in uranium exploration, where borehole logging is extensively used, probbly led to the overall decline of geophysical logging activity in the minerals industry. However, a number of new sondes and logging systems were introduced in 1981: • Mount Sopris recently introduced their Series III logging system. This microprocessor-controlled unit records up to four channels of data on nine-track or cassette magnetic tape. The logging package is relatively light-weight, so helicopter transport to mountainous or roadless exploration sites is possible. (Both the Edcon and Woodware-Clyde consulting groups offer "slinging" capabilities for their Mount Sopris units.) Mount Sopris is continuing work on their 500-mm-diam (2¬in-diam) spectral gamma-ray sonde. This tool is expected to be available soon. • Owl Technical "slim-downed" its successful digital deviation probe to 380-mm (1.5-in) outside diameter. This new sonde will also measure inclinations up to 80° from the vertical, as compared with its older instrument that could measure inclinations to 30°. • A magnetic susceptibility sonde was introduced in the US by the OYO Instruments group. This Kappalog sonde contains two aircored coils for measurements slightly affected by thermal changes within the borehole. The increased activity in massive-sulfide exploration and the need to "look" deeper no

Jan 5, 1982

By Charles R. Nelson

INTRODUCTION The support of openings in weak sandstones can be achieved by spraying on a liquid grout which will soak in and harden to form a shell. In the St. Peter sandstone of the Minneapolis-St. Paul area of Minnesota compressive strength is increased from about 0.7 MPa (100 psi) to over 7 MPa (1000 psi) to depths of 152 mm (6 in.). A shell of this strength and thickness can pro¬vide support much as shotcrete does but at lower cost. If the spray-grouted shell is inadequate for the support needed, it provides a good base for shotcrete application, which is often difficult in weak or friable sand¬stones because the fresh shotcrete peels off along with a thin layer of sandstone. The spray-grouted technique was initially developed at the Civil and Mineral Engineering Dept. of the University of Minnesota using funds provided by RANN Div. of the National Science Foundation. It was used as temporary support in a 3-m (10-ft) wide, 3700-m (12,000-ft) long storm water drain tunnel by the Minneapolis Sewer Construction Dept. Much of the field development at this construction project was carried out with the cooperation of the personnel of the city of Minneapolis. It also was used for temporary support in a 3.3-m (11-ft) wide, 1800-m (6000-ft) long storm water tunnel built in 1978-1980 for the Minnesota Dept. of Transportation in Minneapolis. In 1975, 2000 m (6500 ft) of 1.5-m (5-ft) wide utility tunnels were spray-grouted for final lining. A 50-m (150-ft) long, 1.2-m (4-ft) wide test tunnel built at the university in 1974 was sprayed for half its length and is being observed for long-term behavior which to date (1981) is good. GROUT MATERIALS The requirements for the liquid grout are more severe than those for injection grouting. Besides being able to penetrate the rock and develop sufficient strength, it must have the following properties: (1) be nontoxic, noncombustible, and have a low odor for spraying under¬ground; (2) have controllable viscosity and setting time for adjusting to the permeability of the sandstone and the required depth of penetration; and (3) must "wet" the sandstone and develop capillary "draw" to penetrate to the required depth. A sodium silicate-based grout with the proper setting agent meets these requirements in the local St. Peter sandstone which has a uniform grain size dis¬tribution curve with D,,, = 0.1 mm, permeability of about 10 to 20 darcys, a porosity of about 25%, and less than 5% of silt size or smaller. It is 97 to 99% pure SiO2. The grout mix consists of Philadelphia Quartz Co. Type N sodium silicate and Celtite 55 Terraset Spray Grade (SG) distributed by Celtite Inc., Cleveland, OH. A volume mix ratio of 100:9:125 for sodium silicate to setting agent to water produces a grout with two to four centipoise viscosity, and initial set at 20°C of 20 min. Setting time is temperature dependent, being longer at lower temperatures, but can be adjusted by varying the setting agent concentration a few percentage points. APPLICATION The application is simple. Spray the grout on the surface until the desired penetration is achieved. Penetration rates of about 5 mm (0.2 in.) per min. are realized in the St. Peter sandstone for up to 152 mm (6 in.) of penetration (30 min. of spraying). The set time must be longer than the spraying time. The spray nozzle should be moved back and forth at a rate that minimizes runoff due to surface buildup. Both a single large hand-propelled nozzle and multiple small machine propelled nozzles have been used successfully. The pumping and mixing equipment used consisted of: (1) a hand-held, hand-pumped, 11-L (3-gal) gar¬den sprayer for test patches (mix by shaking); (2) 76-L (20 gal) batch mixing in barrels with small electric pumps for spraying and mixing; (3) two component pumps consisting of Hypro Model 5300 piston pumps (Hypro Pump Co., St. Paul, MN) on a common shaft driven by an electric motor. The sodium silicate is premixed with a portion of the water and the setting agent is mixed with the rest of the water. The two components are combined and mixed just before the nozzle; and (4) a proportioner metering the setting agent just before the nozzle with the water and sodium silicate premixed and pumped from the surface. The proportioner permits the bulk of the grout to be pumped through a single pipe or hose with only the setting agent stored underground. This is efficient and low in cost. COST The grout mix costs about $0.20/L ($0.75 per gal) in 1978 dollars. Filling all the voids 100 mm (4 in.) deep (25% initial porosity) would have a materials cost of about $5.40/m2 ($0.50 per sq ft). The labor cost of application is usually less than the material cost for normal tunnel jobs. A pump and proportioner cost less than $1000. Sodium silicate storage tanks and pip¬ing costs would depend on the particular site conditions. REFERENCES AND BIBLIOGRAPHY Nelson, C. R., 1977, "Spray Grouting for Tunnel Support and Lining," Underground Space, Vol. 1, No. 3, pp. 241¬ 245. Yardley, D. H., Nelson, C. R., Stocker, T. H., 1974, "So¬dium Silicate Spray Impregnation of Tunnels in the St. Peter Sandstone," Research Report, University of Min¬nesota, 118 pp.

