Search Documents

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

By S. Castro, L. Gutierrez

A classification of flotation processes carried out in concentrated electrolyte solutions, e.g., seawater, is proposed using the most obvious features of these processes: low or high content of Mg2+ and Ca2+ ions, pulp ionic strength, and pH. The first distinguishable group is the processes carried out in NaCl/KCl solutions, about 0.5 M in the case of salt flotation of inherently hydrophobic minerals, and at concentrations about 10 times higher in the flotation of potash ores. In the flotation of sulfide ores, such as nickel or copper ores, with xanthate-like collectors, the xanthate collector is apparently not affected by pulp ionic strength and only adjustment of frother may be required. Content of Mg2+ and Ca2+ ions in seawater is the main difference between such systems and fresh water. The presence of these metallic ions can adversely affect flotation in the pH ranges over which these ions hydrolyse. The successful flotation of Cu-Mo ores typically requires depression of pyrite at high pH values achieved with the use of lime. However, in seawater, flotation of Cu-Mo ores requires removal of the hydrolysis products of the Mg2+ and Ca2+ ions or the use of a pyrite depressant that can be effective over the pH ranges that are much below the pH of hydrolysis. Mg2+ and Ca2+ ions also affect flotation of phosphate ores with fatty acids. In this case, the depression mechanism is not caused by precipitating magnesium hydroxides on the mineral surface but by precipitation of collector insoluble salts, and the same ions are responsible for depression in both cases. In the seawater flotation of Cu-Mo sulfide ores and phosphate ores, the practical solution involves either removal of Mg2+ and Ca2+ ions prior to the flotation or complexation with other reagents.

By J. J. Wallaert

The decreasing supplies of natural gas and low-sulfur crude oil available for electric power generation in the United States will unquestionably shift the emphasis to nuclear and coal fired steam power plants in the immediate future. Failure to do so will ensure our dependence on mid-east low sulfur crude oil comprising some 70% of the known world reserves, and imported liquid natural gas. By contrast, the United States has 43% of the known world reserves of anthracite, bituminous and semi-bituminous coal and 48% of all known coal reserves of the world including lignite. It is evident, therefore, that coal is alive and well and will continue to be a significant energy source for the production of electricity for many years. Of course, concern for our environment and the development of new technologies will ultimately curtail the utilization of coal for the generation of bulk power, but information released by the National Electric Reliability Council and the Federal Power Commission is worth repeating. In the year 1972 the total capacity of generating units in the United States was 379,552 Mw of which 149,974 Mw, or 39.5% of the total, was produced by coal fired steam turbines which consumed 344,700,000 tons of coal. New capacity additions planned or in construction show that in the year 1981 our total generating capacity will be 843,503 Mw, of which 257,995 Mw, or 30.6% of the total, if from coal only. Translating this increase into terms meaningful to the bulk material handling industry suggests that ten years from now the utility industry will require 590,000,000 tons of coal per year - a monumental task - if we are to sustain our current demand rate for power.

Jan 1, 1973

By R. Reeves

Coal producers and utilities depend on automated coal blending systems to reduce costs and meet stringent environmental regulations. Over 30 systems installed in the United States since 1987 use on-line PGNAA (Prompt Gamma Neutron Activation Analysis) analyzers to accurately control the blending process. Experience and detailed engineering are required to integrate real-time data produced by the coal analyzer with a control system to meet demanding performance specifications. This article reviews successful installations and lists important features including interfacing analyzers with plant control systems, specifying feeders and weigh scales, and managing data.

Jan 1, 1995

By Mark Laffoon

Gold Fields Operating Co.-Chimney Creek has conducted numerous ore reserve modeling studies In order to optimize the estimates of the gold grades and tonnage distributions. Improved models continue to be produced for the major pits which Increase confidence levels required by Gold Fields management and provide the basis for more accurate long and intermediate term mine planning. Various kriging and non-kriging estimation techniques are used at Gold Fields -Chimney Creek Mine. This paper reviews the modeling histories and, current procedures used to construct these models with particular emphasis on the North Pit deposit.

