Search Documents

By Thomas P. Meloy

Theoretical development of comminution models has come about in the last 10 years. These models assume that the material being broken is homogeneous and that the compression or energy wave is uniform throughout the specimen. Obviously, this is not the case because most comminuted materials are rocks with either many phases and/or definite grain size. The mathematical models deriving the size distribution of daughter fragments resulting from the comminution of brittle, single particles are of two schools. The first model, proposed by Gilvarry in 1961, was based on the concept of volume, surface, and edge flaw activation. The second, proposed by Meloy in 1960, was based on the concept that the crack density is a function of the energy in the comminution wave. The flaw theory has run into increasing theoretical problems and is now being abandoned. On the other hand, the crack density theory has been expanded and has successfully considered the case where there are inhomogeneities in the comminutive wave. However, the main constraint of a homogeneity in the solid being comminuted has hitherto never been overcome. In this paper, a very general derivation of the crack density model is made for inhomogeneous solids by replacing the assumption of homogeneity with an arbitrary function, P(y), which describes the susceptibility of the material to comminution as a function of position. The restraints on this function, P(y), are very broad and, hence, the derivation is extremely general. General use of the equation derived necessitates a detailed a priori knowledge of both the fracture process and of the physical properties of the material being fractured; this knowledge is expressed in open form as, P(y), the linear probability density that a plane of fracture intersects at point y on an arbitrarily oriented line segment of total length xo through the original particle. From these assumptions, a general expression for the cumulative mass distribution of particles resulting from fracture is then postulated. It is: [ ] where, B(x), is a cumulative mass of material finer than size x, r is the average number of crack,, (y), is defined above and xo is the initial particle size. It is shown that suitable assumptions reduce the expression to the theoretical results of Gaudin and Meloy and to special forms of the empirical equations of Rosin-Rammler, Gaudin and Schuhmann. Semi quantitative agreement is demonstrated by Grimshaw with experimental results of a very complex fracture of heterogeneous sandstone blocks. A need is expressed for more theoretical development of P(y), and a more extensive experimental study of both homogeneous and heterogeneous fracture. The full mathematical derivation is presented for the first time in this paper. The general implications of the equation and its application are also discussed.

Jan 1, 1968

Fossil resin types occurring in the Hiawatha seam of the Wasatch Plateau coal field, Utah, have been separated according to color and their physical and chemical properties evaluated. These resin types were separated into four color fractions, yellow, amber, light brown, and dark brown. Each resin type has then been subjected to comprehensive spectroscopic examination and other physical methods of characterization. Included among the spectroscopic methods of characterization are FTIR and 13C NMR spectroscopy. Physical properties that have been measured include density, optical, and magnetic properties. These analyses reveal that the resins are distinct from other macerals, predominantly nonaromatic in nature with small amounts of oxygen functionalities and a low degree of unsaturation. The four resin types show distinct differences in certain physical and chemical properties such as density, hexane solubility, magnetic susceptibility, and aromaticity.

Jan 1, 1990

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Jan 5, 2023

By J. Hilgers

Metal prices are often predicted by relying on time trend projections of various economic indicators or even the trend in price itself Thus, time is the underlying explanatory variable acting through at best, a limited selection of economic variables. The price prediction method described in this paper differs from this by analyzing hundreds of economic variables to develop a few principle components that automatically capture the fundamental changes in the economy and delete duplicate or irrelevant information. This leaves a few principle variables to describe a state-space representation of the economy which can then be used for prediction. Forecasts of the price of a metal are then made based on these principle variables.

Jan 1, 1995

By Felicia F. Peng

Using a fuzzy logic controller, a signal applied on the processes may be generated through a linguistic protocol expressing an operator's intuitive control strategies. In this work, fuzzy logic controller and PID controller imposed upon the feedback liquid level control systems for a stirred tank are studied and compared. The construction factors including the shape of membership functions, number of fuzzy variables, number of inputs, number of rules, and different defuzzification methods are considered in design and formulating the fuzzy logic control strategies and algorithms. From the analysis of the strategies and control performances, an optimum controller may be generated by making use of the best combination of these fuzzy construction factors.

