Search Documents

By H. Soto

As a follow-up to a laboratory study, a pilot scale column for the flotation of coarse particles was designed and then tested in two different applications. In the first test, the concentration of a coarse phosphate ore (normally beneficiated by skin flotation in spirals) was carried out in a flotation plant in Florida. In the second pilot test, the column was used as a scavenger cell in the coarse flotation section of a potash beneficiation plant in Saskatchewan, Canada. Particle size of the phosphate feed was of the order of 0.6-1.0 mm and the potash feed 1-3 mm. The column was 1 feet diameter and was fed at rates between 0.5 to 1.4 tph. The effect of operating variables such as air and water flow rates, bubble size, frother concentration, residence time, sparger, etc were evaluated. The most important factors in column performance were found to be bubble size, air flow rate and the thickness of the froth bed. Best results were obtained in the absence of a froth bed, with low air flow rates and with small bubbles. The paper presents comparative performance and discusses details of the column design. Phosphate recoveries in the column were better than 90% whereas the conventional skin flotation circuit normally yields about 60% recovery for a comparable concentrate grade. Potash recovery from the tailings of the conventional flotation circuit was as high as 42% recovery. Particle size distribution of the potash concentrate was coarse enough to meet requirements for potash fertilizer.

Jan 1, 1993

By S. G. Axen

Design of wells for in-situ leaching is based on individual mining operation and ore deposit requirements. Major design considerations are well flowrate, depth, fluid composition, expected well life, mine operating plan and cost. A large variety of downhole equipment, materials of construction, contract services and methods of well completion and stimulation are available. A generalized design procedure which allows the engineer to optimize well design for a particular ISL application is described.

Jan 1, 1988

By Norbert Patzelt

Today the standard method for grinding ore is the wet process. This is mainly due to the fact that the downstream process is wet and considering the total circuit dry grinding is not the most eco­nomical method for the comminution of the ore. Presently in gold ore processing dry grinding is only applied in cases where whole ore roasting is required downstream from the milling plant or if organic carbonaceous matters and sulfides are the primary reasons for the refractoriness. Since dry ore can be fed to the roaster, a dry grinding mill can advantageously be applied. In cases where d1y grinding could be applied advantageously for instance if the ore contains water soluble material and wet grinding is not possible there are serious concerns prevailing within the industty against this technology due to several reasons. Besides of the aspects as discussed later in this paper, there are several plants in operation with little success and considerable operational prob­lems. The reasons for this often lie in the fact that the several com­ponents of such a plant are bought from independent sources with­out considering the system requirements. It is essential that the dry grinding plants require accurate design between drying, pneumatic transport and grinding of the ore in the circuit. This paper will address some of these concerns raised in the industiy from a mill vendor's view along with discussing the development for the selection and configuration of the various dty grinding circuits.

Jan 1, 1998

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

By E. R. Hoskins

The Gulf Coast States ranging from South Texas to Alabama contain vast resources of lignite ranging in energy content from about 4000 to 7000 Btu/lb (as-received) with sulfur content ranging from about 0.5 to 2 percent. Currently, the strip mining rate is about 35 million tons per year in Texas and essentially zero in the other Gulf Coast states. Estimates of future mining rates are as high as 310 million tons per year by the year 2000 with 240 being in Texas. In this paper, we examine the life cycle of the surface mineable lignice based on the most recent estimates of surface mine recoverable resources with two scenarios. The first indicates that a 310 million tpy rate could be sustained for only 15 years while the second scenario suggests that the 310 million tpy could be sustained for 25 to 30 years. If lignite resources are required beyond those that are surface mineable, the deep basin lignite will be developed. Five strategies for developing deep basin lignite are discussed.

Jan 1, 1983

By K. Anim, C. Calderon-Arteaga

Located in Mojave, CA, The Soledad Mountain mine is an Open pit Heap-Leach gold Mine, which is operated by Golden Queen Mining Company LLC. under private capital. Open pit mining began in 2015 while full production was reached in 2016. The open pit mine feed a processing plant that can process more than 13K tons per day of ore which is sent to a heap leach pad. The Soledad Mountain project is a poly metallic deposit with Au and AG being recovered as payable metals. As the mine became bigger after moving to the east pit phases, Golden Queen was facing new challenges to control the production and accurately determine KPIs to improve/increase the production. To maximize returns and asset value, a new fleet management system (FMS) was adopted and implemented. The new FMS has enabled the mine to interconnect the different stages of the mining, as well as to recognize issues and implement the necessary corrections. With the associated increase in complexity in the process, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery. Implementation of new daily and weekly plans were needed to ensure the ore delivery and meeting the tonnage goals, while allowed the equipment operators to better geolocate and to maximize the equipment production. These conditions alongside with Golden Queen’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route the material from the mine, is critical to site success and some of these challenges have been overcome by the adoption of the new FMS, the implementation of daily and weekly plans and upgrades in the ore control workflow. Examples of how the integration of the new systems allowed golden Queen to improve production strategy, are discussed in this article.

Mar 2, 2022

By Ryan Dr.

