Search Documents

By Malcolm J. McPherson

The highest recorded loss of life due to the collapse of mine workings occurred at the Coalbrook North Colliery in South Africa on 21st January, 1960. A total of 437 persons died when bord and pillar workings collapsed over an area exceeding one square mile The whole mass of strata from the 470 ft (143 m) deep seam to the surface being affected. Although the Coalbrook disaster was unique in its scale the problem of pillar failure, particularly in old workings, is by no means uncommon nor confined to recent history. Indeed, the collapse of large pillared areas was a regular feature of mining in the north of England in the early part of the nineteenth century. When a section of underground workings collapses, the air under the descending roof is compressed very rapidly. The pressurised air is dissipated subsequently at a rate governed by the leakage paths available. If the collapsing area is small, such as the case of a local fall of roof, then there will be little danger of an air blast. If, however, an extensive area collapses suddenly then the rapid compression of air will give rise to a pressure shock wave that will be transmitted through the remaining workings as an air blast. If worked out areas are connected to current workings via unstopped airways an air blast caused by pillar failure in the old workings will be extremely hazardous to personne1 and may cause extensive damage to equipment, perhaps even reaching to surface plant. At Coalbrook, the air blast blew out a wall in the surface fan house. Areas that are considered liable to sudden collapse may be isolated from current workings by the construction of stoppings. However, such stoppings must be capable of withstanding the 'hammerblow' effect of peak air pressures developed during the collapse. The work described in this paper was undertaken in order to determine the maximum air pressures that stoppings must withstand during a major pillar failure. The result has been a method of establishing peak air pressures that is quick and simple to use. Readers who are concerned primarily with the practical application of the method are advised to turn directly to the last main section of the paper.

Jan 1, 1980

By John G. Whellock

Over the last decade new constraints have emerged in the metallurgical industry which challenge the very basis of design and construction of smelters and refineries. The hackneyed designs of the past will not now serve the revised objectives of: - minimal cost of ownership - improved productivity - reduced energy consumption - greater flexibility in feed or product - minimized recycle loops and by-products - more stringent environmental control The impact of these constraints has been channeled constructively into process intensification - exemplified at the large scale by the introduction of flash smelting technology and at the smaller scale by the application of rotary process vessels and converters for augmented heat and mass transfer. The design of successful process plants depends on the understanding of the unit operations and their interactions which is the discipline of systems engineering. With the advent of increased process intensification the importance of a systems approach to process design and implementation becomes paramount. This paper describes the systems approach with specific reference to medium scale projects in the primary and secondary metallurgical industry.

Jan 1, 1985

By Douglas J. Cork

Biohydrometallurgica1 processes in the areas of coal desulfurization (Hoffman, M.R., et al., 1981) and recovery of metals from metal sulfide ores (Lundgren, D.G. and Malouf E.E., 1983) are well known. In addition other areas of potential interest to the mining industries have been outlined (Spisak, J.F., 1979). For instance, scientists involved in this interdisciplinary field have endeavored to apply microorganisms to the problem of effluent sulfate disposal. This chapter assesses the feasibility of utilizing a particular two stage anaerobic microbial process to convert effluent sulfate to orthorhombic sulfur. Strong emphasis is given to the possibility of substituting this bioprocess for alternative gypsum synthesis and disposal methodologies commonly practiced by companies which emphasize sulfuric acid or ammonium sulfate leaching processes.

Jan 1, 1985

By Kathleen Y. Knoebel

This paper describes a graphical mini computer system called MPASS 2 (Mine Performance Analysis/Simulation) which has been designed to conduct analysis of underground room-and-pillar mining operations using both conventional and continuous mining methods. Dynamic, graphic displays of mine face machine activities are presented on the CRT screen to provide extensive visibility into underground mining activities. MPASS 2 consists of: an interactive inputting system that graphically creates a room-and-pillar mine and describes the mine when production is initiated; a time-step simulator that produces statistical summaries of shift activities and uses CRT screen graphics for accelerated-time display of machine activities and delays; a statistical analysis subsystem for analyzing mine performance data; an industrial engineering system that permits users to enter actual machine activity statistics and replay mine operations on the CRT screen; and a data management system to store historical performance information on mine characteristics and operations. MPASS 2 operates on a Hewlett-Packard 9845B mini computer with 450 K bytes of extended memory, and is written in H-P BASIC. It has been installed at Freeman-United Coal Mining Company in West Frankfort, Illinois and at the U. S. Department of Energy Pittsburgh Mining Technology Center. Applications include production system simulation, industrial engineering analysis, production scheduling, new equipment evaluations, and training.

