Search Documents

By B. Tolwinski

Long-Term Open Pit Scheduler or L-TOPS is a new software package for evaluating, planning, and design of open pit mines. L-TOPS transforms geological, economic, and technical information about a mineral deposit into a detailed mining schedule that maximizes economic efficiency without neglecting the practical requirements of mining operations. L-TOPS has been customized for integration with Placer Dome Inc.'s existing in-house resource/reserve optimization software to function as a primary tool for property acquisition studies and for the designing of mines for feasibility studies. This pa-per presents an overview of L-TOPS and reports on its application to Placer Pacific's (Placer Dome's Australian affiliate) Mt. Rawdon project.

Jan 1, 1996

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By VASU GANGRADE, Marcia Harris, Kumar Vaibhav Raj, Jim Addis, Khaled Mohamed, Snigdha Sarkar

The National Institute for Occupational Safety and Health (NIOSH) conducted a ventilation assessment for a recently established underground room-and-pillar stone mine implementing split-mine ventilation. The primary objective was to examine the impact of the length of the in-place stone stoppings on face ventilation efficiency. These stone stoppings serve to separate the intake and exhaust entries and align with the mining direction. To achieve this, computational fluid dynamics (CFD) modeling was utilized. The appropriate turbulence model was selected, and a mesh convergence analysis was conducted for the CFD model. Following that, the CFD model was validated using the conducted ventilation surveys. Two configurations of in-place stone stoppings, designated as Layout-I and Layout-II, were simulated using the validated CFD models. Layout-I featured a shorter in-place stone stopping, while Layout-II had a longer one. The results obtained from the CFD models demonstrated that the increased length of the in-place stone stopping in Layout-II resulted in a notable enhancement in ventilation efficiency at the advanced faces (last stopping), elevating it from 4% in Layout-I to 8.4% in Layout-II. However, no significant impact of the in-place stopping layouts was observed at other faces. In general, Layout-II exhibited a greater circulation of air at the outby stoppings.

Feb 1, 2024

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By K. T. Brashear, N. Ripepi

"Over recent years, specifically following the MINER Act of 2006, an increasing number of manufacturers of underground mine seals in the United States have begun using a form of pumpable cement or shotcrete to create barriers separating the working and abandoned sections of underground coal mines. This seal material, while generally considered to be homogenous and solid, contains a network of microcracks, voids, and delaminations. Generally, it has been assumed that methane (CF4) leakage around these seals is a result of movement around the boundary interface between the seal and surrounding strata. Using a perfluorinated tracer compound, perfluoromethyl-cyclohexane (PMCH), the movement of gases can be monitored through seal material to observe how gases move though the material, both intact and with faulting in the material. This paper documents two large experiments where the movement of PMCH was monitored in the field, along with modeling confirmation using 3D visualization software. INTRODUCTION According to a report in 2007, there were over 14,000 active mine seals in underground U.S. coal mines alone (Zipf, Sapko, & Brune, 2007). These seals are used for both ventilation and safety purposes, to direct the flow of air away from the abandoned area of the mine and to help eliminate the propagation of explosions that can occur on the outby side of the mine seal. The atmosphere on the outby side of these seals typical consists of low levels of methane that have the potential of producing leakage along the face of the seal on the inby side. Methane leakage around mine seals has historically been attributed to the permeability between the seal and mine interface (McPherson, 1993). According to the United States Bureau of Labor Statistics (BLS) between 2003 and 2012 an average of 17 deaths occurred annually in underground bituminous coals mines. The only time during the ten-year period where the fatalities were higher than the average was in 2006 and 2010, years which had three major explosions occurring in underground coal mines in West Virginia and Kentucky. Two of the explosions were propagated through the mine by seal failure or methane leakage around newly poured seals (Light, et al., 2007) (Gates, et al., 2006). These recent events, and new regulations regarding seal strength (MINER Act), have created a need to monitor the condition of underground mine seals. BACKGROUND Measuring the permeability of solid materials, such as concrete or seal materials, can be a valuable tool in the field of non-destructible testing (NDT). By using an inert gas, such as nitrogen, injecting the gas into a solid structure, and measuring the resultant flow rate and pressure differential, this can provide valuable information about the structure. Studies have shown permeability can be affected by the stresses applied to the structure, as well as temperature and moisture (Choinska, Khelidj, Chatzigeorgious, & Pijaudier-Cabot, 2007) (Abbas, Carcasses, & Olliver, 1999)."

Jan 1, 2015

By James E. Lonergan

To determine the best materials handling system for surface mined materials, one must develop a mine plan for each candidate system based on the most efficient use of that system. This is essential for a fair, unbiased economic compari¬son of the candidate systems. This paper will present two case studies where an integrated mine planning /systems engineering approach has been utilized at different levels of detail in the analysis of an in-pit crushing/conveying system vs. total truck haulage at 2 open-pit copper mines.

