Search Documents

By Duane B. Jorgensen

The two calcium sulfate minerals, gypsum and anhydrite, occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO, . 2H20) and anhydrite, the anhydrous form (CaSO,) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the larger part of total calcium sulfate resources. Although it has very minor economic use, it is important to the understanding of gypsum deposits and is referred to frequently in the following discussion. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have not yet been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. Most gypsum produced ranges from 80 to 95% pure and beneficiation is normally limited to selective mining or quarrying or upgrading by crushing and screening during mill processing. END USES The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris, the hemihydrate of calcium sulfate (CaSO4 ½ H2O), which when mixed with water will set or harden as the calcium sulfate returns to the stable dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uses of uncalcined gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in other countries with building practices different from those in the United States and Canada, relative usage varies widely. Calcium sulfate deposits are the world's largest sulfur resources; minor quantities of gypsum and anhydrite have been used to produce sulfur or sulfur compounds. This use is accompanied by a unique site-specific set of economics because sulfur is generally available from non-gypsum sources at lower cost.

Jan 1, 1994

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By Y. Luo, S. S. Peng, C. T. Holland

Introduction A well-designed mining plan is one that minimizes cost and mining induced problems and maximizes recovery of the coal reserve. To minimize the negative effects on surface structures caused by ground subsidence due to underground mining activities, two kinds of practices are commonly employed by mine operators. One is the support technique, which leaves an area of coal unmined or partially mined beneath the structure to be supported. The other is the protection technique, which protects the structure when it is subsiding with the ground by taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting technique, the only currently available method in the US is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However, the size of the support area designed by this method will be excessively large and result in a wasteful use of coal reserves when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for designing the support area. This method is based on a large amount of subsidence data collected throughout a number of major US coal fields and the authors' experience with monitoring and protecting surface structures that have been undermined by longwall panels. It considers the critical deformation indices that a structure can tolerate, and depth and height of underground extraction. A support area designed by this new method will not only assure the safety of the structure to be supported but will also maximize the extraction of the coal reserve. Design of support area using the Pennsylvania rules The Pennsylvania Underground Coal Mining Rules (1985) state that no underground mining activity should be permitted beneath structures where the overburden depth is less than 100 ft. An exception to these rules is provided for mine related openings that provide access to the surface for such as entries, shafts, boreholes and site-specific variances for entry development. If the overburden depth is greater than 100 ft, the mine operators should utilize either of the following: •Extraction techniques that provide for planned subsidence in a predictable and controlled manner, or •Support techniques designed to prevent subsidence damages to features identified as: •Public buildings and non-commercial structures [ ] customarily used by the public, including churches, schools and hospitals • Dwellings, cemeteries, municipal public service operations and municipal utilities in place on April 27,1966 •Impoundments and other water bodies with a storage capacity of 20 acre-ft or more • Aquifers, perennial streams and water bodies that serve as a significant source for a public water supply system, and •Coal refuse disposal areas. The support techniques require that a support area be left beneath the surface structure or feature to be protected (Fig.1). The support area should consist of coal pillars, with their size and pattern being such that their bearing strength is maximized. The total coal extraction within the support area should be limited to a maximum of 50%. The support area should be rectangular in shape and determined by projecting a line at a 15° angle from the surface to the coal seam with an offset distance of 15 ft from all sides of the structure. For a