Jan 1, 1991

By J. D. Isbister

Coal is the most abundant and most economical source of energy in the United States, however, combustion of coal results in release of pollutants to the environment. The release of sulfur dioxide and oxides of nitrogen during combustion of coal contributes to the deterioration of the environment. Energy independence in the United States must include the increased use of coal reserves. Increased reliance on coal for energy will dictate the necessity for making coal a cleaner fuel. New technologies employing a variety of techniques from harsh chemical treatment to mild physical separations to clean coal are rapidly becoming available. Success for any coal cleaning process is in economics which translate into efficient removal of sulfur with high recovery of combustibles as well as low capital and operating costs for the process. Conventional coal cleaning processes remove water soluble sulfates and a portion of the pyritic sulfur and ash from coals. Removal of additional sulfur from coals requires more advanced coal cleaning techniques. Coal contains many organic sulfur forms which are the most difficult of the sulfur types to remove from coal. The heteroaromatic sulfur species, such as the comlex thiophenes, are the most commonly found organic sulfur forms. These sulfur forms are resistant to chemical attack and are considered to be refractory compounds. Atlantic Research Corporation has developed an "unique" microorganism, CB1 (Coal Bug 1), capable of oxidizing thiophenic sulfur in coal to form water soluble sulfates.

Jan 1, 1986

By Kazmierczak J. B., Klein E., Kinscher J., Lizeur A., De Santis F.

In this work, we propose to implement machine learning methods for the automatic classification of mining-related seismic data. The approach retained for the classification is based on a Convolutional Neural Network (CNN) which has been tested and applied to two different mining datasets: the active ore mine of Garpenberg (Sweden), currently under exploitation, and the abandoned coal mine of Gardanne (France), where mining stopped in 2003. The first step of the approach consists in creating a well classified (manually) database of seismic signals separated in different classes as a function of the seismic sources. The selected database is then divided into two groups: train, containing the 70% of the signals, and test, which contains the remaining 30% of the signals within the selected database. The learning phase of the algorithm consists in creating a classification model based on the train group, which is further validated on the test group. The application of CNN for the automatic classification of Garpenberg and Gardanne seismic data shows, respectively, that about 88% and 98% of the seismic events of the two sites can be properly classified. These results demonstrate that machine learning could be a powerful tool for microseismic monitoring in mining and post-mining environments, which could be further extended to the whole automatic processing of seismic data, including signal’s classification as well as microseismic event’s localization.

Apr 26, 2022

By Steve Karl

"The International Tunnelling and Underground Space Association (ITA) held its 42nd General Assembly along with the 2016 World Tunnel Congress (WTC) April 22-28 in San Francisco, CA. The event was co-organized by the Underground Construction Association of SME (UCA). This was the first time the event has been held in the United States in 20 years.As cities demonstrate strong needs in tunnels and underground spaces for public transportation, subway stations, hydroelectric infrastructures and other underground infrastructure needs, the WTC 2016 provided the 2,319 attendees from around the world a unique occasion to discover the latest state-of-the art innovations in urban planning and underground construction projects in the United States and worldwide.The Congress, held in lieu of the UCA’s North American Tunneling Conference, included an exhibit that attracted 226 exhibitors in 298 booths. The exhibit had on display the latest in technical equipment and services from some of the largest and best companies in the international tunneling industry. The exhibit hall was also the place where participants were able to interact with the authors of the 168 posters and receive answers to various topics directly concerning civil engineers: innovative procurement processes, cost and risk management, contractual methods, BIM technologies and examples of innovative underground infrastructures built worldwide. And the technical program included 353 technical presentations – 185 podium and 168 posters.What is ITA?ITA-AITES is a nonprofit, nongovernmental organization that promotes greater use of underground space as a key instrument in sustainable development. Established in 1974 and based in Lausanne, Switzerland, ITA-AITES is made up thousands of professionals involved in the tunnel and underground space industry, including engineers, project owners, town planners, architects, industrial designers, companies specialized in public works and major structures, suppliers of construction site facilities and equipment, lawyers, politicians, researchers and academics, economists, financial experts and other stakeholders.ITA-AITES consists of 73 member nations and 300 affiliated members, including 15 major sponsors and 60 donors. The association is run by an executive council made up of 15 members elected by the 73 member nations, each representing a different dimension of the tunnel community."

