Search Documents

By Sigmund J. Sulinski

The following is a progress report on a continuing study being made by the Sanitary District for purposes of developing reliable data for predicting costs and progress on future tunnel contracts. All data available to date on five separate tunnel contracts has been analyzed. All were machine-mined in soft ground, all used steel ribs and wood lagging and finished inside diameters varying from 5'6" to 6'6". Basic data regarding progress per shift, hours mined per shift, hours of downtime per shift, cause of downtime and type of soil mined were reported by the District's resident engineer at the job site. Figure 1, Weekly Mining Report is an example of the form used. Data regarding manpower and equipment used during tunnelling operations was also supplied by the resident engineer during the course of construction. Soil type being mined was verified by the resident engineer during construction, by visual observation, and compared with data listed on a previously prepared soil profile. The soil profile is a graphic presentation of anticipated soil stratas superimposed on a cross section

Jan 1, 1997

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine's collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996

By Allen J. Sobczak, Peter J. Peters

The five tunnel contracts of Milwaukee Northeast Side Relief Sewer System are about 80 percent complete. The tunnels are all excavated for 1.9 meter (6'-0") finish diameter sewers in a variable rock, mixed face, and glacial soil environment. Different contracts were let under two primary types of specifications, performance and prescriptive, which treated aspects of construction, such as primary ground support and groundwater control, differently. Interfacing of design and construction through field personnel allowed the needs of all parties to be met and resulted in savings in time and money to the Milwaukee Metropolitan Sewerage District (MMSD). Interfacing, cooperation and risk sharing allowed resolution of problems such as line and grade variations and potential differing site conditions. It also allowed the parties to pursue constructive changes to construction activities. Thus on one contract prescribed use of compressed air was eliminated, but migration of fines into the tunnels was stopped with filter fabric. Use of an expensive primary support system was dropped, but concern about deterioration of lagging was alleviated by use of special materials.

Jan 1, 1983

By L. E. Baker, M. J. Leck

OSIRIS is a continuous monitoring system for respirable dust which has been specifically designed for mining and related industries. By using the latest microprocessor technology, OSIRIS provides a sophisticated dust measuring system which is a cost effective alternative to regular gravimetric sampling. The system is certified intrinsically safe for use underground. Up to eight underground OSIRIS sensors can be controlled and monitored by a single IBM PC computer located at the mine surface. This computer provides continuous and instantaneous information about the dust concentrations at the sites being monitored. Information is available in tabular and graphical form. The paper gives details of proving trials of the OSIRIS system in some UK coal mines. During these trials, adjacent OSIRIS sensors placed on the same underground roadway cross-section gave virtually identical results. Throughout a good correlation was obtained with conventional gravimetric dust samples. The OSIRIS equipment proved both reliable and easy to operate. OSIRIS was designed and developed by the Safety Engineering Laboratory of the UK Health and Safety Executive. It is now available commercially and is being

Jan 1, 1987

By John M. Marek, David E. Nicholas

INTRODUCTION The purpose of this article is to outline the data requirements for selecting a proper underground mining method and to discuss the general steps taken in selecting that method. Determining the appropriate mining method is an iterative process that continues throughout the life of a mineral deposit. We will discuss the subject from the standpoint of a feasibility study, where a realistic assessment is necessary in order to determine investment merit. The feasibility stage of a project is that point where the drilling program has defined sufficient geologic reserves to consider mining the deposit but little or no underground development has been done. Primary parameters for consideration in choosing a mining method are 1) geometry of the deposit; 2) distribution of grade; 3) rock mass strength for the deposit, as well as the hanging wall and footwall; 4) mining cost and capitalization requirements; 5) mining rate; 6) type and availability of labor; 7) environmental considerations; and 8) other site-specific conditions. Of these parameters, the first four have the most impact on determining the general mining method to be employed.