Jan 1, 1982

By Ning Liu, Di Yin, Xuming Wang, Yongqiang Lu, Jan D. Miller

Air-sparged hydrocyclone (ASH) flotation technology has been evaluated for phosphate recovery from the central Florida phosphate deposits. As expected, it was demonstrated in pilot-plant tests that the ASH system has a specific capacity about 50-100 times higher than that of a traditional flotation cell. In the case of fatty acid flotation, single-stage ASH flotation produced a recovery of 75-77% in a rougher concentrate containing 24% P2O5 In reverse flotation with amine, the single- stage ASH system produced a phosphate recovery of 98% in a cleaner concentrate containing 31% P2O5. These results are comparable with those obtained at plant operations in the Florida phosphate industry. Based on these pilot-plant results, the effects of process variables are discussed in terms of separation efficiency. Subsequently, a 6-inch ASH system was fabricated and tested in a central Florida phosphate plant for reverse flotation in the amine flotation circuit. The high capacity of the ASH system was again demonstrated for the 6-inch ASH system. A single-stage phosphate recovery of 91% was achieved with a concentrate grade of 30% P205. During plant tests, it was established that porous tube plugging, the most significant engineering problem identified, was due to the poor quality of the plant water. Possible solutions to this problem are discussed.

Jan 1, 1999

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By S. Triantafyllidis

The tailings produced from the Kirki (Agios Filippos) high sulfidation epithermal deposit processing plant are laminated, weakly cemented and their particle size ranges from fine sand to fine silt. They are mainly composed of milling residues of gangue (quartz, dickite/kaolinite, pyrophyllite, illite); sulfides and secondary minerals (jarosite group minerals, butlerite, anglesite, beudantite and gypsum) are present to a lesser extent. They have high Pb and Zn (average 0.75 % and 0.57 % respectively) and low S (1.04 to 2.92 %), Cu, As, Cd, Ni and Sb content (average 248, 163, 59, 27, 20 g/t respectively). Stagnant waters forming small ponds on the surface of the impoundments exhibit low pH and high heavy metal and sulfate concentrations. Negative Net Neutralization Potential (NNP) characterizes the tailings, indicating moderate to high potential for acid generation. Application of the TCLP test revealed that the tailings are characterized as toxic because of the increased solubility of Pb and Cd. On the other hand, As TCLP solubility is very low.