Jan 1, 1994

By Dale S. Preece

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is a research facility located in Southeastern New Mexico. The WIPP is being developed by the U. S. Department of Energy (DOE) to demonstrate the safe storage of defense-related radioactive wastes in bedded salt. Since the WIPP is a research facility. a number of large-scale in situ experiments have been planned and are currently under construction (Munson, 1983). These experiments were designed to study various aspects of nuclear waste storage in bedded salt such as mechanical responses and creep closures of drifts, thermal response due to heated canisters, and thermally-induced fluid migration. One purpose of the WIPP is to develop and demonstrate a general predictive structural analysis capability for a bedded salt repository. One set of experiments, called the Geomechanical Evaluation (Room G), is heavily instrumented to study the creep around several rooms with different configuration. A Layout of the Geomechanical Evaluation room is shown in Figure 1. One portion of it consists of wedge shaped pillar where two drifts intersect at an angle of 7.5 degrees. The pillar can be seen at the bottom of Figure 1. One purpose of the wedge pillar experiment is to study progressive pillar failure in the tip region. Another is to determine how nonuniform pillar thickness affects creep closure of the drifts. An important aspect of the experiments is the correlation between experimental data and corresponding pretest finite element analyses of the site. The finite element simulations serve two purposes. First, the computer simulations aid in understanding the experimental results by providing calculated stress. strain and displacement fields that cannot be measured directly. Second, comparison of calculated and measured drift closures serves as a method for validating or improving the finite element models and the constitutive models employed. The wedge pillar geometry required a 3-D finite element creep calculation. Results from these 3-D calculations will be presented in this paper. A 2-D plane strain double drift model which approximates the wedge pillar geometry at a slice perpendicular to the drift has also been performed and will be compared to the 3-D results in this paper. FINITE ELEMENT COMPUTER PROGRAMS Two finite element computer programs. JAC (Biffle, 1984) and JAC3D (Biffle. 1986), were used. JAC is a 2-D finite element program developed for quasi-static analysis of non-linear solids. It employs the conjugate gradient iterative technique to obtain a solution Spatial integration is performed using a single gauss point in each four node quadrilateral element. An hourglass viscosity technique is used to control the zero energy modes that occur with single point integration. The single point integration combined with the explicit nature of the program and exploitation of CRAY-1 computer architecture results in very efficient execution J4: results were compared to results obtained with eight other 2-D structural creep computer codes in the second WIPP benchmark exercise (Morgan, 1981) JAC3D was derived from JAC to treat 3-D finite element models and has many of the same characteristics including single point integration and hourglass viscosity. These characteristics have made 3-D creep analyses more reasonable by significantly reducing computation time The first exercise of the creep capability

Jan 1, 1986

By Wallace W. Roepke, James C. Church

Introduction The history of mining machine development has been and is one of "bigger is better." While this may not always be true, it is currently the only approach open to machine designers without specific in situ cutting force information. The US Bureau of Mines has tried to modify this approach by supporting research, both in the laboratory and in field tests, that demonstrates that bigger is only better if the equipment is used correctly. In-house research has shown conclusively that deeper cutting reduces both dust and energy (Roepke, Lindroth, and Myren, 1976). This approach has been applied to a large Lee-Norse (LN456) continuous mining machine, which confirmed that slow deep cutting is beneficial and does not have a negative effect on production (Black and Rounds, 1977; Black et al., 1978). Specific in situ engineering data needed on coal cutting forces have not, however, been obtained by field tests with the LN456. Although the machine was instrumented to obtain data on one seam, it would be impractical to move the machine from mine to mine. It became apparent that a portable, easy to use device was needed for obtaining coal cutting forces in situ. Such a device could provide the engineering data needed by manufacturers, the site-specific cutting information needed by operators, and a field research tool to establish correlation with laboratory cutting tests. Design and Development According to a set of design guidelines established by the Bureau, the proposed device should be able to measure cutting forces directly with standard coal cutting bits, be transportable by two miners, and be self-contained. These guidelines were given to Ingersoll-Rand Research Inc. (IRRI). The contractor performed a rigorous review of 16 existing in situ portable tester designs, none of which could use a standard coal cutting bit to measure cutting force directly. These included a wide range of devices, all of which are discussed in the final report (Banerjee and Wisner, 1982). A series of design tradeoffs were established to satisfy initial design guidelines. The final deci¬sion was heavily weighted by an industry survey to determine the preferred concept from four man¬ufacturers and four operators. To assure ease of use with maximum information, all respondents wanted a linear cutting device that could work in seams down to 1 m (40 in.). The final design choice was between a linear and a rotary tester. The rotary tester would cut on an arc in the same manner as a rotary drum machine. It had several faults, however, that could not be resolved within the scope of this contract. The worst was related to arc cutting (Roepke, Lindroth, and Myren, 1976). Since any bit cutting on arc enters the coal at zero depth, goes to maximum depth only at the horizontal centerline, and exits at zero, maximum cutting force is obtained only at the instant the bit crosses the horizontal centerline. This centerline peak response would require that many replications be made with an arc-type cutter to get reliable force information. The arc-type tester would require extensive face preparation to establish the cutting path and extensive wasted clearing cuts to advance the device for additional layers of cuts. The linear tester could be mounted directly on any face or rib with only minor preparation. By its nature, a linear cut at a constant depth provides multiple peak force data over the length of the cut, thus reducing the required number of replications. The final review of these two major design concepts plus indus-