Jun 1, 2016

Silver bearing bulk sulfide concentrates from several Peruvian mines were autoclaved in a 19 liter (five gallon) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates following a hot lime jarosite destruction step extracted over 98 percent of the silver and over 95 percent of the gold. Autoclave operating parameters such as time, temperature, pulp density and autoclaved solids recycle were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving, and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to pro-vide reliable scale up data for a 50 -100 ton per day facility.

Jan 1, 1992

By Patrick Linzer, Lindsay Linzer

By its nature, seismology has been a data intensive field since the first digital computers were introduced in the 1950s. The first empirical models were developed in the same period and are still widely used today, for instance, the Gutenberg-Richter frequency-magnitude relationship (Gutenberg and Richter, 1956). Machine learning (ML) methods make it possible to redefine these empirical models using large datasets and examining considerably more parameters, where their significance to the problem being addressed is methodically and repeatably evaluated using robust statistical methods. In this paper we develop a simple logistic model for the short-term prediction of seismic events above a threshold magnitude from a mine’s event catalogue comprising more than a million events with 14 basic parameters from which a pool of over 830 derived parameters was developed, covering a series of 11 precursory time windows. The logistic model was fitted stepwise using SAS with α = 0.025 for both entry and acceptance. 25 variables from the pool met the acceptance criterion. The findings were surprising in that parameters a rock engineer or seismologist might have expected to be the most significant in the logistic model were not; instead, it was an increase in standard deviation of the immediately-prior seismic magnitudes that carried the most weight, followed by the average maximum source displacement and median apparent volume change. These findings make intuitive sense because the increasing scatter of the magnitude shows an increasing number of large events being recorded that could be indicative of instability in the system that could lead to large events. The model is rudimentary and enormous scope exists for more exploration in terms of data pre-processing, model types, and response variable definitions.

Apr 26, 2022

By Jon Y. Kaneshiro, Eric Dawson, Pooyan Asadollahi, Steven Hunt

This paper provides updates to the paper published by the lead author at RETC 2011 with a summary of developments in technologies, products, and approaches to corrosion analyses of gravity sewer tunnels and microtunnels. This paper presents approaches in evaluating degradation of reinforced concrete liners. Also, the carbon footprint of conventional concrete liners and alternative “green” liners are compared and their life cycle costs are considered. A few case histories from the past decade are provided indicating the latest and emerging trends in liner protection.

Jun 13, 2023

By F. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower Partnership Mine to Twin Buttes. The system, supplied and installed by Cable Belt Limited, of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240 kw (3000 hp) drive and a 60° angle bend. Construction was completed in two years. Full production was attained after several months' operation.

Jan 1, 1979

By C. G. Clifton

The Oatman District produced approximately 2.2 x 10 6 ounces of gold and 0.8 x 10 ounces of silver between 1897 and 1942. A total of 3.8 x 10 tons of ore averaging 0.58 O/T gold and 0.17 O/T silver was extracted from eight major orebodies and a number of lesser deposits. Oatman lies at the center of a trachyte-latite-rhyolite volcanic complex which contains at least one resurgent caldera. The orebodies are typical epithermal quartz-calcite + adularia lode deposits which are very deficient in sulfur. Ore deposition has occurred within dilatant zones on faults which radiate from a common point within-the complex. Fischer-Watt Mining approached the Oatman District with an integrated exploration program utilizing four basic procedures to define the characteristics of past productive areas the results of which were applied to unexplored portions of the vein system. These procedures, listed in their order of usefulness, in defining known and prospective mineralized zones are: vein contouring, detailed alteration mapping, fluid inclusion temperature determinations, and geochemical sampling.