Jan 1, 1982

By Charles G. Weakly, Alan M. Lander, Pamela B. Zohar, Robert W. Leonardson

The cluster of gold deposits at the Goldstrike property is located in the Northern Carlin Trend in northeastern Nevada (Fig. 1). At many mature mining camps like Goldstrike, exploration innovation and success may wane with time. In this regard, sufficient exploration drilling was conducted in the area immediately north of the ultimate pit crest and under the final planned pit wall to test for a major deposit. No indications of large deposits were found, however, the majority of drill holes did intercept mineralization. Mining along the northern pit wall exposed significant structurally controlled ore-grade mineralization that had been missed by exploration drilling. In 2002 and early 2003, the mine geology group added reserves to the pit and improved the definition of underground resources by targeting specific ore-controlling structures within favorable stratigraphic units by utilizing relatively inexpensive horizontal RC drilling from the pit wall. The widespread occurrence of mineralization to the north of the pit was re-interpreted to be an indication of continuity of these mineralized zones. In January 2003, 70 feet of 0.332 opt Au at a depth of 710 to 780 feet was intercepted in a dewatering well. This intercept was significantly thicker and higher-grade than average for the area, which confirmed the existence of high-grade structural continuity, and helped secure management support for additional exploration. A timely and cost effective solution was needed to confirm the potential of the area. Immediate follow-up drilling on tighter grid spacing was rejected in favor of improving the geology model. Exploration across the property would benefit from an improved geology model, but to provide results in a timely manner, the area to the north of the Betze pit was chosen as a starting point (Fig. 2).

Jan 1, 2005

By N. Finkelstein, C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble cop- per from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976

By G. Baudet, M. Save

Ethoxylated phosphoric ester surfactants were evaluated as collectors for flotation of carbonates from sedimentary phosphate ores, at slightly acidic pulp pH, using sulfuric acid or sodium fluorosilicate as a phosphate depressant. With 12 to 15 carbon atoms in the hydrophobic chain, maximum collecting power was observed for 9 to 10 ethylene oxide units. Only fine carbonates, ranging in size from about 20 to 160 µm or 40 to 200 µm, were effectively removed with phosphoric ester collectors. Utilization of seawater, or water of extremely high hardness, did not detrimentally affect selectivity. Silica, silicates, and residual fine carbonates can be separated in a second flotation stage, with primary amine as a collector. Coarse carbonates are separated by direct flotation of phosphate with fluoride ion as a phosphate activator and primary amine as a collector. In a seawater pulp, fluoride ion was not required. Typical examples of laboratory and pilot- scale test results are given to illustrate capabilities of the various flotation flowsheets.

Jan 1, 1999

By A. F. Alsobrook

Specialty silica materials, as defined in this chapter, are rocks that consist predominantly of silica (SiO2) and are produced as chunks, round pebbles, and sawed or trimmed blocks and other shapes for nonconstruction applications. The rock types include quartzite, sandstone, novaculite, flint, chert, and vein quartz. Other terms used commercially include jasper, silex, lascas, and rock crystal. In its publication, Minerals Yearbook, the US Bureau of Mines (USBM) reports the production and consumption of some specialty silica materials under several headings. Quartzite, sandstone, and novaculite used in abrasive applications are addressed by the USBM under Abrasive Materials. Lascas, a type of vein quartz used in growing synthetic quartz crystals and in fusing applications, is discussed under Quartz Crystal. Silica gravel used in manufacturing silicon metal and ferrosilicon, as metallurgical fluxstone, and as a filtration medium is covered under Industrial Sand and Gravel. Information on

