Search Documents

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam rocks and overburden and the prudent selection of mining methods and mine layout designs. Using finite-difference modeling, experience in many U.S. mines and measurements of the pressure arch width, the author has reviewed the engineering design factors that control seismicity in room-and-pillar retreat operations for stiff stratigraphic conditions in deep western U.S. mines. By back analyzing the overburden response in now understood to have been inadequately designed historic room-and-pillar mine, the overburden collapse mechanism is addressed as well as the need for improvements in designs including panel and barrier pillar widths, and sequence of retreat.

Jan 1, 2009

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By W. W. Wen

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an mine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electrokinetic behavior of coals of different rank and degree of oxidation were studied by an electrophoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite was depressed. Comparing the flotation results with the electrokinetic results verified that in the presence of ferrous sulfate, the maximum hydrophobicity of oxidized coal with dodecylamine and frother is near its IEP which is around pH 6.5 to 7.0.

Jan 1, 1976

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala's Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala's cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala's Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976

By Andre C. Zingano

It is a very difficult task to estimate the immediate roof and support behavior in a room-and-pillar mining section in the initial phase of the mining project. There is little information available at this phase, and it is restricted to geomechanic characterization of the rock layers from cores samples, and the in-situ instrumentation of experimental entries and intersections. Even being a pilot excavation for roof support test a good indicator for the behavior of the immediate roof, its behavior for a full excavation mining section is different from a single intersection of two entries, mainly because the stress redistribution caused by the multiple entries excavation and face advance for a full excavation section. The objective of this paper was to calibrate a 3-D numerical model of an experimental intersection, based on the in-situ instrumentation of an experimental intersection excavation, and the geomechanic description of the rock layers. The numerical model was built with the same specifications as the excavation test, including the entry geometry and roof support. The numerical model calibration was based on wire extensometers that were installed at different positions in the roof of the pilot excavation, and on the geomechanic characterization of the rock layers that form the roof, coal seam, and floor. Therefore, it is possible to estimate whether the roof support specification adopted in the test phase will be good enough for the development of the entire mining section.

Jan 1, 2009

As the surface reserves are being depleted, more and more stone operators are seeking underground mining options. Stability of underground openings is a major concern for the safety and productivity. This paper relates to a field study conducted at a large underground limestone mine in Central Pennsylvania. Identification of hazards leading to ground failures and assessment of roof fall risks are important in mitigating injuries. Field observations at this mine were integrated with Roof Fall Risk Index (RFRI) mapping software recently developed by West Virginia University. The system is designed to combine field study data related to geologic factors, mining-induced damages, roof profile, and ground water influx to generate RFRI maps. The mine has adopted a proactive ground control program consisting of comprehensive examination of drilling and bolting logs; precision surveying of roof and rib; accurate mapping of cutters, falls, and geologic structures; and installation of extensometers and microseismic monitoring systems. Investment of time and resources has eliminated fatalities and lost-time injuries due to ground fall. This paper presents the geologic settings, mining conditions, ground control issues along with risk management and control techniques adopted at the study mine.

Jan 1, 2009

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By Aydin Shaterpour Mamaghani, Bilgin. Nuh, Engin Dogan, Tayfun Erdogan

"Improved safety and more environmentally friendly operation are basic advantages of mechanical excavation over the drill and blast method. Raise Boring Machines (RBMs) are one of the types of these machines which have recently been increased use in Turkey. The excavated hole with RBM is more stable than other methods and has better air flow, making it ideal for ventilation shafts. This paper is a summary of the performance of a RBM in the Balya PB-Zn Mine in Turkey. Length and diameter of the ventilation shaft are 200 m and 2.4 m, respectively. The geological and geotechnical characteristics of the strata excavated in the mine are first given and later the validity of a model developed to predict the machine performance is discussed. It is believed that the results of this study and the model given to estimate the performance of the RBM will be useful guide for future applications. INTRODUCTION Raise boring technology was developed to meet the demands of the mining industry, but has also found numerous applications in tunneling or infrastructure projects for ventilation purposes. Raise boring machine uses a small diameter drill rod, around 230-350 mm to drill a pilot hole down to the required depth up to around 2000 m. Once the pilot hole has been drilled to the desired depth, a reamer of up to 9 m diameter is attached to the drill rod. The reamer is then pulled back up to the upper level, creating a round shape. Continues operation provides a faster advance rate than other methods. RBMs are suitable both in hard and soft rock. The flexibility in different angles and diameters is a great advantage compared to drill and blast excavation method. RBM creates a shaft with smooth walls which usually does not require lining. The hole is more stable than a drilled and blasted method and has better air flow, making it ideal for ventilation shafts. Raise boring is convenient method in competent rock; however several problems are faced in geological formations where geological discontinuities are dominant. Moreover, assembly and disassembly time may be long in some cases. The performance and operational parameters of the excavating machine should be predicted prior to starting the excavation operations in order to fulfill the economic requirements of the project. In the light of this fact, the main objective of this investigation is to summarize a case study on raise boring machine performance and suggest a new model based on laboratory test results. First, general description of the mine and project are provided. Then, the physical and mechanical characteristics of the samples taken from project area are discussed. In the third section, performance and operational parameters of RBM are investigated to understand the machine behavior in different rock characteristics and also to collect a useful database for further investigation. In the fourth section, a new model for performance estimation of RBM are recommended."

