Search Documents

By T. Harrison

Surface coal mines in West Virginia are receiving stringent NPDES discharge limits for total recoverable selenium. With limits in the low parts-per-billion range, selection and implementation of proper sample collection and analytical methods are imperative for quality assurance and control and for consistency in results. Given the typical oxidized form of selenium in the water, the low limits and the large and variable flow rates from the watersheds, end-of-pipe treatment is difficult and cost-prohibitive to implement. Discharge locations in the remote and steep terrain exacerbate the problem. To evaluate options for end-of-pipe treatment at a Patriot Coal Corporation surface mining operation in West Virginia, CH2M HILL performed wastewater characterization for a range of key constituents and selenium species at three outfalls for selection and preliminary sizing of appropriate treatment processes. A preliminary evaluation of base and wet-weather flows was done to understand flow variability considerations for discharges. A conceptual evaluation of technologies to treat selenium to permitted levels was conducted in con-junction with order-of-magnitude life-cycle cost estimates.

Jan 1, 2010

By Sara Swiokla Korsikas, Toren Olson, Amado Guzman, Yuri O. Zepeda P

Ore agglomeration has been used as part of the heap leaching process for the last 40 years. However, industrial experience shows that the lack of a universal agglomeration standard has limited the benefits of this, otherwise, valuable unit process. The more complex the ore, in terms of the nature and relative abundance of fines (<74 μm), the more important that the agglomeration product satisfies some minimal requirements. This paper presents an agglomeration scale that identifies the quality standards for agglomerates and documents the resulting mechanical, physical, and hydraulic (hydrodynamic) behavior associated with each level on the agglomeration scale. The hydrodynamic properties of an agglomeration product are critical for the proper design of a leaching operation and, as shown in this paper, can be used to select the optimal pretreatment method for a given ore sample. Agglomeration as a unit process not only allows better conditioning of the hydrodynamic behavior of the ore but also creates an opportunity for optimized delivery of reagents to kick-start the leaching process which may ultimately improve the economic performance of leaching. Industrial case data is used to demonstrate the shortfalls associated with low-quality agglomeration and the benefits of improved agglomeration which range from enhanced porous structure (better percolation and drainage characteristics) to better metallurgical response (faster kinetics and higher metal recovery). Proper agglomeration has been used to render otherwise untreatable ores into valuable leaching resources.

Feb 9, 2024

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By Jennifer L. Bell, PATRICK L. YORIO, Emily J. Haas, Susan M. Moore, Lee A. Greenawald

Although researchers have struggled to replicate Heinrich’s safety triangle findings (Heinrich 1931) for various reasons (e.g., no access to his original database and it is unclear if the database was of a single establishment/operation or for an entire industry), the occupational safety community has continued to adopt and expand the applications of this theory (e.g., McSween 2003). Within the mining industry, the potential exists for operations and companies to use concepts from the safety triangle as a way to inform or challenge the practices employed within their health and safety management systems (HSMS) to prevent incidents (Backlund 2016). This paper considers data obtained from the Mine Safety and Health Administration’s databases and demonstrates the validity of applying the safety triangle theory at the mine level. The results support the use of this theory and demonstrate that lower severity incidents can predict fatalities in a subsequent year where significant nuances and caveats to applying the theory are identified and discussed.

Jul 25, 2020

By Robert Burgess, Dale Gill, Jaco Steyn, Bill Kyslinger

"With mining, especially coal extraction, comes the necessity of supporting the roof. Since the 1950s, the primary method for roof support has been the use of roof bolts. Roof bolting is considered one of the most hazardous jobs in underground coal mining. In 2004, there were 3,405 injuries reported to the U.S. Mine Safety and Health Administration (MSHA). Of those injuries, 17 percent were associated with bolting machines (593 injuries). The majority of the injuries resulted from rock falling from supported roof. However, injuries involving a part of the body being struck by, or caught between, during bolting and drilling occurred with relatively high frequency (Burgess and Steiner, 2007).Roof drilling and bolt installation is labor-intensive and repetitive. These labor-intensive and repetitive requirements can lead to cumulative trauma. Operators are expected to perform a considerable amount of lifting, carrying, bending, reaching and stretching. Back and shoulders become sore from bending and twisting to install bolts or lift and position drill steels, wrenches and bolts. Confined operator spaces also contribute to difficult and awkward working positions for the operators (Cornelius and Turin, 1998).In South Africa, the majority of the roof bolting machines used are “man-in-position” style machines (Fig. 1). This puts the operator in close proximity to where the drilling and bolting process is performed. When proper operation procedures are followed, it has been proven to be a very effective, productive and safe system. The MSHA-certified automatic temporary roof support (ATRS), canopies and dust collection system of Fletcher bolters all provide the operator with unparalleled protection. However, there are some occupational hazards inherent to the zone located next to the drilling and bolting zone. This has led some customers to request relocating the operator away from this zone. The idea being that the operators will no longer be located in the face area, greatly reducing their exposure to dust, noise, machine and geological hazards."