Jan 9, 1983

By Wallace W. Roepke, Richard C. Olson

To adequately attack the longwall dust problem, the US Bureau of Mines funded a contract to define dust sources on a longwall mine face area. The study examined the shearer during sumping, cutting, and tramming, the conveyor, and the roof supports. Tests showed the shearer to be the major dust source. Introduction Long-term illnesses place a heavy burden on miners, the mining industry, and taxpayers. Black lung payments to more than 400,000 miners and their survivors exceeded $9 billion between 1970 and 1980. They are continuing at a rate of $1 billion per year. Recent MSHA data indicate more than 50% of the longwall faces are still out of compliance with the 2 mg/m3 (0.00007 oz per cu ft) respirable dust regulation. Allowable dust limits are often further reduced owing to the presence of silica dust. This substantially increases the problem's severity. Research in the 1970s showed that by modifying the mining method through changing drum-type mining machines from high rpm shallow cutting to slow rpm deep cutting, both specific dust and energy could be reduced (Black et al., 1978; Ludlow and Wilson, 1982; Roepke, Lindroth, and Myren, 1976). The coal mining industry is using more longwall equipment to economically obtain high productivity. This high production rate, however, makes it difficult for longwalls to meet the legal dust standard. Research is showing how both these concerns may be addressed at the mining face. Results reported here explain the relationship of various major elements of the longwall system to dust generation on the longwall face. This paper is based on work completed by Foster-Miller Associates Inc. Objectives were to differentiate dust sources on the longwall face and to quantify dust levels for various elements of the shearer drum. The work was accomplished in two phases. Jonathon Ludlow, project engineer for FMA, developed and performed the necessary testing (Ludlow and Marshall, 1983). Bradley, Hadden, and Weston (1983) have done evaluations on British coal mines that produced similar results to those reported here. They found causative rela¬tionships between haulage speed, production, depth cut, drum speed, and dust generation. They also found that roof support movement increased the dustiness, whereas this work indicated that support movement had only a minor effect on total dust exposure. Both of these results are valid when the variation of mining conditions is analyzed. British mines are deeper than US mines. Therefore, roof rocks and coal are more fragmented than in the shallower US mines. Other reasons for the dust differences include the weaker shales found in Britain and the variation of roof support equipment designs between the UK and the US. Four mines in this report had rock roofs and, thus, would be less dusty. The fifth longwall mine had a coal roof, but the large cross-sectional area and high air velocity minimized dust exposure. Mines and Equipment Five underground longwall mine sites were tested (Fig. 1). All were using double-ended ranging-drum shearers (derds) with some variations in equipment. The mines and equipment details are shown in Table 1. No modification of mining equipment or operating cycles was made during the first phase of testing. The mining process observed followed the normal mine operating procedures. Three GCA RAM-1 respirable dust monitors and two vortex anemometers with cycle notations on portable tape recorders were used in each face area. The start and end of each cycle segment were recorded. Dust monitors record the dust levels once every 10 seconds, thus providing a relatively continuous real time indication of change in