Jan 1, 1994

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

By Ron M. Canon, John M. Begovich

Chromatography, ion exchange, and other techniques based on the interaction of solutes with solid phases offer versatility, high resolution capabilities, and near-universal potential applicability for the separation of valuable constituents in liquid solutions. The expense associated with obtaining reasonable throughput for these separations has been the only, albeit overwhelming, obstacle preventing widescale use of these methods. Attempts to devise continuous (cheaper) systems have previously resulted in moving, or simulated moving, beds of resin with complicated valving and timing sequences. These disadvantages, plus technical problems associated with the disturbing effects of non-plug flow and reduced resolution of moving versus packed beds, severely limit applicability of these systems. Over the past decade a new device has been developed that overcomes many of these problems. It utilizes a slowly (less than one revolution per hour) rotating annular bed of sorbent material with fixed-feed inlet and product withdrawal points. Numerous units of various diameters and lengths have been fabricated and operated, and a parallel effort has developed a satisfactory theoretical treatment of the device. Several simple control systems have been incorporated to thoroughly demonstrate the simplicity of operation, even for multiple products and multiplecarrier flows. This device has been developed using several metal solutions and has demonstrated its power with some of the most difficult, including the zirconium-hafnium, separations. Design equations are available for sizing units based on simple laboratory data and have been tested for units as large as 18 in. in diameter.

Jan 1, 1985

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By David A. Grisafe

Divided opinions concerning dredging-permit locations and boating uses on the Kansas River in northeastern Kansas led to a study of the recreation potential on the river by a legislatively mandated interagency group (five agencies) that included the Kansas Geological Survey (KGS). In addition, the KGS conducted its own study of the river corridor, encompassing the development, geology, and economic resources of the corridor (Brady and others, 1998). The corridor area is 12 mi wide and 140 mi long (171 river miles). Included in the study was the potential impact of restric¬tions to river dredging. The Kansas River and its floodplain in northeastern Kansas are underlain by Lower Permian and Upper Pennsylvanian limestones and shales. The river and its floodplain are the major sources of sand and gravel for northeastern Kansas, and the limestones along the river bluffs supply crushed stone and building stone. The population of the 10-county area bordering the river has grown by 20% since 1980, and now comprises nearly 40% of the state's population (U.S. Bureau of the Census, 1996). Projections (Floerchinger, 1992) indicate close to 50% of the Kansas population will reside in these counties by 2025, with a continued increase in the demand for aggregates. Factors such as floodplain width, price and availability of land, and overburden ratios tend to favor river dredging on the lower part of the river, and floodplain or pit dredging on the upper portion. The use of alternate sources of sand and gravel such as the Missouri and Arkansas Rivers would increase sand prices due to transportation costs to much of the 10-county area. In 1996, river and pit dredges along the Kansas River supplied more than 3 million tons of sand and gravel valued at about $8 million to northeastern Kansas. As a result of its study, the KGS had concerns with the idea of large recreation zones on the river that excluded river dredging in areas of presently large population and projected population growth. This controversial issue is likely to recur elsewhere.

Jan 1, 1999

By B. Stewart, R. Li

Coal waste materials inhibit the direct establishment of vegetation due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss #1 coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980s with little topsoil resources available for final closure. The refuse was acidic (Total S = 0.38%; pH = 3.6), black in color and high (70%) in coarse fragments. The refuse also had a low water-holding capacity (4.5% in < 2.0-mm fraction). A small plot experiment was established on the refuse pile to evaluate the effects of liming rates (50% and 100% of lime requirements) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from <4.0 to >6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only. This was due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Applica¬tion of 27Mg ha`1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and this appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity of leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile. Therefore, long-term water-treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 2000

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. ng of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

Jan 1, 2008

By William G. Fischer

Equations developed by an early researcher in subsidence, F. Martos of Budapest, Hungary, have been slightly modified to produce effective equations for predicting the time-dependent nature of Green River trona mine subsidence. Following the initial study, a survey was run to check the results twenty years after mining of the area had been completed. The final results were within a few centimeters of the value that had been projected. Mining conditions in the Green River area are ideal for this sort of study with trough type subsidence being the surface manifestation of high extraction underground room and pillar caving operations.