Jan 1, 2016

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By R. Reddy Kallu

Prior to July 2007, the only accepted method by MSHA for evaluating the mine seal design and performance is the full-scale explosion tests conducted in the NIOSH?s Lake Lynn Experimental Mine (LLEM) for deeming a seal design suitable for use in U.S. coal mines. Since the new regulations came into effect use of these conventional full-scale explosion tests for evaluating mine seals for the new elevated design standards may not be practicable. Generation of such high explosion pressures in experimental mines is dangerous and may cause permanent damage to the testing facilities. Further, they require significant amount of time, labor and money. Considering these factors, there is a need to develop scientific methods for evaluation of new seal designs and for understanding the dynamic seal response. This paper tries to address the reinforced concrete (RC) seal design using the three dimensional finite element based explicit software ABAQUS. Full-scale explosion test data available from NIOSH?s LLEM on 20 psi reinforced concrete seal is used for validating the numerical models. Further in this paper, based on the results from the validation models, a reinforced concrete seal is designed for 120 psi design standard for typical entry dimensions.

Jan 1, 2009

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By S. M. Moore, J. F. Burr, R. Fernando, D. Snyder

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done. As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal. TECHNOLOGY GAPS TARGETED BY THE MINER ACT The MINER Act addressed several technology challenges: • Problems with donning and switching between self-contained self-rescuers (SCSRs). • Poor visibility in smoke. • No wayfinding assistance for escape from the mine. • Limited breathable air supply. • Inability to locate trapped miners. • Inability to communicate with trapped miners. • Failure of mine seals. The MINER Act had several provisions that prescribed specific safety technologies intended to address these issues. Many of these were directed at post-accident technology requirements — an area in which Congress mandated additional technology investment. Specifically, the Act required mine operators to submit emergency response plans (ERPs) that contained provisions for implementing new or improved post-accident communications, tracking, lifelines, refuge alternatives and breathable air supplies along with training for emergency procedures and local coordination of emergency response. Most of the requirements were to be carried out within three years of the ratification of the MINER Act. In addition to these requirements for mine operators, the Act clarified and expanded NIOSH’s role and authority in enhancing the development of new mine safety technologies and expediting their commercial availability. The MINER Act also required NIOSH to develop research on refuge chambers, mine seals and the use of belt air and fire-retardant belts. Mine seals had to be upgraded and MSHA turned to NIOSH for applied research to establish the new explosion-resistance requirements. Progress toward closing the gaps."

Jan 1, 2017

By C. B. Manula

The application of computers to materials handling problems has recently been investigated by various mining groups. This approach has been found, especially useful where a large amount of alternatives must be investigated prior to arriving at a final decision. These alternatives may be expressed in terms of man hours, units and types of equipment such as trucks or conveyors, or the allocation and operation of proposed or existing haulage facilities. The decision problem becomes especially evident when we consider the mechanical revolution which has flooded the mining industry in recent years. The industry has become highly competitive, with the need to keep low profit materials away from high cost production faces ever increasing. The capital investment required for the highly sophisticated equipment that is necessary to perform this function is generally great, and management is faced with decisions which must all too often be made without sufficient data.

Jan 1, 1967

By B. W. Cavender

"World-class manufacturing" (WCM) techniques can be applied in milling operations to substantially improve productivity and reduce costs. Through the use of "just-in-time" and "total quality control" practices, WCM methods establish an environment for continual and rapid improvement in all aspects of production operations, with particular gains in product quality, costs, flexibility, employee involvement, and responsiveness to customers. This paper examines WCM techniques that can be utilized specifically in the mill, and their influence on plant configuration, organization, and scheduling practices; equipment selection and maintenance methods; training; the role of supporting staff; and methods of data collection and analysis.

Jan 1, 1993

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009