Jan 1, 1997

By G. K. Wilson

This paper will discuss some of the more important aspects to be considered when selecting pumps for mill discharge, cyclone feed or other severe-duty applications Included will be the selection of the pump based on such factors as particle size, particle distribution, head, flow, temperature and pH Other specifics to be covered: The relationship of impeller speed, head and wear factors as they affect pump performance and wear life; the importance of selecting a pump whose performance curve best suits the application; and how the addition of service factors applied to the actual operating conditions can lead to severe operational problems such as premature wear, pump running out on curve, and exceeding horse power limitations.

Jan 1, 1996

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

By M. Westerstrand

It is known that the water chemistry of the process water during ore refinement can affect product quality, such as iron pellet strength. The main objective of this study was to quantify the amounts of major elements, such as Ca, Mg, Na, S and Cl carried by process water and by magnetite grain surfaces to the end product, iron ore pellets made from magnetite ore from the Kiirunavaara Mine in northern Sweden. In addition, the amount of colloids (0.22µm ? 1kD) in the process water was examined by ultrafiltration. The amounts of various elements sorbed to the magnetite surfaces were estimated by leaching with Milli-Q water, MgCl2, NH4-acetate and Na-acetate. Total dissolved solids were between 1,446 and 1,775 mg/l, dominated by Ca, S, Na and Cl (89%). The colloidal fraction was less than 3% for major ions. For Ca and Mg, sorption to magnetite surfaces was a much more important transport mechanism for the pelletizing process than evaporated process water, but for Na, Cl and S process water was an important carrier.

Jan 1, 2010

By L. D. Patts, S. J. Janisko, E. G. Cauda, A. D. Bugarski, G. H. Schnakenberg, J. A. Hummer

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on the performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for DFEs when the engine was operated at high-load modes rather than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on the total concentration of nitrogen oxides (NOX) were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes..

Jan 1, 2011

By Robert M. Cox

A thorough geological engineering investigation is required before surface lands overlying abandoned underground mines can be safely recommended as building sites. The major problems confronting the geological engineer are assembling accurate geologic and mining information and developing an accurate rock mechanics model of the situation. A successful investigation requires a combination of technical expertise in rock mechanics and engineering geology tempered with practical engineering judgment. The results of a good study are not always favorable to the prospective builder.

Jan 1, 1975

By Mahmoud Sepehrmanesh, Verya Nasri

The purpose of this paper is to outline the advantages and disadvantages of single tube and twin tubes for subway systems. Different aspects such as diameter of the tunnel (tunnel spaceproofing), configuration of subway line and stations, impacts on passenger safety and evacuation, ventilation system as well as rail system for each solution were evaluated and compared. In addition, a multi-criterion approach is established to facilitate the decision making for these two different subway systems. The practical example of a mega project has been discussed and the details of the decision-making process has been explained. This proposed multicriterion can be used to facilitate selecting the best subway system in any urban areas.

Dec 1, 2022

By T. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with pre-benching or serving as the primary stripping tool, dozers can play an important role in driving down mining costs. This paper reviews the application zone of track-type tractors. In addition, it provides tips on site set-up, equipping of tractors, and machine operation which the audience can take home and apply.

Jan 1, 1996

By W. N. Hamilton

British Columbia is geologically favourable for a rich variety of industrial mineral occurrences. Some have been produced for years, others overlooked until recently. Major production occurs for asbestos, gypsum, limestone, magnesite, silica and sulfur; lesser production for a dozen others. For several of the minerals, potential is much greater than existing production. New production opportunities exist also for diamonds, niobium and REE minerals, fluorspar, kyanite, nepheline syenite, talc, and several others. Alberta, though geologically less diverse, also has many industrial minerals. Limestone, salt and sulfur have the major production; clay and shale, silica, sodium sulfate and a few others lesser production. Opportunities exist for expanded production, and for new production in heavy (Ti -Zr) minerals, formation brines (Ca-Mg-I-Li), and gypsum.

