Search Documents

By Richard A. Bideaux

Using computer applications to solve mining problems began in the early 1960s, utilizing the large (for that day) centralized computing facilities at a few universities and major mining company headquarters. Many years passed before technology was adequate to allow any of those applications to be run at the mine sites to provide immediately available solutions. One of the first mining applications attempted was for ore reserve analysis and long- to medium-range mine planning. As these are among the most frequent and familiar minicomputer applications at the mine site, it is interesting to follow the evolution of computing and communications hardware which has finally allowed effective transfer of this technology.

Jan 11, 1981

By C. Tsiouvaras

Restoration of bauxite mining areas constitutes a difficult issue to address due to the destruction of the vegetation and soil decay of the excavated area. In this study woody species growth, in relation to altitude, heavy metal concentrations and mechanical texture of the underlying mining waste, were investigated. The research was implemented on restored sites of a bauxite mine in the Fokida Prefecture of Greece. These sites were located in three different elevations and the restoration took place in two phases, in 2001 and 1996. Heavy metals measurements showed some correlation among the different metals, whereas their concentration was also associated with plant growth parameters.

Jan 1, 2007

By R. L. Urie, L. Burdzinski

Non-operational mine facilities are subject to placement on the EPA's National Priority List (Superfund). Once a mine site is undergoing investigation and/or remediation, MSHA regulations for health and safety may no longer be applicable. This paper addresses the changes in the applicable and relevant standards that apply to health and safety and public health related to site contaminants. The implementation of health and safety plans, and the development of public health risk assessments are described. Examples are presented from Superfund activities at the Eagle Mine, near Minturn, Colorado; the Anaconda Smelter near Mill Creek, Montana; California Gulch near Leadville, Colorado; and Bunker Hill, Idaho.

Jan 1, 1991

By Daniel L. Hanson

This paper presents case histories of the construction of four large diameter circular shafts using reinforced concrete ring beams as the primary internal support system. The case histories pertain to concrete ring beam systems which have been successfully used in shafts up to 130 feet in diameter and 75 feet deep. Soldier pile and lagging, and driven steel piling earth retaining systems using ring beams, are discussed together with the cost savings associated with using concrete ring beams. Soil conditions encountered at the case history sites are discussed together with the development of design criteria for each shaft. Instrumentation data obtained at one site are also presented.

Jan 1, 1987

By J. J. Gusek, T. C. Richmond, R. W. Reisinger

A high-altitude (9,500-ft [2,900-m]) historic underground copper mine in Wyoming discharges neutral but copper-laden water into a pristine creek. Under a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) deferral agreement, the Wyoming Abandoned Mine Land Program performed site characterization and treatment studies in preparation for reclamation of the site. An integral part of the project included addressing the needs of a variety of interested and affected parties, including property owners, local populations, government agencies, and the media. This paper discusses an overall approach and specific methods employed to enlist public support for the project as well as some of the successes and failures experienced.

Jan 1, 2004

By S. R. Clark

"INTRODUCTION Of all the natural resources being taxed by the needs of the modern world, perhaps the most important is the continually expanding demand for water resources. As water becomes scarcer, and increasingly important, new technologies are needed to find innovative ways to preserve this precious resource. In Chile, for example, the mining industry is investing billions of dollars to build desalination plants and pipelines; bringing ocean water as far as 200 kilometers inland to meet their demand and maintain operations. It is a full-blown crisis for that nation and a top priority for their government and economy. It has been reported that world water consumption will increase by 40 percent in the next 10 years, representing nearly exponential growth. In the U.S., as more and more communities continue to be built, more drain on the current water infrastructure is created. For 25 percent of people and operations that rely on water from aquifers, this source is being consumed at a rate that will create significant problems meeting the demand in as few as two generations.1 A PROACTIVE APPROACH When it comes to controlling dust at your operation, whether a landfill, a transfer station, a haul road or another ancillary area, what are the options? We know watering is not the answer, but at the same time, we need to prevent dust from flying to ensure a safe environment and keep our skies clear of pollution, for both regulatory requirements and neighbors. Creating a Dust Mitigation Program instead of looking to buy the first dust control product off the shelf is a first step to conserve water and, at the same time, maintain the operational demands and environmental standards for a given site. The program concept is straightforward enough. However, the process of effectively constructing and executing a program is quite involved. When undertaking a program, each manager needs to work with their team and their partners/vendors in analyzing the following elements: 1. Site Expectations—It is important to understand how to balance your internal standards with your regulatory requirements, as well as how to keep your neighbors satisfied. 2. Site Aggregate—Variations in native soil, such as clay content or gravel levels, greatly affect the approach that will yield the highest results. 3. Climate—Relative humidity and seasonal variations are critical to achieving predictable results through product choice, application frequency and timing. 4. Daily Traffic—The type and frequency of traffic is an essential variable for site management. 5. Environmental Responsibilities—If you have additional, specifically defined responsibilities, the approach to your site may vary. 6. Budget—While efficiency is the goal of any program, some sites will have more stringent restrictions than others. 7. Current Usage Rates—Document and understand where you’re starting from, both with water, supporting products, and maintenance so that effective measurement of results is possible."

