Search Documents

By L. B. Hales

December 3, 1972, James Wm. White presented the results of an instrumentation and process control survey which was sponsored by the Anaconda Company at the annual Tucson Subsection AIME meeting.(1) Twenty-six responses were obtained from questionnaires sent to 48 operating plants throughout the world. The survey results were discouraging in that there were more failures and problems than examples of success. The following quotes are taken from the text of the paper. "We run our mill by the seat of our pants." 'If these blue sky Ph.D.'s (in the instruments and controls area within research) had some operating experience they wouldn't make a lot of the suggestions they do."

Jan 1, 1981

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By Ramazan Comakli, Cemal Balci, Nuh Bilgin, Hanifi Copur, Can Polat, Deniz Tumac

"Application of mechanical excavators for rock excavation in both civil construction and mining engineering fields has increased significantly in recent years. Prediction of the excavation performance of any mechanical excavators – tunnel boring machines, roadheaders, impact hammers, continuous miners and shearers for any geological formation is one of the main concerns in determining the economics of a mechanized mining and/or tunneling operation. A new portable linear rock cutting (PLCM) device was developed in the Mining Engineering Department of Istanbul Technical University and supported by The Scientific and Technological Research Council of Turkey (TUBITAK-112M859). The PLCM is used for cutting small core or block rock samples by a real-life mini disc cutter. The results from the PLCM are compared with the results obtained from the full scale rock cutting tests and theoretical model. It is found that there is reliable correlation between test results obtained from both cutting tests and theoretical model. 1. INTRODUCTION Mechanical excavators are currently the only alternatives to drill and blast due to higher production rate, increased safety, uniform muck size, less roof support, easier ventilation, continuous rather than cyclical operation, and possibilities for automatic control. The most of large civil tunneling and some mining projects are now carried out by mechanical excavators rather than drill and blast methods. Mechanical excavators can be categorized into two main groups: full-face and partial-face machines. Full-face machines such as tunnel boring machines excavate the face in one mode at the size of the cutterhead. Due to their cutting mode, the shape of the face profile by the full-face machines can only be circular. As for partial-face machines, the cutterhead is attached at the end of a boom. The face profile excavated by the partial-face machines can be from circular to horseshoe shape due to the cutting mode of the boom."

Jan 1, 2016

By Jin Dai, Xianwen Geng, Hao Liu, Pu Wang

To investigate how deformation failure occurs in roadways surrounding rock, the relationship between cohesion and plastic shear strain of the strain softening model and the equation for calculating the shear strain of a rock mass in the ultimate elastic state are derived. On this basis, the equality relationship between the built-in maximum shear strain increment and cohesion of FLAC 3D was established to give a more intuitive picture of how the cohesion of the roadway surrounding rock changes. The cohesion attenuation and deformation of the surrounding rock are analysed. The results show that significant deformation in the roadway surrounding rock was caused primarily by the development of large areas of highly softened plastic rock masses towards residual strength. Taking the floor overhead-mining roadway under different rock pillar thicknesses (RPTs) in the Xinglongzhuang Coal Mine as an example, the results demonstrate that investigating the cohesion distribution inside the roadway during mining operation can provide a more intuitive, more accurate description of the degree of failure of the surrounding rock at any point of the roadway, as well as the overall failure range of the surrounding rock. The simulation agrees well with the field monitoring result and seems to be more practically useful than simply analysing the coverage of shear plastic zones. Based on the failure range and degree of roadway surrounding rock with different RPTs, three support schemes are designed. Classified support was implemented for roadways under different RPTs, which realizes the effective control of roadway surrounding rock.

Jan 16, 2022

By Kazumasa Taguchi

At the Kakogawa works of Kobe Steel. Ltd., the agglomeration facilities are composed of a pelletizing plant and sintering plant. This aim is to utilize raw materials efficiently and stabilize the raw material resources. Therefore at Kakogawa works, the blast furnaces (BF) have been operated with high pellet ratio and various developments for pellet properties have been achieved to improve the blast furnace performance. These developments include dolomite-fluxed pellets, new-porous pellets and crushed pellets. As a results of these improvements, pellets have achieved almost the same performance as sinter at high temperature regarding properties such as the softening, melting and reduction behaviour. However, some problems on shape have remained to be solved. Spherical pellets flow easily into the center of the furnace and form mixed layers of pellets and cokes. Therefore, in BF operations with these pellets it becomes more difficult to keep proper and stable gas distribution.

Jan 1, 1983

By J. Franko, M. S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium separation circuits. In this study, the performance of a continuous, laboratory wet-drum magnetic separator was evaluated both with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration and nonmagnetic material. The results indicate that, under certain conditions, the purity of the magnetic material increased after ultrasonic treatment. Key words: Ultrasonics, Wet-drum magnetic separation, Iron ore

Jan 1, 2003

By S. Gundiah

Preparation of functionalized polymers from the polymerization of monomers and preformed polymers are discussed with a few illustrative examples. The methods of their characterization, with reference to their application in flocculation, are described.