Jan 1, 1985

By B. C. Scott

Every year more and more mining companies are entering joint ventures to look for minerals. Large companies join large companies, small companies join small companies, and large companies join small companies. Mining companies join oil companies, chemical companies, machinery companies, and companies with no other connection to the minerals business. And well they might, for here is a way for both minerals-oriented companies and those that have no background or knowledge of the minerals business to get actively involved in an outwardly-attractive but high-risk enterprise with the chance to participate in a lucrative minerals find. Thus, for reasons beyond those normally associated with joint ventures in many other fields, corporations, companies, groups, and even individuals are looking to joint exploration ventures as the answer to all problems of getting into or staying in mining.

Jan 1, 1972

By P. Karimi, A. Akcil, A. Amini, H. Abdollahi

"In this study, cyanidation experiments were carried out on a massive sulfide ore sample, whose grades of the precious metals gold and silver were found to be 4.2 g/t and 311.9 g/t, respectively. Other elements in the ore were arsenic with average grade of 1,751.6 g/t; antimony, 619.7 g/t; zinc, 781.4 g/t; copper, 454.6 g/t; lead, 101.8 g/t; mercury, 324.3 g/t; and bismuth, 0.6 g/t. The first objective of test work focused on determining the best conditions for extracting gold from the ore, ground to less than 75 microns. Different influential parameters such as particle size fraction, cyanide concentration, pH and leaching time were investigated. The optimum parameters were found to be particle size fraction of less than 25 microns, cyanide concentration of 2,000 mg/L, pH of 11 and cyanidation time of 24 hours. In these optimum conditions, the highest gold and silver leaching efficiencies were 76.88 and 59.63 percent, respectively. In addition, roasting as pretreatment at a temperature of 700°C over a period of two hours was evaluated. Cyanidation testing of the roasted ore in the optimum conditions found increases in the gold and silver leaching efficiencies to 85.97 and 67.57 percent, respectively. Moreover, antimony extraction rose to 43.10 percent, from 23.73 percent without roasting.IntroductionGenerally, gold ores can be classified as “free milling” or “refractory,” depending on how they respond to cyanide leaching (La Brooy et al., 1994; Celep et al., 2009). While high gold recoveries (> 90 percent) from free-milling gold ores can be readily achieved, refractory gold ores are often characterized by low gold recoveries (50-80 percent) within a conventional cyanide leaching process (Rubisov et al., 1996; Adams, 2005; Celep et al., 2009). The presence of preg-robber components such as carbonaceous matter, sulfide minerals and aluminosilicate can further decrease gold and silver dissolution rates and recoveries. With the negative effect of the presence of preg-robbers, gold dissolution is considerably diminished in solutions with high cyanide concentration (Tan et al., 2005). In such refractory gold ores, gold particles may sometimes be occluded or included in the sulfide minerals, and pretreatment becomes necessary to break down the mineral structure to liberate gold for subsequent recovery. These ores are usually pretreated with an oxidizing process, after which gold and silver can be recovered by a standard cyanidation process. The main oxidizing processes available for refractory gold ores are roasting (LaBrooy et al., 1994; Angelidis and Kydros, 1995; Li et al., 2009; Karimi et al., 2010; Kyle et al., 2012), biological oxidation (Lawrence and Bruynesteyn, 1983; Komnitsas and Pooley, 1990, 1991; Deng and Liao, 2002; Ciftci and Akcil, 2010, 2013) and pressure oxidation (Mason, 1990; Murthy et al., 1992; Qingcui et al., 2009). In addition, ultra-fine grinding is being used in some plants for the liberation of gold and silver particles that are interlocked in the sulfide or silicate minerals (Celep et al., 2011)"

Jan 1, 2015

By Norman D. Harte, George W. Holl

The development of the most important tool used in Site Testing is reviewed briefly and the application of the information gained is described. The operation of Site Testing and pregrouting of underground excavations is dealt with in detail. Practical experiences (and pitfalls into which the inexperienced might fall) are recorded. But for the application of Site Testing and grouting of shafts, tunnels and other excavations, vast areas of the present goldfields in South Africa would remain unexploitable.

Jan 1, 1981

By Anthony W. Wakefield

The paper is intended merely as an introduction to methane hydrates, what they are and why they are important. It does not claim to be a cutting-edge research report, but may be useful for those to whom the subject is unfamiliar.

Jan 1, 2008

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010

By A.M. Wala

A new radioactive tracer method to measure airflow in inaccessible airways has been developed for situations when studies of the mine ventilation system are not possible using conventional flowmeters (anemometers). The new method has been tested in the ventilation laboratory at the University of Kentucky and in the Experimental Underground Coal Mine at the U.S. Bureau of Mines. This new tracer method has been utilized in leakage, dilution and flow velocity measurements in laboratory and field (mine) experiments.