In December 1988 Phelps dodge corporation brought an underground gold mine into production in the republic of Botswana. The mineralization is associated with steeply dipping shear zones in Archean greenstones of the Tati Schist Belt. The gold is intimately associated with sulfides and is refractory in nature. The deposit is being exploited by underhand open stoping methods. Vertical and inclined shafts are used to hoist the ore to surface where it is treated by conventional crushing, milling and flotation, followed by fluid bed roasting with CIP elution and carbon regeneration. Adjacent deposits are being explored with a view to increasing production. Legal and taxation aspects of operating in Botswana are discussed.

Jan 1, 1989

By Arnold Dix, Oliver Heger, Bernhard Kohl

In the USA, risk-based decision making has not been a common approach to tunnel safety in the past, but this is changing, as concepts such as “equivalency” in the NFPA 502 framework gain acceptance in the USA and elsewhere. In other regions, in particular in Europe, risk assessment techniques have been used for nearly two decades in many jurisdictions as an additional tool to complement the application of prescriptive guidelines and support decisions related to tunnel safety. After some initial difculties these methods are meanwhile a well-established element of tunnel safety management. There are several tools available which have been practically applied and further developed over years, such as the Austrian tunnel risk model TuRisMo, or the PIARC owned DG-QRAM model. Whereas TuRisMo is a holistic, system-based model, which is best suited to quantify and assess re risk and associated mitigation measures, DG-QRAM focusses on the risks related to the transport of hazardous materials. Depending on the objectives and the scope of the investigation and the regulatory environment tunnel risk assessment tools are in use for different purposes, mainly to demonstrate a sufcient level of safety and to decide on and select additional risk mitigation measures. The international eperience substantiates that the general approach is eible and that the methods and tools are mature and can be applied for different problems in different environments. First case studies like the risk study on conditions and permissibility of the transport of hazardous materials through the Eisenhower-Johnson-Memorial Tunnel in Colorado demonstrate the applicability of a risk-based concept for decision making in the US-American environment.

Jun 23, 2024

By Michael Bourassa, Sonja Felderhof, Normand Champigny, Steve Vaughan

Introduction -Comparison of International Reporting Standards (Sonja) -Legal and Due Diligence Requirements for Reporting (Steve) -Flexibility to Recognize International Reporting Standards (Michael) -Obligation of SRO’s to Discipline (Michael) -Impact of Sarbanes Oxley on Reporting (Normand)

Jan 1, 2003

By J. C. Emerick

Preliminary investigations have shown that wetland-based treatment systems can be an effective and relatively inexpensive control strategy for mine drainage pollution in eastern coal mining regions. This strategy also has potential for western mining regions, although too few systems have been installed in the west to permit general evaluation of the concept for western climates. The construction of prototype systems is encouraged for some situations. Wet-land environments have the capability of removing metals by natural geochemical and biological processes, including precipitation, filtration, ion absorption, and biological uptake and accumulation. Data presented for natural wetlands receiving mine drainage show removal of iron and other metals, and high accumulation of metals in soils and plants.

Jan 1, 1988

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By O Gutsche, Fuerstenau D. W., R. Ravikumar

Six minerals and one ore, namely, barite, dolomite, galena, limestone, quartz, quartzite and taconite, were ground in single-particle comminution mode in a rigidly mounted roll mill with different levels of energy input. Grindabilities were determined from the median size of the self-preserving product size distributions, which was taken as a measure of the fineness of the ground material in an empirical energy-reduction ratio relationship. These values reflect the inherent resistance of the solids to mechanical size reduction that are least distorted by particle-particle interference effects, grinding characteristics, energy efficiency of the milling system employed and the extent of the fineness specified.

Jan 1, 1992

By D. Carr, C. Anderson, M. Deal, C. Larson

"Construction of the OceanaGold Haile operation’s process plant in Kershaw, South Carolina is currently under way, with ore through the mill expected in late 2016 and commercial production expected in early 2017. The process is designed to treat 6,350 tonnes per day with minor upgrades required to achieve 8,270 tonnes per day. Plant optimization during detailed engineering, combined with a focus on de-risking the process, has resulted in numerous process changes since the initial design. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio operation, whilst identifying potential expansion opportunities. INTRODUCTION Haile Gold Mine is located in Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching from 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that delineated 2.02Moz. of gold in reserve at an overall grade of 2.06 g/t. OceanaGold acquired Romarco Minerals and the Haile Operation in October of 2015. OceanaGold operates under a risk management philosophy in all aspects of operation, both corporately and at each individual business unit, and has implemented numerous process changes to eliminate or mitigate risks identified in the initial design of the processing circuit, and provided increased opportunity for optimization and expansion. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio Operation, and identifies potential expansion opportunities. INITIAL PROCESSING CIRCUIT DESIGN An extensive metallurgical test work program was undertaken by Romarco Minerals and third party laboratories during the initial design phase of the Haile project [1]. This preliminary test work provided the technical information as a basis of plant design. The initial flow sheet for the Haile processing circuit is shown in Figure 1 (see APPENDIX). The plant is designed to process 6,350 tpd (7,000 stpd) on an annualized basis. The process begins with a jaw crusher followed by a SAG and ball mill grinding circuit to reduce particle size to P80 74 µm. A flash flotation cell treats 50% of the cyclone underflow in the ball mill circuit. Grinding circuit product is sent to a rougher flotation circuit to recover gold-bearing pyrite. The flotation concentrates from flash and rougher flotation are reground to P80 13 µm using stirred media detritors (SMD’s). The rougher flotation tail is pumped to the carbon-in-leach (CIL) circuit for gold recovery. The reground concentrate is pre-aerated prior to being pumped to the CIL circuit. The CIL circuit is a hybrid circuit with eight tanks. Tank 1 leaches the pre-aerated concentrate only, and tanks 2 through 8 leach the combined flotation tailing and tank 1 discharge. The carbon strip circuit is a standard pressure Zadra system, followed by electrowinning, and refining using an induction furnace. CIL tailing passes through a cyanide recovery thickener prior cyanide destruction and then pumped to the tailing storage facility (TSF)."