Jan 1, 1986

By George Weinman

GEORGE WEINMAN: Our first group leader for the discussion, "Ups and Downs of Downsizing," wishes to remain anonymous. ANONYMOUS PRESENTER: When George and Jamie asked me to do this, I thought a while about what to say and went through several variations of what I’ll present today. I came up with the title "Ups and Downs of Downsizing." A lot of downsizing has occurred in all of our industries-mining in particular. While this downsizing has gone on there&apos;s no doubt that all of us produced more and more, probably with less and less people and less and less resources. But I contend that there&apos;s also a big downside associated with this. I disagree with a point made in the keynote presentation yesterday, the point being that vendors are bringing new technology to us. I can agree that the major changes associated with equipment and similar items are being brought to us by vendors. But I do contend that there&apos;s an awful lot that&apos;s getting away from us-especially if you factor in the integrated supply or the strategic alliance or the various and sundry related purchasing techniques. I contend that we are missing a lot of, let&apos;s call it, lesser technology; not major equipment changes, but different tools, different techniques for doing things, different left-handed widgets. The integrated suppliers, to some degree, are bringing this to us; but I am concerned about the small guy who comes up with a good idea but deals through integrated suppliers rather than having direct contact with plant people. They&apos;re probably going to go somewhere else and market their wares. That&apos;s what I&apos;m hearing from a lot of smaller vendors. I also think that we are losing a lot of our knowledge base. Every time you shrink an organization somebody leaves. The bottom line: less people. When a person leaves-and I don&apos;t care who he or she is, be it the janitor who&apos;s cleaning the bathroom, the operator, the engineer-when that person leaves there&apos;s some knowledge that goes with that per- son. And sometimes that knowledge is quite valuable. I&apos;ve worked more or less at the plant "low." I can&apos;t tell you how many excellent, viable projects have come from people who said, "Look here. There&apos;s a better way of doing this." And, you know, they were right. Now, maybe they didn&apos;t have the resources or the expertise to develop these ideas into full projects, but they had that basic idea. Someone may say, "Well, if we put a no. 6 skyhook here, so we can lift this particular pump without bringing a crane from 30 miles away ...." No. 6 skyhooks are a bit expensive, but what if we put together a little structural steel here or whatnot?

Jan 1, 1998

By John L. Bolles

The mineral processing engineer must have some knowledge of mineral identification, and the greater his knowledge in this field, the greater will be his potential to do his own specialty well. Most metal-bearing ores and industrial minerals require processing of some kind to produce a salable product or a material suitable for further processing. The types of treatment are many, but each one is aimed at separating a mineral or family of minerals from others. Obviously, then, it is basic to all mineral processing to identify the minerals present in the raw material and in intermediate and final products resulting from processing. Very often the mineral processing engineer will enter planning while exploration of a mineral prospect is going on. He will examine hand specimens, drill cores and cuttings, bulk samples, and materials in place. He must identify the valuable minerals, their occurrence and associations with other minerals, and the identity of diluents or host rock. An exact and detailed knowledge of the raw material will usually suggest the treatment processes that should be investigated in the development of the most suitable scheme for that particular raw material in that particular location. Physical properties of a mineral often lead directly to a process for separating that mineral from others. Some well-known examples of these are: magnetic separations for such minerals as magnetite, rutile, ilmenite; gravity separations for gold, silver, galena. cassiterite; flotation separation for most sulfides; distillation of mercury from cinnabar; and selective dissolution in specific solvents such as halite or sylvite in water, gold and silver in cyanide solutions, copper oxides, carbonates, sulfates and silicates in dilute sulfuric acid. These processes and many others are described in detail elsewhere in the Hand¬book and so it is not appropriate to give details here, except to emphasize that processing is aided greatly by complete mineral identi¬fication. Developing a treatment scheme for a new mineral discovery is an exciting assignment fag the mineral processing engineer, but much more of the usual work relates to quality control in existing plants. Here too, mineral identification is important. Some processing is aimed toward producing an end product which will meet exacting specifica¬tions regarding purity or allowable diluents. In this situation it is vital that contaminants be identified so that the process can be adjusted