Jan 8, 1984

By G. R. Laurer, J. W. Neton, C. Pomroy, N. Cohen, M. Eisenbud

INTRODUCTION In uranium miners, a causal relationship between exposure of the lung to high levels of alpha radiation and the consequential induction of bronchial carcinoma is now well-established (Wagoner, et al., 1965). Quantitation of this cause-effect association presents considerable difficulty, however, as the result of various confounding factors such as the contributing effects of smoking and/or arsenic exposure (Archer, Gillam, and Wagoner, 1976), normal metabolic variability and, perhaps most important of all, the absence of accurate radon/radon daughter exposure data. Estimates of cumulative lung exposures suffer from inaccuracy due to critical factors such as 1) unknown ventilation rates; 2) difficulties in obtaining representative mine air samples; 3) the variable character and magnitudes of the exposure sources; and 4) specific differences in metabolism and job histories that exist among miners. It was with considerable enthusiasm, therefore, that investigators readily embraced the idea of using skeletal burdens of the relatively longlived descendants of radon and its short-lived daughters, i.e., 210 Pb and 210Po (Archer, et al., 1968), to provide a measure of cumulative past exposure wherein the body acts as an integrating dosimeter. Early studies considered excretion rates of 210Pb and 210Po in urine, blood and hair (Sultzer and Hursh, 1954; Black, et al., 1968; Jaworowski, 1965; Bell and Gilliland, 1964) as well as their concentrations in bone samples, if and when they became available (Blanchard, Archer, and Saccomanno, 1969). These methods were ultimately complemented by in vivo, whole-body counting techniques using low background, NaI-Csl(T1) detectors (Eisenbud, et al., 1969). By this latter method, it would be possible to measure the skeletal burden of 210Pb directly, thereby avoiding the many difficulties associated with the relation between nuclide excretion rates and body burden. The rationale was simple; by knowing the skeletal burden of 210Pb it should be possible, by the judicious use of an applicable metabolic model, to estimate the cumulative lung exposure to alpha-emitting radon daughters (Fig. 1). Various models that were consequently constructed, however (Fisher, 1969), all suffered from the same limitation, i.e., the assumption that the source of 210 Pb in the skeleton and the source of lung exposure to the short-lived radon daughters were simply related and, if not, were at [ ] least not too variable (Raabe, 1970). By now, the difficulty with this assumption has been recognized and more sophisticated modeling techniques have been attempted which presumably present a more realistic picture of exposure conditions (Holtzman and Rundo, 1981). There is, nevertheless, the pessimistic view that due to the variety and variability (in time as well as in character) of sources that may exist for the origin of 210Pb in bone, it may [never] be possible to estimate past lung exposures accurately by an indirect, predictive model. For example, the origin of 210 Pb in the skeleton may include such sources as: 1) the decay of short-lived 222Rn daughters, inhaled and ingested; 2) the decay of 222Rn dissolved in body fluids and tissues; 3) directly from 210 Pb present in air, inhaled and ingested; and 4) 210Pb from non-occupational sources, e.g., food, water, smoking and endogenous 226Ra. The contribution of each of these sources may vary depending upon specific site conditions such as ventilation and mining operation. On the other hand, empirical evidence seems to indicate a trend reflecting the simplest of direct

Jan 1, 1981

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By Kenneth A. Rogers, Richard F. Hill

Introduction A number of processes for deriving more convenient liquid and gaseous fuels from coal are commercially available or in final stages of development. Generally, synfuels from coal processes have efficiencies ranging from 50 to 70%. Considerable engineering design and development work are necessary to bring forth commercial plants using the various technologies-but technological breakthroughs are not expected or needed. Gasification While a variety of solids handling, gas contacting, and gas quality upgrading techniques may be employed in the various gasification processes, the primary goal is the same-to convert a sulfur-containing solid to an essentially sulfur-free gaseous product. The gaseous product may be a mixture of hydrogen and carbon monoxide with nitrogen. Definitions are not rigorous, but high-Btu gas is generally over 900 Btu/scf(33 534 kJ/m3) and low-Btu gas is generally below 350 Btu/scf(13 041 kJ/m3). Medium or intermediate gas falls between these values. High-Btu production is more difficult, as it requires additional upgrading of a low- or intermediate-Btu gas stream to produce a commercially acceptable product. The carbon/ hydrogen ratio is adjusted either by rejecting a portion of the carbon, increasing the hydrogen, or a combination of both. The chemical processing steps include production processing gas containing carbon oxides and hydrogen by the reaction of carbon and steam (gasification); reaction of hydrogen and coal to form methane (a hydrogasification process); reaction of hydrogen and carbon monoxide to produce methane (methanation); and the removal of impurities. The gasification processes share a number of common techniques. The coal received at the plant site must be further cleaned and crushed or ground before it can enter the gasifier. Conventional cleaning methods are used to remove extraneous materials such as metal, rocks, etc. For some processes the coal must be finely ground so it may be fluidized or entrained in a flowing gas stream. For other processes crushing and sizing only are required. Agglomerating coals may be pretreated by heating, mild oxidation with air, or other procedures to assure smooth gasifier operation and to avoid reactor plugging. Nonagglomerating coals Such as lignite and subbituminous coal normally do not require pretreatment. Feeding a solid material such as coal to a higher pressure reactor is a difficult task. Dry feeders using a series of pressurized lock hoppers, or wet systems in which a slurry is pumped into the reactor, are used. The gasification step is the heart of the process. Here, the solid feed material is contacted with synthesis gas (carbon monoxide and hydrogen). The coal is devolatilized and a portion of the fixed carbon converted to methane. The gas-solids contacting methods used include fixed beds, fluidized beds, moving beds, entrained beds, and free-fall systems. The gasification process, overall, is endothermic and the heat required to maintain reaction rates is usually supplied by burning a portion of the coal feed. External heat sources such as electric resistance heating, molten salt or solid heat carriers, and the introduction of a hot hydrogen stream also have been tested. Following the gasification step the particulate materials and heavy hydrocarbons contained in the reactor effluent are removed by a water quench and solids separation system. If low-Btu gas or synthesis gas is the desired product, the raw gas is scrubbed to remove carbon dioxide and sulfur compounds and then is used directly. However, if high-Btu gas is desired, methanation is necessary. In most gasification processes, the hydrogen content of the gasifier