Jan 1, 2006

By Frank G. Horino, V. E. Hooker

INTRODUCTION The determination and use of mechanical properties of rock in engineering and rock mechanics are rapidly developing. Many of these properties are determined on intact rock specimens; thus, their application and repre¬sentation of rock mass properties may be limited. How¬ever, relative information often provides useful guidance in the solution to mine design and stability problems. Summarized in this chapter are some of the stan¬dardized techniques and procedures currently used to obtain these mechanical properties. Typical applications of the use of these properties are also presented. Stan¬dardized techniques include those advanced by the American Society of Testing and Materials (ASTM), International Society of Rock Mechanics (ISRM), US Bureau of Mines (USBM), Canadian Dept. of Mines and Technical Surveys, South African Institute of Min¬ing and Metallurgy, and other individual investigators. Information on the mechanical properties of rock and the behavior of the rock under a given system of stresses represents a necessary part of the information for rational engineering design for any given mining op¬eration. The mining method, the type and extent of sup¬port, the extraction ratio, the overall dimensions of the mine, and the orientation of the rooms and pillars are all decisions that are influenced by the mechanical prop¬erties of the ore, roof, and floor material under various stress systems and the magnitude and direction of the in situ stresses (Hooker, Bickel, and Aggson, 1972). Initial mechanical property information regarding a structure or mine property is generally obtained by two basic techniques: (1) static and dynamic property tests are conducted on intact and fractured rock specimens of exploratory drill core, and (2) dynamic properties are obtained by borehole logging techniques. When mining access becomes available, and as the mining horizon is expanded, additional information can be ob¬tained to verify preliminary mine design values. This chapter presents some of the standardized tech¬niques and equipment currently used in obtaining me¬chanical property data in the laboratory. The properties considered are: (1) uniaxial compressive strength of intact rock core specimens, (2) uniaxial compressive strength of rock cores containing planes of weakness, (3) triaxial compressive strength of intact rock core specimens, (4) triaxial compressive strength of cores with a plane of weakness, (5) Young's modulus, (6) Poisson's ratio, (7) density or apparent specific gravity, (8) modulus of rupture, (9) indirect tensile strength, and (10) creep characteristics. Where possible, an at¬tempt will be made to evaluate each property measure¬ment in relation to the problems of rock mechanics and application of results. TEST SPECIMENS The selection and care of drill core for laboratory testing require some consideration. It is recognized that laboratory-determined properties are not necessarily rep¬resentative of an in situ rock mass property. However, relative information between beds or zones of interest is still valuable information in selecting mining horizons and preliminary design criteria. To provide statistical data the number of drill core samples selected to repre¬sent each of the areas of interest should be from a mini¬mum of three to a maximum of ten test specimens. A judgment must also be made on site as to whether the recovered drill core should be wrapped and sealed in plastic to preserve moisture. On the one hand investiga¬tions of air-dried and saturated specimens have shown that moisture significantly affects the elastic properties and strengths of many rock materials (Obert, Windes, and Duvall, 1946; Colback and Wiid, 1965); on the other hand it is apparent that most core drilling is done with water which may saturate the specimen to a greater extent than in the in-situ condition. Whether or not the decision is made to retain the moisture, the core should be delivered to the laboratory as soon as possible after recovery for subsequent specimen preparation and testing. Specifications Shape: The shape of the specimens influences lab¬oratory testing in two ways: (1) time and cost of sam¬ple preparation and (2) strength of the material. Cy¬lindrical specimens of drill core are by far the least time-consuming to prepare for static or dynamic labora¬tory testing. In addition, the cylindrical shape lends it¬self to a more uniform stress distribution throughout the sample than other shapes, such as rectangles and hexa¬gons. The compressive strengths of various shapes have been studied (Grosvenor, 1963, and Price, 1960), and results indicate that the cylindrical specimens usually provide the highest strength for a given height-diameter ratio. However, reduction in strength from a cylindrical shape to a rectangular in situ pillar is not regarded as significant in relation to other considerations such as planes of weakness in a pillar or safety factors in the design process. Length-Diameter Ratio: The length-to-diameter ra¬tio, LID, has a significant effect on the compressive strength. Various recommendations have been made to use standard LID ratios ranging from 2 to 2.5 to 3 (ASTM, 1975c; ISRM, 1972). However, past work by others such as Obert, Windes, and Duvall (1946) has shown that excellent results can be obtained using LID ratios from 2 > (LID) > >/s. In selecting an LID ratio for testing, one should keep in mind the amount of material available for testing. In many instances, this may be limited. Thus, a shorter specimen such as 1: 1 LID may be necessary to provide enough test data for statistical analysis of results. Sec¬ond, it may be desirable to obtain elastic constants dur¬ing the test. This generally requires instrumentation such as linear variable differential transformers (LVDTs) or strain gages near the center of the specimen. In this case, an LID of 2.5 or 3 is desirable so that the instru