Jan 1, 1985

By Andrew Burton, Damian Schofield, Jeremy Noond

This paper will introduce and discuss a range of techniques that utilise new developments in Computer Graphics (CG) and Virtual Reality (VR) for the investigation of incidents and accidents in mining environments. The future of mining safety may not be totally led by the demands of the mine operators, but sometimes by the academics, commercial software developers and legal pioneers who generate new ideas and products and set admissibility precedents which may change the way certain traditional investigative operations are performed. In any accident investigation the outcome from the investigating team is often a complex affair and the results of the investigation are often reported in large, convoluted documents. Computer-generated forensic reconstructions allow investigators to present accident scenarios in an accessible and easily understood, visual manner. Surveys in the US have also shown that people have increased recall of computer-generated images over many other forms of evidence. The AIMS Research Unit in the UK have been pioneering the use of Computer Graphics (CG) and Virtual Reality (VR) technology for both industrial and road traffic accident reconstruction. This paper and accompanying presentation will contain examples of forensic reconstructions developed by the authors that explain some of the methodologies used to ensure admissibility of this type of digital evidence. The paper will contain a number of case studies based on UK and International industrial accidents. The paper will focus on how AIMS Research is extending the capabilities of the accident reconstructions created to take advantage of the latest developments in VR technology. As digital technology makes its impact within professional and commercial fields, computer generated forensic reconstructions will form important admissible evidence in the courtrooms of the future. The technology will also make a great impact in the way we train our workforces, with highly visual three-dimensional (3D) interactive training tools becoming the norm. Acceptance by the public, courts and workforce is an important issue, and implementation strategies must be considered carefully.

Jan 1, 2002

By H. Beecher (Original by) Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation&apos;s water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water&apos; was generally accepted without too much concern for what was in the water since low-cost products and services, rather than clean water, were the public demand.

Jan 1, 1981

By M. Pawlik

Canadian sylvinites contain over 90% of KCl and NaCl and a few percent of water-insoluble minerals. Cationic flotation is used to produce KCl concentrates. Since water-insoluble minerals appear in the pulp as slimes, and since long-chain primary amines are utilized as a collector, desliming is essential. The potash industry utilizes different desliming methods. This may involve selective flocculation of the slimes with polyacrylamide and removal of the flocculated product by flotation, or mechanical desliming with the use of classifying cyclones. Whichever method is applied, desliming is never complete; the flotation feed after desliming still contains about one percent of the slimes which heavily affect collector consumption and flotation selectivity. Therefore, the remaining slimes have to be rendered inactive by “blinding” them with polymers such as carboxymethyl cellulose or guar gum. The commercial blinders used by the potash industry include natural and synthetic polysaccharides. The most common is the use of carboxymethyl cellulose (CMC) and guar gum (GG). These are quite different polymers, while CMC is anionic, GG is non-ionic; while the applied CMCs are of relatively low molecular weight (about 300,000) GGs have much higher molecular weight. Guar gums are also heavily used as the depressants of naturally floatable gangue in the processing of platinum-bearing ores, and according to Harris et al. (1999) quite a large variety of modified guar gums are available in South Africa for this application. Cheng et al. (2002) claim that natural guar gum’s molecular weight is 1.935 • 106. Robinson et al. (1982) found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105. The highest molecular weight sample is then very close to the natural guar gum studied by Cheng et al. (2002). According to the manufacturer, the Rantec KP4000 guar gum which is used by the Canadian potash industry has a molecular weight of about 1.5 x 106. Since both KCl and NaCl are soluble in water, the flotation process is carried out in saturated brine. At 20 oC, 1450 kg of NaCl-KCl-H2O saturated solution contains about 0.300 kg of NaCl, 0.150 kg of KCl, and 1 kg of water (Gaska et al., 1965). Thus, in the saturated NaCl-KCl brine there are about 5.1 kmole of NaCl and 2 kmole KCl per 55.5 kmole of water. This gives 3.9 molecules of water per each ion assuming complete dissociation of NaCl and KCl. Thus, it is obvious that all water molecules in the saturated brine must be bound in the hydration shells around the hydrated ions. The surface tension of the NaCl-KCl saturated brine was recently measured to be 85 mN/m (Laskowski et al., 2003).

Jan 1, 2004