Jan 2, 1980

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By Jay S. Silhanek, Vernon E. Andrews

[Introduction] Section 122 of the Clean Air Act Amendments of 1977, Public Law 9595, directed the Administrator of the Environmental Protection Agency, to review all relevant information and determine whether emissions of radioactive pollutants into ambient air will cause or contribute to air pollution which may reasonably be anticipated to endanger public health. In August 1979, EPA published a preliminary report on assessments of public health impact resulting from emissions of radionuclides into air from a broad spectrum of major source categories (1). A section of this document presented a theoretical analysis of the radioactive airborne emissions from several non-uranium mines including iron, copper, zinc, clay, limestone, fluorspar, and phosphate. Since 1978 EPA's Las Vegas Laboratory has been gathering field data on actual radionuclide emissions from these mines to support the earlier theoretical analysis. The purpose of this paper is to present the results of those field measurements in comparison with the assumed values for the theoretical analysis. Data were presented in EPA's preliminary report on both gaseous radon-222 and particulate uranium-238 emissions from non-uranium mines. Most of the emissions data were rough estimates based upon the uranium content of the ore. Preliminary data from a few field studies were also used. Although both the theoretical and field studies by EPA were concerned with radon-222 and radioactive particulate emissions, this paper will concentrate only on the radon effluents. Radon from mines seems to have the greatest potential for possible health effects due to radiation. Data on particulate emissions are presented in other technical reports (2-5). [Theoretical Study] The theoretical emission data are presented in Table I. The estimates for the iron, zinc, and clay mines are based upon preliminary measurements taken by the Las Vegas laboratory. The estimates for the other mines were made assuming that 20% of the total radon-222 in the ore was released during the mining process and the radon release rate from the exposed ore surface was a factor of two greater than that resulting from mining. [ ] Dose assessments for radon from these mines were carried out using model facilities located on generic sites (1). The AIRDOS-II computer code (for estimating dispersion of airborne pollutants) with some minor modifications was used to determine working level exposures to a maximally exposed individual and a regional population. A conversion factor for risk/WL-year(O.021 fatal cancers/person-WL-y) was developed primarily from information on uranium miner exposures (6). This computer code and conversion factor were then applied to the assumed emission rate of radon-222 from each type of mine to develop estimates of working levels, lifetime risks and number of fatal cancers. A summary of this data is presented in table II. [ ] The highest estimated number of cancer deaths per year of operation is 0.05 cancer deaths or 1.0 death due to radon during the 24 year life of a phosphorous mine. For comparison, EPA estimates that underground uranium mines would cause .03 cancer deaths per year of operation in a regional population(1). [Field Study] As a followup to the theoretical study, EPA's Las Vegas laboratory began making measurements in 1978 of actual emissions of radon-222 and radioactive particulates from mine vents at several facilities for each of the industries listed in Table I and II. They were intended to verify general information and radon emissions from EPA's theoretical estimates.