Jan 1, 1980

By A. P. Grobbelaar

Andalusite is a member of the sillimanite group of minerals consisting of andalusite, kyanite, and sillimanite. These minerals are the structural polymorphs of Al,Si05 (the anhydrous silicate of aluminium) and although chemically similar, they differ in physical properties due to their different crystal structures. For further information on the sillimanite group, see the chapter on Kyanite and Related Minerals that follows. The minerals are generally the products of the metamorphism of alumina-rich sediments and are found in schists, gneisses, or hornfelses, which have undergone either regional or thermal metamorphism from their original form. Sedimentary deposits may also form since the minerals are chemically and physically resistant to breakdown. When heated to a sufficiently high temperature the sillimanite group minerals convert to mullite with a resultant volume expansion and the liberation of silica. Due to the stability of the mullite formed, its high hot strength and resistance to chemical and physical erosion, they are widely used in the manufacture of refractories and special ceramics (Table 1). The reaction can be represented as follows: [ ] The worldwide use of these minerals depends to a large degree on their availability (Fig. 1). Andalusite, with its lower conversion temperature and the lowest volume expansion on being heated is the natural choice as a raw material to produce energy-saving refractories without prior calcination. The Republic of South Africa holds by far the largest minable andalusite deposits of the world, estimated at some 70 Mt of known in situ reserves. The only other large commercial production of andalusite comes from France, with known reserves of about 5 Mt. Potential new deposits are known from China, Ireland, Australia, and South America. World consumption of andalusite in special performance refractories has risen from less than 10 ktpy in 1960 to nearly 300 ktpy in 1990, which is due to cost effectiveness in many industrial applications compared to other conventional refractory products. Andalusite-based refractories have traditionally been used in Europe, South Africa, and the Far East; usage in America was limited in the past due to relatively high delivery costs and availability of other local refractory minerals. However, there is a significant trend towards greater use of andalusite in North America, thus opening new markets and replacing other traditional refractory raw materials. GEOLOGY Andalusite occurs in metamorphosed rocks of clay-like com- position, as in the andalusite-hornfelses in thermal aureoles (contact metamorphism), formed under conditions of high temperatures and low stress, and in regional metamorphic rocks, such as the andalusite-schists. These schists are mostly unconnected with definite igneous intrusions but were presumably also formed at high temperatures and under low stress. Andalusite can also appear in alluvial deposits associated with the primary deposits. At depths of 10 to 20 km, temperatures of up to 450°C might be expected. Another result of increasing depth is an increase of pressure due to the load of the rock cover. The load stresses involved in metamorphism is generally believed to lie in the range 0 to 10 000 bars. During contact metamorphism the increase in temperature is brought about by the injection of magma. The temperature reached in the country rock at some distance from the igneous body will always be less than the initial temperature of the intrusion, which is presumably less than 1 200°C, and will vary with time and distance from the contact. A simple metamorphic reaction involving dehydration of an aluminous sediment can be: [ ] At higher temperatures sillimanite would form at the expense of andalusite, while kyanite would be the mineral formed at higher pressures, as can be seen in the phase diagram of A12Si05 (Fig. 2).

Jan 1, 1994

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector is one of the leading sectors where work accidents are most intense because of the constant change of work environment and heavy working conditions. The losses and the halt of production after the accident negatively affect productivity and production efficiency. It has been found that there are very few studies on the use of Data Envelopment Analysis (DEA), which is one of the nonparametric efficiency analysis methods, in the evaluation of mining sector occupational accidents. According to parametric activity measurement methods, it has been tried to show that the DEA can also offer the opportunity to interpret work accidents by taking advantage of its advantages. Due to the application of open-pit mining methods along with underground working techniques which increase the risk factors with respect to accidents at work that occurred between 2012 and 2018 of Western Lignite Corporation (WLC) were tried to be analyzed in the present work. As a result of the analytical work using Data Envelopment Analysis (DEA) for the years 2014, 2015, 2016, 2017, and 2018, inefficiency has been determined in both underground and surface operations. According to the results obtained, it was determined that WLC could not produce enough production in both the underground and surface coal mining operation, despite the accidents that occurred, while it had the opportunity to produce more. In addition, it was found that the increase in accidents occurred more than the increase in the amount of production during the years studied.