Mar 1, 2017

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By P. Mousset-Jones

The USBH Mining Systems and Ground Control Generic Research Center funded a project leading to the improved planning of airflow and refrigeration in underground mines experiencing hot working conditions. The project was broken down into approximately five phases: 1. Visiting some of the known hot mines in the U.S. and sending out a questionnaire to determine other mines which might be experiencing hot working conditions in the future. 2. Choosing two mines in which to conduct measurements to determine the insitu rock thermal conductivity and diffusivity, and comparing these values with laboratory determined values. 3. Investigating computer programs available for mine climate simulation, and testing these programs with case study examples from the two mines where the rock thermal properties were measured. 4. Considering improved ways of estimating the wetness factor and experimenting with the use of heat flux meters to more directly measure the rock heat inflow into the airstream. 5. Applying the results of these investigations to simulating the climate for future mine development and production areas at the two- mines. The project is approximately two thirds completed. At the time of writing, the insitu measurements at one of the mines are still being recorded. This paper will be describing the procedures and results of the insitu rock thermal property measurements, and give a brief description of some of the simulated results obtained for a mechanised cut and fill stope case study from the Homestake Gold Hine in South Dakota.

Jan 1, 1985

By David M. Lake

Conversion to trolley assist is a means of minimizing diesel fuel consumption, which in many mining situations offers a rapid payback of capital investment plus the inherent flexibility and maneuverability of truck shovel operation. When diesel electric truck shovel mining operation with trolley assist is compared to alternative mining methods such as conveyor systems, the trolley assist system can be easily justified in terms of return on investment, payback and increased productivity. A review of present technology, performance requirements and past experience in the mining industry has led to the development of a trolley assist system for diesel electric haulage trucks which, is proven in the mining environment, offers significant reduction in fuel consumption and increased productivity.

Jan 1, 1981

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

By D. R. Tesarik, T. C. Trancynger, W. G. Pariseau

The Davis detector cavern was excavated on the 4850 Level of the former Homestake Mine in the mid- 1960s to house a novel neutrino detector developed by Nobel Prize winner Dr. R. Davis. The original cavern was about 9.1 x 16.8 x 9.7 m high, excavated in a Precambrian amphibolite known as the Yates unit and enlarged in 2010. In 2009, the National Science Foundation selected the site for development as a national Deep Underground Science and Engineering Laboratory (DUSEL). This retrospective rock mechanics study of the Davis cavern is intended to inform design of the much larger caverns and laboratory rooms being considered for the same 4850 Level. Provision for rock mass variability, sequential excavation, jointing and wall damage from blasting are included in analyses that were done using two different computer codes and methods (FLAC3D and UTAH3). The results are in agreement with observations and show that cavern stability is indeed the case. The main conclusions are: (1) if conventional scaling of laboratory rock elastic moduli and strengths is done, then 0.25 and 0.50 scale factors are reasonable, (2) measured statistical and spatial variability in rock properties should be incorporated into geomechanical analyses to better reflect reality, (3) discontinuities (“joints”) are essential to reliable analysis of excavation safety and when properly taken into account eliminate the need for empirical “scaling” of laboratory rock properties, (4) major geologic features such as rhyolite dikes and breccia zones may be important to excavation safety at Homestake and should be explicitly represented in analyses and (5) quantifying wall blast damage is important to engineering design of underground excavations.

Jan 1, 2012

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By L. J. Hoover

The objective of this study was to assess the health and environmental impacts of fluidized-bed combustion (FBC) of coal, specifically as applied to baseload generation of electrical energy by utilities. The study* was a short-term effort that based its analyses on information derived from the experience of the group or quickly obtained from the literature. The approach was to compare Atmospheric Fluidized-Bed Combustion (AFBC) and Pressurized Fluidized-Bed Combustion (PFBC) with two current technologies: low-sulfur coal combustion (LSC) and flue gas desulfurization (FGD) used with high-sulfur coals. A wet-limestone process was selected as the FGD technology. The impacts compared involved not only health and environment but also sociology, resource use, and dollar cost. Conditions for comparison were centered around a nominal date of 1988, when initial operation of commercial AFBC plants may occur. The PFBC has a later introductory date, a nominal 1995 (its impacts relative to other competitive technologies now in the R&D stages were not compared.)