Jan 1, 1981

By John A. Haggman

Philippines is a country that is richly endowed in mineral wealth. In 1988, Climax Arimco Mining Corp. (CAMC) geologists found the Dinkidi porphyry gold-copper deposit in Nueva Vizcaya province. It is the most significant mineral discovery in that country in recent times. To date, the company has defined indicated resources of 124 Mt (136 million st) of 1-g/t (0.029-oz/st) gold and 0.4% copper. This includes a high-grade core of 7.9 Mt (8.7 million st) of 6-g/t (0.175-oz/st) gold equivalent. Total contained metal is 124.4 t (4 million oz) of gold and 499 kt (1.1 billion lb) of copper. Dinkidi's discovery resulted from initial geologic reconnaissance and recognition of the intrusive complex that is exposed at surface and anomalous in its topographic expression. This was followed by systematic exploration. This includes extensive gradient array induced polarization (IP), ground magnetics, geochemical sampling and diamond drilling. This later defined a further 16 satellite porphyry targets in the Didipio region. Climax was been granted a Financial and Technical Assistance Agreement contract with the Philippine government. It allows 100% foreign ownership of mining projects. After four years of negotiations, Climax was the first company to have such an application granted. Some 120 applications from numerous international mining companies are waiting for approval following implementation of new Philippine Mining Act of 1995. Exploration history Didipio is located 200 km (125 miles) north of Manila at an elevation of about 700 m (2,300 ft) in the remote Sierra Madre mountains. This region remains mostly unexplored. The property is accessed by 25 km (15 miles) of logging track from the town of Cabarroguis, Quirino. The area experiences an average rainfall of about 3,000 mm (118 in.) a year. Most of it falls during the July-to-November typhoon season. Didipio was first recognized as a gold province in the 1970s when native Ifugao and Ilongot hunters discovered alluvial gold in the region. The region had been prospected over the years by local companies. They were mostly prospecting for alluvial gold. However, in 1988, Climax Mining geologists identified the potential of an obscure razorback ridge protruding from the alluvial valley floor. This ridge, later named Dinkidi by Climax, was the site of several small- scale tunnels. Locals had mined narrow quartz stockwork veining and sluiced soft argillic alteration zones, using irrigation canals and sluice boxes to catch free gold.

Jan 1, 1997

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By J. D. McAuliffe

The Homer-Wauseca Mine is operated by the Hanna Mining Company, three miles north of Iron River, Michigan on the Menominee Iron Range. The mine produces 5,300 tons of direct shipping iron ore daily. The present main producing level is at a depth of 1,500 feet below the collar. The ore body continues to a depth of 2,700 feet below the collar, to which depth the modern circular concrete shaft has been completed. A view of the property is shown in Figure #1. This paper is a report on the development of large underground boreholes used initially to conduct stope filling material into inaccessible, mined-out stopes. Later holes were drilled for ventilation raises, for mine drainage, for passageway for power cable, also for the primary breaking point for long hole stoping. Some, which were drilled as ventilation raises, were later stripped to a suitable size for a manway or ladder road. The holes varied in size from 6" to 30" with the present popular, economical working size being 16 1/4", used as a stope fill passage in mined out areas and for ventilation in deeper development. Foremost has been the desire to develop equipment suitable for drilling raises large enough for manways.

Jan 1, 1963

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

By V. L. Magnus

The text of this chapter was not received in time for printing.