Jan 1, 1987

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By Douglas J. Lootens

Geologic mapping was undertaken in the Sierrita Mountains as part of a Doctoral program at the University of Arizona, Tucson. During the study, approximately 35 square miles was mapped in detail, with particular attention given to specific areas of great or significant structural complexity and their relation to mineralization in the vicinity. A combination, of field studies and photogeologic interpretation was used in order to define regional and local structural controls for disseminated copper-molybdenum mineralization in and adjacent to the study area. Gratitude is expressed to the faculty of the University of Arizona, Department of Geology for their assistance in this work and to Bear Creek Mining Company for making numerous reports and drill cores available for study.

Jan 1, 1965

By Claude E. Wykes

Deep Well turbine pumps receive constantly increasing application to the problem of mining water and other fluids from great depths. Many installations of medium settings are presently operating successfully and it is felt that mach greater depths are immediately within reach. Settings and lifts in excess of 2000 feet: are not at all out of reason with present knowledge experience, and materiels; however, conditions of individual applications will govern in each case and dictate methods and possibilities to the designer. Design and operating problems of deep set -turbine pumps ire discussed together with a description of various types of equipment falling within this category. Although the deep well turbine pump has been produced In the vertical turbine pump industry for many years, the connotation of the word "deep" still remains questionable. Among the manufacturers of this type of machinery, answers to the question implying the practical limitation of setting for a deep well pump will vary to an extreme. Most pump designers are in accord that this type of equipment has not yet been exploited to its fullest degree; however, the subject is admittedly fraught with unsolved problems and un¬tried solutions so that such a discussion must necessarily derive from personal opinion and, belief., even though based on substantial experience and background. For this reason, it will be stipulated that the present writing will deal with what may be termed euphemistically ?a highly controversial subject.? During the nineteenth century, a paper was published under proper authority proving beyond question that the human body could not withstand speeds exceeding 20 miles per hour. As a limitation, this looks ' pretty ridiculous to us today. At the beginning of the twentieth century, there was not a single machine in operation that could be described as mullti-stage deep well centrifugal pump. As a matter of fact, very few centrifugal pumps of any type wire operating against heads in excess of 50 feet, since such applications were considered impractical. In the

Jan 1, 1960

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By S. K. Kawatra, T. C. Eisele

Production of highly-cleaned coal for advanced utilization schemes requires close control of the coal ash content at very low levels. For this purpose, a sensitive, low-cost, robust on-stream ash analyzer is needed. The development of such an instrument based on x-ray backscatter and fluorescence is described, including features to improve its sensitivity at low ash levels. The performance of the resulting device in testing a real coal sample is discussed.

Jan 1, 1990

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By Minor S. Jameson

This paper presents considerations in support of a U. S. oil import policy more restrictive than the present Government import program. A lower level of imports and greater long-range stability in the relationship between imports and domestic production are recommended. Reference is made to increasing world-wide surpluses of oil and wide disparities in foreign vs. domestic costs. Resulting economic forces are held responsible for the increase in imports (excluding residual fuel oil) of almost 300 percent and the change in ratio to domestic crude production from 5.4 percent to 13.9 percent during the period 1946-1956 prior to import restrictions. It is pointed out that these imports continued to increase during the years of import restrictions to a ratio of 17.3 percent of domestic production in 1961. Data are presented showing that increasing oil markets outside the United States provide an outlet' for more than 80 percent of total foreign production, with 90 percent of the increase in foreign production going to foreign markets. Attention is called to the fact that, if there had been no increase in United States oil imports during the past five years, foreign production would have increased by 45 percent in contrast to a static level of domestic crude oil production. The need for a less restrictive import policy in the interest of encouraging foreign oil development, therefore, is questioned. Declines since 1956 in the range of 30 percent in domestic exploratory crews, rotary rig activity and wildcat well completions in the United States are cited, together with a decrease of 9 percent in industry employment and increases of 9 to 18 percent in elements of cost. Recognizing that factors other than imports affect the domestic industry, it is concluded that continuing declines in the vigor, capabilities and competitive structure of the domestic industry can be expected unless further import restrictions are imposed. The public interest in assuring adequate domestic supplies is considered in the light of the role of oil and gas as a source of almost three-fourths of U. S. energy requirements and the economic benefits from petroleum production with a value exceeding the combined value of all other minerals in the United States.

Jan 1, 1962

By D. C. McDonald, P. R. Whincup, H. Duke

Due to grade, overburden depth and stability and the presence of groundwater it was considered impractical to recover gold contained in unconsolidated palaeochannel sediments by conventional mining, dredging or borehole mining techniques. A series of field experiments was conducted to determine the feasibility of recovery of gold by in situ leaching from sediments located at a depth of about 80 metres. The test wellfield site and plant are described together with field test procedures, results and wellfield rehabilitation procedures. Choice of sodium cyanide as leachant and laboratory testing are discussed in relation to groundwater and sediment chemistry and problems encountered in field tests.

Jan 1, 1989