Jan 1, 1978

By Karin Bäppler

A new polyhalite fertilizer mine is currently being developed in the UK by Anglo American Crop Nutrients. The project includes the construction of a Mineral Transport Tunnel almost 37 kms long to house a conveyor belt that will move polyhalite from the production shaft at the mine to a materials handling facility at the port. The project sets a new standard in terms of an ultra-long tunnel drive and sustainable, environmentally friendly and efcient material transport. The paper highlights in particular the . m diameter TBM in use for the construction of the ultra-long tunnelling section.

Jun 23, 2024

By C. Vasilescu

Phytotechnologies use plants to remediate various media impacted with different types of contaminants. These technologies can be implemented either in situ or ex situ. The affected media in which phytotechnologies can be applied include soil, sediments, groundwater and surface water. They are best applied at sites with shallow contamination of organic, nutrient, or metal pollutants that are amenable to one of five treatment options: phytoextraction, phytotrans-formation, rhizosphere, bioremediation, phyto-stabilization or rhizofiltration. Phytoremediation can be used along or, in some cases, in place of mechanical cleanup methods. Phytoremediation can be used to clean up metals, pesticides, solvents, explosives, crude oil, polycyclic aromatic hydrocarbons and landfill leachates.

Jan 1, 2006

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By Gang Yang, Manchao He, Chengzhang Gao, Jun Zhang, Yayun Li, Jun Yang, Shilin Hou, Ben Liu, Yajun Wang, Jianning Liu

To explore the mechanism of roof directional breaking in gob-side entry formed automatically without coal pillars, the numerical simulation was used to study the deformation movement of roof, the deformation evolution of roadway, and the stress distribution of roadway under roof directional breaking and non-roof directional breaking. Based on the results, the deformation movement of roof is divided into three stages: the goaf roof collapse stage, the basic roof deformation stage, and the basic roof stability stage. The goaf is filled with gangue due to the broken expansion characteristics of the collapsed rock under the roof directional breaking. Due to the supporting force of gangue, the deformation of the basic roof under the roof directional breaking is smaller than that under the non-roof directional breaking, which reduces the influence of the deformation of the basic roof on the deformation of the roadway roof and improves the integrity of the roadway. At the same time, roof directional breaking cuts off the stress transfer path of partial roof, which weakens the peak stress convergence on the arc side, transfers the peak stress convergence to deeper, and improves the stability of roadway. Finally, a field test was carried out to further verify the accuracy of the numerical simulation. The field test results are in good agreement with the numerical simulation results. The roadway deformation is small and meets the requirements of safety production. It is proved that roof directional breaking plays a positive role in improving the stability of the roadway.

Dec 22, 2022

By Kevin A. Foo, Murray D. Bath, John H. Canterford, Arnaldo Ismay

There is no doubt that the dominant future source of gold will be the so-called refractory ores, especially those with gold in a pyrite/arsenopyrite matrix. Minproc Engineers is taking an active role in establishing detailed design criteria for a number of apparently competing processes. This involves generating a detailed understanding of the metallurgy involved, systematic pilot plant testing, and the application of advanced engineering technologies. This presentation outlines the approach adopted by Minproc as well as the design criteria for several current projects.

Jan 1, 1989

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By Brianna M. Eiter, Jennica L. Bellanca

Mineworkers face a challenging and dynamic work environment every workday. To maintain a safe workplace, mineworkers must be able to recognize worksite hazards while they perform their jobs. Though hazard recognition is a critical skill, recent research from the National Institute for Occupational Safety and Health (NIOSH) indicates that mineworkers fail to identify a significant number of hazards. To further the understanding of mineworkers’ hazard recognition ability and to begin to address hazard recognition performance, NIOSH researchers analyzed data collected during a laboratory research study to determine the effect of individual mineworker factors including risk attitude, work experience, and safety training on hazard recognition accuracy. The results of this study show that mineworker risk attitude and safety-specific work experience affect hazard recognition performance while hazard-specific safety training does not. These results suggest that some of these individual factors can be overcome through experience and training. Potential strategies that can be used to address these factors are also discussed.

Aug 31, 2020

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, have been widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using total station which is time-consuming and inaccurate especially on small scale models. A photogrammetry-based measurement system has been developed. During a physical modeling process, photos of the model can be taken during the simulation process reducing survey time from hours to a few seconds. A program, Photogrammetry Analysis for Physical Modeling of Mine Subsidence Process (PAPMMSP), developed based on photogrammetric principle is used to quickly identify the installed observation points and accurately determine their coordinates. The measurement accuracy is well under submillimeter level—an ultra-important advantage as any measurement errors in coordinates are magnified by the model dimension scale (commonly 20 to 400). A physical modeling case of subsurface strata movements and deformations associated with longwall mining operations is presented in the paper to demonstrate the functions and capabilities of the developed photogrammetry program.

Aug 11, 2020