Jan 1, 2017

Iron ores may be upgraded by flotation of iron oxides or siliceous gangue using either cationic or anionic collectors. The electrostatic mechanism of adsorption can account for the complex chemistry involved. In industrial practice, only cationic silica flotation is used at present in North America. Some of the seemingly paradoxical phenomena of cationic silica flotation behaviors in meeting the demand for low silica concentrates are reviewed.

Jan 1, 1989

By C. B. Manula

The total systems model for underground coal mine planning and design (Master Design Simulator) is a set of computer programs which encompasses a realistic reproduction of the interaction among the geological, environmental, equipment, methods, and the health and safety aspects of the mining plan (Manula, Rivell, and Ramani, 1975). The total system includes nine major subsystems: geology and reserves, methane generator, roof support, subsidence, production, rail haulage, cost, water generator, and ventilation (Fig. 1). The subsystems themselves are divided into two categories based on the frequency with which they are executed: (1) event-oriented subsystems are executed either independently or at discrete intervals when certain specific events occur; and (2) dynamic subsystems function interactively during the production cycle, transferring data to or requesting data from event-oriented subsystems only when specific events occur (Fig. 2). Each subsystem has been tested and validated independently (Ramani, White, and Sutton, 1974; Ramani and Owili-Eger, 1974; Manula, Mozumdar, and Jeng, 1974a; Manula, Mozumdar, and Jeng, 1974b; Manula, et al., 1974; Manula, Rivell, and Sanford, 1974; Ramani, McClay, and Burgos, 1975; Manula and Owili-Eger, 1975; and Ramani, Owili-Eger, and Manula, 1975).

Jan 1, 1979

By Jean-Luc Cornet

Advances in conveyor technology over the past decade have enabled the design and erection of very long overland belt conveyors. Such conveyors usually require head and tail drives to lower the belt tension and belt strength required. This paper provides an overview of the problems encountered in controlling the head and tail drives on such conveyors and some of the solutions developed by CDI for several such projects.

Jan 1, 2002

By III Cocanour

The line scan video photometer is a personal computer (PC) based, software-driven instrument which is used for the real time, on-line analysis of industrial process streams. The novelty of the instrument lies in the integration of its various components: (l) a true Red/Green/Blue (R/G/B) color video camera; (2) a unique, line-scan color sample and hold technique which provides a 4 to 20 mA analog signal to a commercial 12 bit analog to digital (A/D) converter; (3) software which converts data through a color absorbance algorithm to correlate elemental color to concentration; and (4) software-based control which utilizes color data, along with temperature and conductivity data to control process equipment. The photometer can be used for noninvasive analysis wherever color hues are representative of process variables such as chemical concentrations or mineralogy color reflectance. The line scan video photometer has been successfully demonstrated in solvent extraction/electrowinning (SX/EW) and ball mill circuits of copper producers.

Jan 1, 1996

By L. J. Altenburg

There are a lot of key factors involved in achieving a successful Safety Program. I would like to discuss some of these factors and how they have played a major part in our success at Jacobs Ranch Mine. The areas I will cover concern: 1) Facility Standards (Corporate/Minesite), 2) Communication (Employee/Management -"Teamwork"). 3) Proper Training (Employee/Management). 4) Employee Attitude. 5) Incentive Programs. 6) Health Programs. 7) Results/Benefits.

Jan 1, 1994

By P. F. Mataich

When the subject of plant computers is brought up most people visualize the computer&apos;s controlling the entire plant with very little operator intervention. Actually, this picture is true today in only a limited number of cases and will certainly not be true in the minerals industries for many years to come. There are several ways in which a plant computer can significantly contribute to improving plant operation and closed loop control is only one of these. First of all, what are the basic ingredients for good plant control? For good plant control, two requirements must be met. First, the operator must get good information feedback from the process and then he must know what action to take in response to this information. Control information can be obtained through instruments, laboratory analyses, or through simple visual observation. If it is timely and accurate and the operator knows how to use it, then we have the makings of a good plant control system. The computer can be of help in both these areas by getting good data back to the operator and in helping to develop a good control scheme for the plant.

Jan 1, 1966