Jan 1, 1981

By N. B. Aughenbaugh

Compacted, fine-grained soils, often referred to collectively as clays, are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials for these liners include a variety of sand, silt and clay admixtures. These exhibit dramatically different engineering properties when densified. Therefore, it is imperative to adequately assess and characterize any soils being considered for compacted liners. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Because they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners also must include an evaluation of their flexibility. That is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1991

By E. Suoninen, K. Laajalehto, L. Kartio

Efficient separation of pyrite from other sulfides is of great importance for the metallurgical performance of flotation processes. In this work Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) were used to study the surface chemistry of pyrite in depression, activation and xanthate adsorption under conditions of controlled potential. Modifications of pyrite surfaces after treatment with depressants (lime, sulfur dioxide, sodium cyanide) and after activation with metal ions (Cu, Pb) were studied. The principal adsorption product identified on pyrite was dixanthogen whose formation started at about +0.15 V and +0.25 V (vs, SHE) in ethyl and amyl xanthate solutions, respectively. Copper xanthate was formed on copper(II) activated pyrite. Activation mechanism of pyrite by copper(II) salts is likely to be electrochemical where copper occurs as copper(I) on the surface of pyrite. Effective depression is achieved by sulfur dioxide and sodium cyanide. Depression at high pH is due to formation of iron(III) hydroxides. Calcium ions do not affect the electrochemistry but adsorb on pyrite and reduce the surface sites for dixanthogen adsorption.

Jan 1, 1995

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By M. A. Trevits, R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water-bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited number of studies have been conducted that characterize hydrologic changes and also quantify the magnitude of mining-induced subsidence. The US Bureau of Mines (USBM) conducted such a study at a mine site in Greene County, PA. A total of eight water wells were drilled, and hydrologic parameters, such as specific capacity, transmissivity and well yield, were determined both before and after mining. Electronic water-level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1993

By W. J. Adamson

Strategic Data Planning (SDP) is an emerging technique for the analysis and design of information systems. This paper describes the use of strategic data planning in the formulation of a complete integrated set of mining technical systems for the Koolan Island iron ore mine. Applications covered include hydrogeology, geology, mine planning, surveying, quality control, laboratory and mine production recording. Koolan Island is 13 kilometres long and 5.5 kilometres wide at its widest point. Its sole industry is an open pit iron ore mine of 3 million tonnes annual capacity, owned and operated by BHP Minerals. Some of the production is used by BHP Steel International, but most is exported. The orebody is steeply dipping and is mined bench by bench. Outturn grades for run-of-mine product are iron 66.5%, silica 3.0%, alumina 1.0%. Computer systems are run on Data General equipment, currently an MV10000. Computer applications, which are shared across mine sites, are developed and maintained by BHP Information Systems in BHP's Melbourne Office.

Jan 1, 1986

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, A. E. Clark, R. P. Bush, L. E. Schultze

The U.S. Bureau of Mines conducted copper exchange capacity (CuEC) tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the CuEC as a function of Cu concentration, pH, and temperature. Further testing resulted in regression equations expressing CuEC's of Na and Ca montmorillonites and attapulgite as a function of Cu concentration, pH, and the concentration of metal ions which compete with Cu for exchange sites. Using these equations, an analysis was made of the impact each clay could have on overall copper recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of copper from in situ leaching solutions. Copper losses are decreased by the presence of competing ions, and A1 and Mg have the largest impact of those ions normally present in Cu leaching solutions.

Jan 1, 1993

By J. K. Whyatt

A microcomputer controlled data acquisition system has been developed for automatic monitoring of underground instrumentation from a remote location. The system has been used extensively by Spokane Research Center personnel for monitoring rock instrumentation in shafts, drifts, and stopes in hardrock and coal mines, especially where instrument access is limited. Ruggedness was a major consideration in designing the underground portion of the system and it has performed satisfactorily under extreme environmental conditions, including temperatures to 1100 F, 100% humidity, and falling water. The major advantage of the system is that it multiplexes the data from 16 channels through a single twisted pair cable to the receiver, significantly reducing cabling requirements. This receiving station can be as far as 8,000 ft from the instruments without the addition of line drivers. The receiver maintains a data buffer with the latest scans, which is periodical 1 y accessed by a micro- computer, either locally or through a modem, that automatically records and reduces the data. Utilities allow on-site plotting of data and uploading of data to mainframe computers.

Jan 1, 1986

By Mulong Yu, Yosry A. Attia

Beneficiation of high magnesium Florida phosphates requires ultrafine grinding to liberate the dolomite (the main source of magnesium), and a separation process capable of dealing with ultrafine sizes such as selective flocculation. The objective of this study was to investigate the feasibility of separating dolomite from apatite ultrafines by selective flocculation. To achieve this objective, selective polymeric reagents to either dolomite or apatite must be first designed and synthesized. This challenging task was accomplished by carefully selecting complexing/chelating agents which are selective to either the Ca or Mg ionic sites on the minerals, and incorporating these reagents into the structure of long chain water soluble polymers to obtain either selective flocculants (with high molecular weight, MW, polymers), or selective dispersants (with low MW polymers) to either the dolomite or the apatite particles. Synthesis and testing of these polymers on individual and mixed mineral slurries, and on a sample of natural high magnesium phosphate ore, have been attempted and the results are described in the paper. The preliminary results showed encouraging signs for the feasibility of selective flocculation separation of dolomite from apatite.