Jul 4, 2021

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By Michelle Mangione, John Kuyt, Zili Li, Michael Mooney

"Twin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world.A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a better understanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This article discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link project overview. The Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with more than 7 km (4 miles) of twin-bore road tunnels, two lanes each, with several caverns, interchanges and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a public-private partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5-m (41-ft) double-shield Herrenknecht tunnel boring machines (TBM) (Harding & Francis, 2013). The TBMs were used in earth pressure balance- (EPB) type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1-m (39.8-ft) diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in nine segments + one key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis (Harding & Francis, 2013). Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Mar 1, 2017

By E. J. Mayhew

Bentonite and newly discovered deposits of sepiolite, saponite, and hectorite are now being processed and marketed from the Amargosa Valley of Nevada. All of these deposits are large. The bentonite has been known for decades and is the whitest known. The only other sepiolite deposit is in Spain. The only other commercial hectorite deposit is at Hector, California. No other saponite deposit is known. All the components except bentonite are hydrous magnesium silicates. The bentonite is mixed layer Na-Ca. All the materials have characteristics unique to their locale and type, such as high yield point for drilling muds and liquid suspending agents. The sepiolite has geothermal stability. Figure 1.

Jan 1, 1979

By Ashish Ranjan Kumar, Barbara Arnold, Luis Sanchez Gonzalez

Mining operations adopt a variety of measures to combat dust underground. These include ventilation systems, water sprays, physical barriers, and personal protective equipment (PPE). Respirators are a class of PPE that can provide clean particulate- free air to the users. Powered Air-Purifying Respirators (PAPRs), used commonly in medical and other sectors, are not prevalent in the mining industry. PAPRs use P100 filters that have 99.97% dust capture efficiency. We present our results from computational fluid dynamics (CFD) simulations performed to understand the impact of a PAPR on airflow and dust particle concentration in the vicinity of a miner. These results show that donning PAPRs can lower the miners’ exposure to respirable coal dust in their workplace.

Feb 1, 2025

By J. Loredo

Wastes related to abandoned mine sites can constitute important potential pollution sources, depending on their mineralogical and geochemical characteristics and volume. Mine waste disposal sites contain a diverse variety of wastes including overburden material and waste rocks, the ore which cannot be economically removed and wastes from the smelting processes when they are accomplished at the mine site. These materials are usually heterogeneous in size, mineralogy and metal concentrations. Asturias, in northern Spain, has an extensive mining history and, in consequence, there are abundant unreclaimed and derelict mine sites with abandoned mines and spoil heaps of different age, morphology, content and dimensions. In these spoil heaps, waste materials are subjected to the intense action of a humid environment, so the instability of sulphides and sulpharsenides results in the production of acid and metal-rich leachates, which are incorporated to surface water or infiltrated through the land reaching groundwater bodies. The mineralogical and geochemical characteristics of the stored materials are key data to evaluate if they represent an environmental risk. Mineralogy and geochemistry of wastes and the particular specific environmental conditions of each site affect the rate of weathering and therefore the metal release. The characterisation of mine wastes is a necessary step in order to establish suitable assessment strategies with the aim of reducing the leaching, transport and widespread of ecotoxic elements from mining wastes to the environment (surface water, sediments, soils and air). As a consequence of the weathering of As-rich mineral phases, high arsenic contents are commonly detected in effluents from mine voids and spoil heap leachates.

Jan 1, 2006