Jan 1, 1982

By Ralph S. Mattson, Frederick T. Hancock

GENERAL DESCRIPTION The Granduc mine is situated on the west side of Granduc Mountain in the Leduc River area of north¬west British Columbia about 51 km (32 miles) north¬east of the town of Stewart. Entry is by means of a 16.6-km (10.3-mile) long haulage adit from the concentrator site at Tide Lake. The principal ore mineral is chalcopyrite. Ore mineralization varies from dis¬seminated to irregular semimassive stringers generally associated with highly folded and sheared biotite-rich sections of metasediments. The ore bodies vary in width from 3.6 m (12 ft) to over 18 m (60 ft) in a zone some 800 m (2600 ft) in length dipping at an average of 75° to the west and plunging steeply to the south. Capping varies in thickness from 0 to over 300 m (1000 ft). SELECTION OF MINING METHOD In the early stages of planning the primary require¬ments to be met by the mining method were: (1) suit¬ability to high output and productivity, (2) adaptability to mechanization in order to minimize operating costs, and (3) minimization of the costs and the development period for preproduction. Considering these, the selection of a mining method was narrowed to a choice be¬tween sublevel long-hole stoping or sublevel caving. A method utilizing backfill was ruled out as uneconomical, especially since mill tailings would not be readily available. At the time, the following facts about the ore body were recognized: (1) the average width of the ore body was 12 m (40 ft), (2) 30% of the stoping blocks were in areas of 6 m (20 ft) or less in width; (3) in many cases, ore zones were located in parallel lenses or were irregular in shape; (4) major faults were present in the hanging wall close to the ore, with minor faults within the different ore zones; and (5) the ore itself was lami¬nated with fractures and jointing crossing such bedding planes. Considering these factors, the two stoping meth¬ods were compared. Sublevel Open Stoping The characteristics of sublevel open stoping are: 1) It is generally not used for widths below 6 m (20 ft) since the ratio of waste development increases as level intervals are reduced to insure good control of long-hole drilling. 2) This method is used where ground is relatively competent. Otherwise more pillar support is required, increasing ore losses or mining costs with pillar recovery. 3) The method is not easily adaptable to parallel ore zones separated by relatively narrow waste bands. 4) Close control of pillar and stope design will per¬mit some degree of dilution control. Sublevel Caving Sublevel caving is characterized by the following: 1) The method can be used for a variety of ore widths, recognizing that 3 m (10 ft) in width may be an economical minimum. 2) It is particularly favorable where wall rock is weak. 3) The method has flexibility so that irregular ore bodies or parallel lenses can be mined. 4) The need to leave pillars for support is eliminated 5) Dilution and tonnage recovery are interrelated. With concern about the stability of the hanging wall and the geometry of the ore bodies, there was a growing favor to choose the sublevel caving method. However, this method was relatively new to Canadian mining practice. Teams were sent to Sweden to tour mines using sublevel caving and to study their methods and any extraction and dilution problems. The objective was to develop cost and performance data and ore recovery grades and tonnages for feasibility comparisons. Next, detailed mine plans were developed covering a three-year period using sublevel caving and sublevel open stoping. Extensive analyses of the development and production costs for each method were made. With sublevel caving, ore losses of 10% with a 20% dilution rate were used. The same ore loss was estimated for sublevel open stoping with dilution varying from 11 to 15%. As a result of these studies, the decision was made to use sublevel caving partly because slightly lower op¬erating costs, together with higher productivity, offset the adverse effects of higher dilution; and partly be¬cause, at the start, there would be less risk in being able to handle the ground, and the method offered more flexi¬bility. Open stoping was not ruled out for testing at a later date. It was recognized that some other method of mining would be required for mining the ore extensions below the glacier, where surface subsidence must be avoided. During the operating life of the mine, open stoping was tested in narrow width ore zones and found un¬satisfactory due to wall failure. A cut-and-fill stope, utilizing run-of-mine waste from development, was also operated on a trial basis. A sequence was finally estab¬lished that permitted ground control; however, produc¬tivity needed considerable improvement in order for open stoping to be considered as a sole alternative for mining below the main haulage level. At the termination of operations in June 1978 over 13 000 000 t (14,500,000 st) had been extracted from above the main haulage level at production rates varying from 3270 to 7250 t/d (4000 to 8000 stpd). Sublevel Caving Methods Two basic methods were used, transverse and longi¬tudinal. The transverse method was used mainly in the upper C ore body in widths greater than 18 m (60 ft), and occasionally as an alternative to the longitudinal method in localized areas where strike faulting inter¬fered with normal development. The longitudinal method was used in ore bodies varying in width from 3.6 to 18 m (12 to 60 ft), with a multilongitudinal varia