Jan 1, 2018

By David R. Zuchelli, Elio L. . Checca

Two case studies of methane gas explosions and their effect on the operation of underground coal mines are presented. The studies detail the recovery operations and investigations at each mine site. These include the circumstances prior to the explosions and the effects on the surface and underground ventilation control systems. Various ignition sources such as surface and underground electrical power systems, degasification sites, ventilation shafts, test well casings, and lightning activity were investigated. In each case, a lightning report from the National Lightning Detection Network1 was used in conjunction with the physical evidence and eyewitness accounts to confirm lightning strikes as the ignition source for the explosions.

Jan 1, 1995

By Martin L. Smith

Sampling and subsequent geostatistical structural analysis is being carried out on the Bunker Hill Superfund site in northern Idaho's Silver Valley. This paper reports on the findings and methodology used in the initial sampling campaign which had the goal of determining an appropriate sampling grid design, spacing and protocol. Emphasis is placed on those characteristics, of mine wastes which are unique and require special consideration when applying geostatistical analysis. This study represents one of the first applications of geostatistical techniques to the problem of hazardous mining waste site characterization. Remediation of Superfund projects similar to the one described herein represents opportunity as well as liability for the mining industry.

Jan 1, 1992

By James J. Guesk, Robert W. Reisinger, Timothy C. Richmond

A high-altitude (2,900 m [9,500 ft]) historic underground copper mine in Wyoming is discharging copper-laden water with a neutral pH into an otherwise pristine creek. The Wyoming Abandoned Mine Land program is reclaiming the site under a CERCLA deferral agreement. The clean-up goal is to reduce copper in the mine discharge so that the creek can eventually support a trout fishery. A pilot-scale passive treatment test utilizing sulfate-reducing bacteria has been conducted at the site beginning in summer 1997. Test results show significant reduction in copper concentrations in near-freezing mine water at flow rates ranging to 19 liters per minute (5 gpm)

Jan 1, 2000

By Kyle L. Brennan, Scott Maybrier, Gang Chen, Scott Huang

Data from about 3200 drill holes in the offshore area at Nome, Alaska was digitized and processed. Most drill hole files have associated lithology, gold value, and blow count descriptions for each drill hole. The gold intensity was used to present the potential gold resource in the study area on the world wide web. A web page was created that gives background information on the project, descriptions about the Nome area, maps of the claim blocks that include all the normalized slices of gold deposits, and links to other relevant sites on the web. The site is located at http://mineral.uafsme.alaska.edu/nomeproject/nomehome.htm.

Jan 1, 2002

By D. Wright, J. Samborski

DuPont’s Florida Plant has been mining in northeast Florida and supplying titanium-bearing minerals, zircon and staurolite for over 50years.The site has successfully implemented and “sustained” a land reclamation/habitat enhancement program that goes beyond regulatory requirements and standard industry practices. However, the term sustainability has been used by so many organizations, many with divergent viewpoints, that it is important for a mine to develop its over-all concept and approach to sustainable operation. As a foundation, the outstanding reclamation efforts at DuPont’s mine will be presented followed by a broader look at the overall sustainability strategies and tactics used at the site.

Jan 1, 2004

By B. Ballard

Engineers at a West Virginia coal preparation plant owned by one of the nation's largest coal producers sought a fire suppression system for the plant's MCC and cable spreading rooms. Officials considered the traditional options of water-based sprinklers, dry chemical, and clean agent systems; however, each of those options presented challenges. Sprinklers can damage electrical equipment, proper delivery of the agent and adequate coverage/protection can be an issue with dry chemical systems, and clean agent systems require room integrity. An alternative to traditional systems was discovered in the Victaulic Vortex Fire Suppression System. The first hybrid inert gas/water mist system (FM 5580), Vortex adequately addressed these concerns. The system, which deploys a high-velocity, low-pressure mixture of water and nitrogen, is not damaging to electrical equipment and extinguishes fires in open, ventilated areas. This is one of the first installations of the Vortex system in a prep plant, and is a compelling example of how new technology can overcome the challenges of traditional technologies. The paper will detail plant specs, situation, and system evaluation, selection, and configuration.