Jan 1, 1979

By Stephen W. Lambert

One of the primary interests of the United States Department of Energy's Mine Planning Division is to fully develop avenues of technical research which potentially offer positive effects on coal mine productivity. One such area of research involves the removal of methane gas from unmined portions of coalbeds through vertical wells drilled from surface locations. As coalbed methane content is reduced, less gas is available for flow into the mine, and consequently ventilation requirements are decreased and/or coal extraction rates increase. Another attractive aspect of the vertical borehole drainage method is that it presents an opportunity to recover and utilize significant quantities of methane gas, which would otherwise be wasted to the atmosphere. The viability of removing gas from the Mary Lee coalbed using stimulated vertical boreholes was first suggested by Elder and Deul as a result of a United States Bureau of Mines' drilling project conducted from 1971 to 1974 (4). Other United States Bureau of Mines' studies forecasted that degasification would eventually be necessary in the Mary Lee coalbed because most new or expanding mine development would take place at depths exceeding 1 000 feet (305 meters), where the methane problem would be severe (3) (13). In 1975 a large-scaled drilling program was designed in order to supply industry's anticipated need for a degasification technology in the Warrior coal basin, Alabama. The results of this government/industry sponsored effort were to be specifically applicable to the Mary Lee coalbed, the most extensive and economically important deep minable coal present in the area. Major technical objectives of this program are twofold: (1) to measure the effects of various well completion designs, particularly hydraulic stimulation, on mining and (2) to determine the effects of well spacing on gas drainage rates. A cooperative agreement was established with United States Steel Corporation in late 1975 and field work began shortly thereafter in the proximity of a newly developing mine near Oak Grove, Alabama. Government responsibility for this program was transferred from the United States Bureau of Mines to the United States Department of Energy in October 1977. To date, as a result of this program, twenty-one wells have been completed into the Mary Lee coalbed at the Oak Grove site. Seventeen of these wells were drilled on an experimental grid pattern located two miles from the active mine. These grid wells are primarily being used to generate data necessary to determine the effects of well spacing on gas drainage rates and will also provide a large amount of information regarding the long-term effects of degasification on mining. The four remaining wells (designated Ton through TW4) were placed near the mine so that the full effects of completion could be studied within the short time required for underground interception. Results gathered from the first two test wells (TW1 and TW2) have been reported in detail (10) and indicated that several improvements were necessary to increase gas drainage rates. Hydraulic stimulation was one of the most important aspects of well design that required improvement. Nitrogen-charged foam stimulation treatment was used at TW3 and TW4 instead of the gelled-fluid type stimulation used at the first two near-mine test wells.

Jan 1, 1980

By Shan Mafi

he Broken Aro coal mine is located at the Woodbury Wildlife Preserve 11 km (7 miles) west of Coshocton, OH on State Route 541. Underground min¬ing at the 16-hm2 (40-acre) site took place during the 1910s. During the past five years, surface mining has occurred along the western and northern perimeters of the underground region. The Ohio Department of Natural Resources (ODNR), R&F Coal and American Electric Power (AEP) are involved in a project to remine the abandoned underground complex. The program also includes installing a mine seal made of fixated flue gas desulfurization (FGD) material. Previous mining activity in this area has resulted in an acid mine drainage (AMD) problem on portions of the reserve. In particular, a prominent AMD source is present in the Simmons Run drainage. The project goal is to eliminate or reduce the AMD that is discharging into the watershed. It was initially hoped that the Simmons Run drainage area could be economically mined. Accordingly, this area was included in the mine permit. However, experience with other previously mined areas on this reserve showed that the old mine workings were more extensive than originally thought. Old mine workings present several problems. The most significant are reduced coal recovery, poor coal quality and AMD liability. All of these problems increase mining costs. And the more extensive the old workings, the more significant the increase in cost. Based on R&F's experience with old mine workings in this area, it was decided that economic recovery of the Simmons Run drainage reserve was not possible. As a result, R&F excluded the Simmons Run drainage area from its early mine plans. Some time after it was decided not to affect the Simmons Run drainage area, R&F and ODNR's Division of Mining and Reclamation discussed the possibility of removing this area from the permit and attempting to correct the AMD problem as an Abandoned Mine Lands (AML) project. Specifically, the discussion centered around mining through a portion of the old mine workings to expose the mine openings in the highwall. Once exposed, the mine openings would be sealed using FGD material from the nearby Conesville power plant operated by AEP. In addition, there was interest in reclaiming the old tipple and associated gob pile located adjacent to Coshocton County Road 17 on the opposite side of Simmons Run. R&F attempted to eliminate the AMD problem by sealing the mine openings with FGD material. Once the seals were installed, they were covered with overburden. Monitoring wells were installed to determine the effectiveness of the seal and the inundation progress in the old mine workings as well as monitoring the quality of ground water. The project was jointly funded by revenue from the sale of the coal recovered during the project and AML funds. The FGD seal is expected to cause well water levels to increase above preseal elevations. However, the additional head pressure due to increased water depths in the underground mine may cause seepage through the bottom of the mine or out through the perimeter. The in¬creased water depth in the underground mine is expected to cause lower oxygen concentrations in the underground mine water. Since acidity is produced by oxidation of iron pyrites, less oxygen should result in better quality water. Monitoring wells will be installed before seal installation so that pre- and postseal water levels and well water quality can be determined. Surface sampling locations will be identified. These will be monitored before and after seal placement.

Jan 1, 1998