Jan 1, 1993

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By C. L. Lin

Linear grade distribution measurements determined from polished sections of randomly oriented particles can be used to estimate the extent of liberation for multiphase particles of specified size. Two techniques, optical image analysis and microprobe analysis, have been used to establish linear grade distributions. Both techniques were evaluated and compared using variable grade samples of products from a copper porphyry flotation circuit. The statistical significance of the linear grade distribution data obtained by optical image analysis was assessed. The average chalcopyrite content of these samples, as determined by chemical assay was used to estimate the variance of the experimental procedure. For a given accuracy, the number of particles required to obtain an unbiased representation of the sample was determined.

Jan 1, 1985

By Henry N. McCarl

The New England States form the most northeastern portion of the continental United States and include Connecticut, Rhode island, Massachusetts, Vermont, New Hampshire, and Maine. These states have an aggregate population of over 10.5 million people, and an average annual population rate increase of about 1.3%. A great deal of new construction is required each year to meet the increasing demand for new homes, roads, offices, factories, and warehouses. Yet, prices of construction materials such as blocks and concrete are generally higher in New England than in other well populated areas of the United States. This is an indication of local demand being somewhat greater than supply, an atmosphere conducive to new developments in the production of construction materials. One such field of development is the rapidly growing Lightweight Aggregate Industry. Recent construction in Boston has used a great deal of lightweight aggregate. New structures using lightweight aggregate in lightweight concrete include the following: M.I.T.'s 20-story Earth Science Center and 17-story Married Students Housing Project Prudential Life Insurance Center, West End Redevelopment Project at Charles River Park, Hotel Americana, and the British-owned 33-story office building at 50 Pearl Street.

Jan 1, 1964

By John S. Cummings

In this paper the phrase "exploration for blind metal deposits" refers to exploration activities geared to the discovery of metal deposits which cannot be located by visual surface inspection. The word "system" refers to all of the components (people, money, corporations, techniques, etc.) which collectively result in an exploration process. The details of the system or systems which I have employed in exploration will not be discussed because of client relationships. However, some of the more severe problems in exploration result from how the system's components interact and our attitudes as to what exploration data is telling us, if anything. It is these items which will be discussed. Exploration for blind metal deposits, which has been relatively intense over the last 2S years compared to rather minor outlays prior to World War II has often been an uncoordinated assortment of various specialists employing various techniques (see Dickerson -1). In a program geared to the location of blind deposits, the lack of outcropping deposits or occurrences should not be a deterrent to a well conceived and well planned program. The severe cyclical swings in exploration activity, although often coinciding with depressed metal prices, by and large result from the failure of exploration operators to present a coherent and realistic program to management. It is my opinion that the stream of complaints criticizing management for cyclical exploration support are mostly unwarranted, as many of the programs and goals are ill defined. Although depressed market conditions may serve as the catalyst for exploration cuts, the underlying cause is that when the "chips are down", the non-directional, non-specific nature of many programs is revealed. Thus management should not be castigated for eliminating such programs during bad times, but rather they should be castigated for supporting them during boom periods.

Jan 1, 1978

By M. R. Lastra

Island Copper Mine began gold recovery Tom molybdenum sulfide concentrates in April, 1985. Plant design capacity is 20 tons of molybdenum concentrate per day. The molybdenum concentrate is produced in a conventional copper/molybdenum flotation circuit by selective copper depression. After thickening, the molybdenum concentrate is leached with cyanide solution in a series of five leaching tanks. The leached concentrate is then filtered and soluble gold values recovered on activated carbon with a six column adsorption circuit. The gold leach extraction is approximately 80 percent with a gold adsorption on activated carbon of 97 percent.

Jan 1, 1986

By H. Polat

Relatively large amounts of such hydrocarbons as fuel oils are often needed in flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promotors. The reagents which are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Since the physical and chemical variables influence various sub-processes in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promotors. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1997