Jan 1, 1996

By Mark J. Dowiak, Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980s. About 45 Mt of hazardous wastes are produced yearly. One major aspect of the problem is the siting, design, and construction of' environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sites for several reasons. • Surface mines offer an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic, savings when compared with sites on undisturbed lands that might require extensive excavation or embankment construction. • Surface mines often have an abundance of mine spoil available that could potentially serve as construction material. This could result in a significant economic advantage over other sites that might require extensive amounts of construction material to be excavated or hauled in. • Operation of a commercial disposal facility in a surface mine can reduce or totally alleviate reclamation costs. • For an abandoned surface mine, conversion into a disposal facility could represent a positive form of land use and may provide a means for reclaiming lands that would otherwise remain unreclaimed. Despite these positive reasons, there are many technical factors associated with surface raining that can make the prospect of disposal site development an uncertain one. Before discussing factors associated with mining that can present siting, design, or construction problems, some understanding of the basic components of a chemical waste disposal facility is necessary.

Jan 2, 1981

By Kostas Fytas

Canada still remains today a strong resource nation with a huge geological potential. Canada ranks among the top five leading countries in the production of 15 major minerals. Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage production. It is estimated that across Canada there are a few thousand abandoned mine sites as a result of the last fifty years of mining. Most of these sites are acid producing presenting a serious threat to the environment. It has been estimated that the cost of stabilizing and reclaiming these sites across Canada will be over $5 billion over the next twenty years. Current practices for decommissioning acid producing sites are water covers (flooding), dry covers, revegetation and treatment of the acid effluents. This paper presents the technical and legal issues of mine closure and reclamation in Canada. The methods used in the revegetation of acid producing mine sites is also presented This paper also reviews the financial guarantee requirements for mine closure by the provincial legislations in Canada. A case study of stabilizing and reclaiming a sulphide tailings area in the Sudbury region is presented. It illustrates the challenges facing the Canadian Government and the mining companies in restoring and revegetating the closed and abandoned mine sites across Canada.

Jan 1, 2002

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By Robert R. Unterberger

The purpose of this paper is to summarize the research of the past sixteen years on three distinct methods of probing into solid rock. The first method is to use radar of the appropriate frequency. The second method is to use sonar. The third method is of recent vintage and uses techniques of nonlinear sonar also known as parametric sonar. The first two concepts, that of radar and sonar, are common to most people. Very few have heard of nonlinear sonar. Each of the probing techniques were investigated in order to overcome deficiencies in the former technique. Each has its advantages and disadvantages. It should be emphasized that all of these techniques for probing (or seeing) into rock are used in mines, and generally speaking not from the surface. Only in very special cases, such as certain very dry parts of Egypt or Peru, or, for example, the surface of the moon, will these probing techniques work from the surface. The reason for the development of these probing techniques has been to alert miners to possible hazards ahead of mining. Such hazards may be (1) old (unknown) boreholes connected with high pressure water zones above, (2) fractures that might connect to the Gulf of Mexico above the mine, (3) water-filled fractures that threaten the safety of miners, or (4) the discovery of dry faults ahead that can disrupt the planning of future operations.

Jan 1, 1983

By R. L. Amelunxen

P. T. Freeport Indonesia (PI) in conjunction with Crescent Technology Inc. has developed a method to predict the metallurgical performance of ores blends based on the behavior of their component ores. The question addressed in this paper is whether ores treated individually could be extrapolated to predict the behavior of a blend of ores. The work further investigates the use of modal analysis to establish individual mineral flotation kinetics in each of the ore zones. This information would lead to the prediction of grade-recovery curves of ores made up of those minerals. Nine samples of ore, representing various zones of FI's Grasberg ore deposit were tested metallurgically and examined microscopically. The same testwork was performed on blends depicting the 1994 mill quarterly feed. Flotation kinetics of the individual ores were then "mathematically" blended and compared to the results obtained from the quarterlies. The calculated kinetics of the actual blends of ore received by the mill were fed to the simulation program and compared to the actual mill performance.

Jan 1, 1995

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM's Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By S. G. McDowell

This paper discusses the utilization of automation to increase productivity of continuous miners. Automation techniques are used during the design stage to decrease the time required and ensure the accuracy of the design. This is followed by automated manufacturing processes to reduce manufacturing time and improve the quality and consistency of parts. Combined, the result is a more reliable machine which can provide ongoing production capability. With the use of automation to enhance operator effectiveness and monitoring machine condition the productivity of machines is also improved.

Jan 1, 1991