Feb 23, 2014

By G. I. Mathieu

Research and development studies were carried out at the Canada Centre for Mineral and Energy Technology to produce a synthetic forsterite sand from asbestos tailings for Les Sables Olimag Inc. The National Research Council of Canada also supported and collaborated to the project. Theoretically, the technological approach consists of a heat at over 1300°C; however, the process without additive would result in the production of an enstatite-rich product (MgSiO3) having a fusion temperature less than 1600°C. The purpose was to foster the formation of forsterite (Mg2SiO4), a more refractory compound. The fabrication of the forsterite product requires pre-agglomeration of serpentine-MgO with a binder, which is stable at high temperature, to prevent the loss of the powdered magnesium oxide as dust in the kiln off gases and to maintain the mixture homogeneous during the process. Characterization of the end products with respect to mineral composition and thermal resistance are described. The synthetic forsterite in sand form was tested with success under a bath of liquid steel maintained at 1700°C for up to two hours. The advantages of the new sand and its potential applications will be reviewed.

Jan 1, 1992

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971

By C. D. Harrison, J. W. Parkinson

This paper compares the ash slagging potential of Illinois No. 6 seam coal as raw coal, as commercially cleaned coal processed in a baum-jig plant, and as coal cleaned to a reduced ash specification at the Electric Power Research Institute's (EPRI) Coal Cleaning Test Facility. The comparison is based on ASTM ash fusibility data, a slagging index, gravity fractionation analyses of critical mineral matter compounds, and comparative pilot combustion tests. The first three grounds of comparison are laboratory data. The final comparison involves burning about 13.6 t (15 st) of each coal at Conoco's 4.40-kW/h (1.5 million-Btu per hr) test combustor. The evidence of these four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois No. 6 seam coal.

Jan 1, 1987

By Zhian Liang, Xiong Huang, Weixin Wu, Lifeng Cui, Zhuanhua Wei, Guoyao Li, Xiao Ni, Junrong Wang, Shuiping Zhong

ZJ 201 (modified starch) is a non-toxic, odorless, and biodegradable polymeric depressant, which selectively depressed galena in batch flotation tests while chalcopyrite was not significantly affected. In a plant trial, copper-lead separation was successful for the first time without using dichromate. Moreover, the plant process could be changed to sequential Cu-Pb flotation using ZJ 201 for higher grade lead concentrate. A copper concentrate was obtained with a Cu grade of 24.91% and a Pb grade of 5.11%, which recovered 76.6% of the copper from the original ore; a lead concentrate was also obtained with a Pb grade of 21.90% and a Cu grade of 5.31%, which recovered 52.6% of the lead. In addition to the effective copper-lead separation observed in the plant trial, another improvement observed is that gold was recovered mostly in copper concentrate, which could be sold for higher prices. Au grade reached 230.64 g/t, and its recovery reached 65.8% in the copper concentrate. Au grade in lead concentrate was only 18.90 g/t.

Aug 27, 2021

By Carrie Smith

The Society for Mining, Metallurgy & Exploration’s annual conference and expo, MINEXCHANGE 2026, will take place Feb. 22–25, 2026, at the Salt Palace Convention Center in Salt Lake City, UT. The event will foster a hub for innovation, technical exchange and policy discussion for the global mining industry. Over four days, attendees will take part in short courses, technical sessions, field trips and networking events that highlight the advancement of the mining industry. The conference’s keynote session, titled “Regaining America’s Mineral Dominance,” will start at 8:30 a.m. on Feb. 23 in the Grand Ballroom E–J. The speaker will address the sweeping policy actions now shaping the nation’s mineral future, following a series of executive orders issued by the Trump administration designed to bolster domestic mineral production and energy security. These directives, including Immediate Measures to Increase Domestic Mineral Production (EO 14241) and Establishing the National Energy Dominance Council (EO 14213), have set in motion a coordinated effort across the Departments of Interior, Energy, Defense and Commerce to enhance the United States’ position as a global leader in critical minerals. The invited speakers include Utah Governor Spencer J. Cox and Nate Foster, managing director of Rio Tinto Kennecott, who will examine how policy and industry are converging to meet surging demand for minerals essential to modern technology. Governor Cox is expected to highlight Utah’s long-standing role in American mining, from the early development of Kennecott Copper to its current position as a producer of 40 of the nation’s 50 identified critical minerals. Foster, meanwhile, will offer insights into Rio Tinto’s extensive operations in Utah, including the Kennecott Copper Mine — one of only two operating copper smelters in the United States — and the company’s ongoing efforts to build more resilient, sustainable supply chains. Rio Tinto’s work in critical mineral production, from copper and tellurium in Utah to new operations in Arizona, has made it a fundamental figure in the U.S. mineral economy. Projects such as the Resolution Copper development and the revival of Gunnison Copper using Rio Tinto’s innovative Nuton technology illustrate how private-sector leadership is driving sustainability in domestic mining. These advancements come at a critical moment for the industry, as copper prices remain near historic highs. The keynote session will emphasize that meeting future mineral demand will require a concerted effort between government, industry and technology partners to secure responsible, domestic production. Immediately following the keynote, the Robert E. Murray Innovation Award Lecture will start at 10 a.m. as part of the same session. Lucy England, managing director at FLSmidth, will present on “Sustainable Copper Mining Flowsheets and the MissionZero Mine.” England, who has spent more than 25 years in mineral processing and innovation, will discuss how FLSmidth’s MissionZero initiative aims to develop the world’s most efficient