Jan 1, 1982

By Mortimer J. Richardson, Earl H. Malmstrom

INTRODUCTION The art of placer gold mine evaluation and mining has had an interesting evolution beginning in earliest times. DE RE METALLICA (c.1556), documents the use of rockers, circular sieves(jigs) and riff lest for classifying, concentrating and recovering placer gold, respectively. During the late 1800's in the heat of the international gold rush, a bucket ladder mining dredge containing its own processing plant was developed that enabled digging of placers to bedrock that were inaccessible to the hand miner. The power driven churn drill was developed at about the same tie that facilitated more rapid and larger scale sampling of placers to bedrock. The mineral jig was applied in the early part of the 1900,s to begin the replacement of riffles on placer dredges. Mining dredges proliferated in California and New Zealand to mine the deeper placers and spread throughout the world. The companies that were leaders in dredge mining technology conducted experimental work that advanced the state of the art by processing of gravels with jigs and amalgam systems to recover gold on board dredges in a continuous process. This paper will synthesize the technology of placer gold exploration, mine development and operation into guidelines for evaluation and development of small-scale prospects. Prospect Reconnaissance The location of a prospect usual1 y results from some physical evidence of the presence of gold and/or past mining activity. Any earlier activity that may have produced gold from the prospect, should be investigated before making the trip. The initial reconnaissance should attempt to verify a near-surface presence and then make observations concerning the geomorphic characteristics that relate to placer gold accumulation. Estimates of the probable depth, breadth and length of mineable gravels can be made from the surf ace by the experienced placer mining engineer. With this information, he can speculate on whether there is a viable prospect to be pursued. The placer mining engineer should be experienced in panning samples found in shallow diggings or from existing pits. This will give him immediate indications of gold presence without fear of "salting" by an over-ambitious promoter of the project. The same capability of panning is important during the other sampling phases. A thorough knowledge of logging and calculating the results is essential to proper evaluation of the deposit' s tenor. Evaluation Methods Depending upon the character of the prospect such as river, benches, terraces, jungle, the type of equipment to conduct sampling of the deposit must be determined. In most cases, the drill has replaced bulk sampling. The churn drill has had the greatest amount of accumulated experience but is slow. The reverse circulation drill (RC), is limited by its lack of verification in subsequent mining in order to prove its reliability. However, in the hands of knowledgeable placer mining engineers experienced with its use and calibration, it may be used. The RC Hammer drill (such as the Becker), can be as much as ten times faster than the churn drill and compress the time necessary to prove a prospect, or, to disprove it. All costs in balance, it is often cost effective over the churn drill.

Jan 1, 1987

By J. P. Sieverson

The Comprehensive Environmental Response, compensation, and Liability Act (CERCLA -commonly referred to as Superfund) was passed into law in December 1980 in the wake of such incidents as Love Canal and the Valley of the Drums. Superfund was originally perceived as a way of cleaning up spills of hazardous substances and/or cleaning up abandoned hazardous waste dumpsites. In February 1981, Michael Cook, EPA deputy assistant administrator for hazardous emergency response, called Superfund "a tremendously powerful law. It could revolutionize the way the environment is protected, but we certainly don't intend to realize the full potential of the law for some time." These words have proven prophetic for Asarco's East Helena Smelter.

Jan 1, 1988

By Hans von Michaelis

Welcome to RANDOL GOLD FORUM 88. It is clear from the list of delegates and speakers that this conference will lead to excellent discussions of the latest developments in this fast-moving industry. Less than a year ago Randol International Ltd. published an eleven-volume report titled "Innovations in Gold and Silver Recovery - Phase 111". In the short space of time since then, many new developments have been noted, many of which will be described in this Forum. I believe that some of the more significant innovations currently under development are those that address the following:

Jan 1, 1998

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By Donald R. East

For many years there has been increasing pressure on mining companies, not without some justification, to design tailings storage facilities which guarantee some degree of protection against process solutions entering local groundwater and surface water flows. A fairly straightforward approach to achieving this has been to design conventional water-retaining type structures, and this has often been reinforced by the need to store large volumes of process water and seasonal run-off within the tailings facility. The conventional design uses naturally occurring geological barriers and a conventional embankment with possibly a grout curtain, or artificial barriers around the entire facility, using either imported low permeability soils, admixtures, or synthetic liners. While these approaches may achieve the primary objective of minimizing seepage, various other factors should be considered. Firstly, by depositing the tailings slurry in a sub-aqueous manner, the tailings, especially if relatively fine grained, will settle to very low densities and little or no on-going consolidation may occur over the operating life of the mine, There have been many cases where measured pore pressures within the tailings mass equal the total overburden stress, i.e., no consolidation and no strength, many years after decommissioning.

Jan 1, 1998