Jan 1, 1987

By R. J. Sterrett

To the average mine operator, the implementation of environmental regulations are viewed as a drain on the profitability of the mine. Since the birth of environmental awareness in the late 1960's, which led to the passage of the National Environmental Policy Act (NEPA) in 1969, and through the publicity brought about by the discovery of Love Canal in 1978, the public are clamoring for increased environmental protection. It should be emphasized that the concern regarding the issues of the handling and disposal of nuclear and toxic wastes is not limited to a few overzealous environmental advocates. Toxic waste issues have "grass roots" interest and support. A reflection of this support has been the passage of key pieces of federal legislation. . Of particular interest are the following acts: Clean Water, Toxic Substances Control, Surface Mine Land Reclamation, the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The last act is often referred to as "Superfund". Both RCRA and CERCLA have been re-authorized and amended, and in their re-authorization they have been substantially strengthened. Of the last two pieces of legislation, RCRA is the most powerful in that it governs the handling of hazardous wastes from "birth to grave". CERCLA was established to cleanup abandoned waste sites which are threatening human health or the environment. These cleanups can be undertaken by the government and then billed back to the previous owners or to the disposers at the sites.

Jan 1, 1988

By K. Komnitsas

This paper presents the main environmental assessment techniques and indicators that can be used a) for the establishment of a sustainable development framework and b) for the evaluation of the environmental performance within the mining sector. Reference is made to techniques as environmental risk and impact assessment, life cycle assessment, cost benefit analysis and best practical environmental option assessment that can be used as tools to assess environmental impacts of processes, activities and products in the mining sector. In addition, the issue of environmental indicators, covering operational, management and environmental areas, that provide valuable information regarding both the environmental performance of a mining company and its efforts to influence this performance towards sustainability is discussed.

Jan 1, 2003

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By Randall D. Peterson

Economic operation of a mine ventilation system must include some means by which operating costs can be quantified and evaluated periodically. Current practice at most mines relies upon the best judgement of foremen, engineers and managers to identify high cost or problem areas in the system and to estimate potential costs and benefits of work proposed to reduce inefficiencies. The problem with this is that significant savings can be overlooked or sub-economic projects may be undertaken when sufficient attention is not paid to the interrelationship between airflow characteristics and corporate financial criteria. In order to accurately determine costs and benefits it is necessary to view the solution of each potential ventilation problem as a separate economic opportunity.

Jan 1, 1993

By G. Belardi, N. Sheau, P. Plescia, F. Veglio

A study was conducted to assess a new wet gravity-separation machine, identified as the Multi-Gravity Separator(MGS). Chromite fines, obained from an Albanian chromite and olivine ore and containing 23% Cr2O3 and 18% SiO2, were used in the study. The first step was to determine the influence of various operating parameters. The study indicated that the most important variables for the MGS are rotational speed, tilt angle and shake amplitude. The best treatment conditions for the ore were then identified by investigating a series of circuits designed to produce a marketable product. In open circuit, a concentrate containing 50% CI-203 was obtained with a recovery of 72%.

Jan 1, 1996

By W. W. Roepke, B. D. Hanson

A major problem facing the coal mining industry today is the need to meet more stringent dust standards due to quartz. When secondary suppress ion is not adequate, the time-consuming and costly cut-and-try method of modifying the mining machine is used in the hope that it will reduce dust generation. The Coal Cutting Technology Group, at the Bureau of Mines' Twin Cities Research Center, has developed an inter-active computer program for drum- type cutting systems to help identify, in advance, modifications that offer the best potential for reducing dust. The program, Relative Dustiness Indicator (REDI), evaluates machine dimensions, seam characteristics, and operator-controllable variables for dust generaton, energy, forces, and product ion.

Jan 1, 1986

By Don U. Deere

The tunnel boring machine (TBM) can be a magnificent tunneling device under optimal rock conditions. Such ideal conditions would include good Rock Material Characteristics (compact, uniform; low to medium strength, hardness, and abrasiveness); good Rock Mass Characteristics (few joints and shears; unweathered); and good Geologic Environmental Characteristics (above groundwater level and moderate in-situ stress). Such idealized rock conditions would eliminate support problems, fallout at face and grippers, frequent cutter changes, and water problems. Daily advance rates of 50 m would be commonplace. Unfortunately, nature seldom provides the ideal geologic characteristics. The challenge to the geologist, machine manufacturer, and contractor is to provide equipment and procedures to best handle the adverse geologic features, once identified.

Jan 1, 1981