Feb 1, 2026

By James M. Stauffer

There are many types of filters designed to separate a solid from a liquid, including plate and frame presses, pressure leaf filters, gravity filters and vacuum filters. This discussion will be limited to continuous vacuum filtration and, specifically, to continuous rotary vacuum disc filters, drum filters and horizontal belt filters. The use of vacuum filtration can be advantageous in that: 1. The feed slurry can be delivered to the filter either by gravity or by a simple, inexpensive low pressure pump that only has to overcome the resistance of the feed piping system. 2. The filter equipment does not have to withstand high pressures. Consequently, a wide range of materials of construction, including plastic and fiberglas reinforced polyester (FRP), can be used in the fabrication. 3. After the form time, the filter cake is exposed to the atmosphere and the cake is accessible for further operations such as mechanical or physical dewatering, washing, and sampling on a continuous basis. 4. The discharge of the dewatered solids is continuous for directly feeding to the next operation; for example, a dryer. 5. Various methods of discharge can be fitted to the filter to effect optimum discharge of the dewatered cake solids. The principal of operation of a vacuum filter, regardless of type, is basically the same. The filter incorporates a filter medium supported on a drainage system and arranged so that the mixture to be separated (feed slurry) can be introduced to one side of the filter medium on which the solids are trapped and through which the liquid (filtrate) flows due to the applied vacuum.

Jan 1, 1979

By G. W. Mannard

The large massive sulphide deposits present a formidable challenge to the economic geologist. They represent such huge concentrations of iron, sulphur, base metals and precious metals that it is difficult to conceive how they were derived from the crust or mantle of the Earth. The problem of the origin of massive sulphide deposits has generated a geological controversy which has lasted two hundred years and shows no sign of abating. The economic incentive to solve this problem is great, as the massive sulphide bodies are the moat important source of the world's zinc, lead, and silver, as well as yielding large amounts of copper and gold. Using the criteria of abundance, size, age distribution and gross value of contained metals, the predominant sub-group of the massive sulphide deposits is that which comprises the crudely conformable pyritic (or pyrrhotitic) deposits which occur in stratified volcanic and sedimentary rocks or their metamorphosed equivalents. Examples of this sub-group are: the Buchans, Bathurst, Noranda, Kidd Creek, Flin Plon and Sullivan deposits of Canada; the Mt. Isa and Broken Hill orebodies of Australia; the Cyprus, Rio Tinto, Meggen and Rammelsberg deposits of Europe; Ducktown and the United Verde in United States; and the Kuroko deposits of Japan.

Jan 1, 1973

By W. M. Houston

The phosphate formations of the Pliocene epoch were deposited along the coastal shelf of the eastern seaboard. The deposition of the phosphate is thought to be somewhat contiguous along the early shoreline, and the deposit can be more or less traced over an 800 to 930 mile path from the Florida Gulf Coast, near Ft. Myers, to the Pamlico Sound of North Carolina. This is illustrated in Figure 1. Three areas of commercial importance are currently being exploited from this extensive known deposit: 1 - The so-called ?Bone valley? in Central Florida (multiple operations) 2 - Hamilton County in North Florida (Occidental Corporation operation) 3 - Beaufort County in North Carolina (Texas Gulf Sulphur operation)

Jan 1, 1966