Search Documents

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By R. Hipsley, D. Arbonies, P. J. Dobak, M. Visher

The Storm deposit is a high grade breccia hosted “Carlin-type” gold deposit located at the north end of the Carlin Trend. Storm consists of 3 smaller deposits: 1) 49er Zone, 2) End Zone, 3) Discovery Zone. Structural intersections and favorable stratigraphy at the Paleozoic Popovich/Rodeo Creek formation and Bootstrap limestone formation contact are the primary known controls to gold mineralization at Storm. High grade silica-sulfide breccia occurs in the footwall of the north-south trending, dike filled, Dee fault. This mineralization cross-cuts silicified heterolithic breccia zones localized above the Bootstrap limestone where northwest, dike filled, reverse faults cut this structural-stratigraphic horizon. 40Ar/39Ar dates of 37.57+ 0.34 Ma (basalt dike) and 162 Ma (lamprophyre dike) have been obtained from dikes in the Dee pit which are locally mineralized by the same event as Storm. This paper will focus on the descriptive aspects of the Storm deposits.

Jan 1, 2001

By A. Robles-Vega

In recent years, tellurium has been extensively used in the manufacture of semiconductor materials. For this type of application, high-purity tellurium is required. Selenium, lead and silicon are usually the main impurities in tellurium. During the electrolytic refining of copper, tellurium gold and silver are collected in the anode slimes. A pyrometallurgical treatment is used to recover gold and silver from the decopperized anode slimes whereas tellurium is oxidized and skimmed off from the refining furnace as a Na2CO3-based slag. In the slag, tellurium is present as sodium tellurite (Na2TeO3), which is further water-leached from the slag. The first step in the conventional process for tellurium recovery consists of the precipitation of the tellurium contained in the leaching solution as tellurium dioxide (TeO2). The solid TeO2 is then dissolved under acidic conditions for its further reduction with sulfur dioxide gas (SO2). In this paper, an alternative route for tellurium production is presented in which a sodium tellurate [Na2TeO4] intermediate is obtained by oxidation of the sodium tellurite in an alkaline solution following the water leaching step. Sodium tellurate is then dissolved in acid media and high-purity tellurium is obtained by reduction with SO2 gas. Experimental tests under laboratory conditions indicate that the novel process yields higher precipitation selectivity for tellurium than the conventional process. A comparison of its efficiency concerning impurities co-precipitation with respect to the conventional process is discussed.

Jan 1, 2009

By K. E. Wood, K. J. DiRocco, L. A. Becker

The Russia Wharf segment of the Silver Line Phase II Project for the MBTA incorporated ground freezing and underpinning during New Austrian Tunneling Method(NATM) tunneling through timber pile foundations, urban fill, and abandoned wharf structures beneath two historic 7-story buildings with steel frames and masonry facades. During construction, the project team implemented an extensive program to monitor, evaluate, and mitigate the ground and building movements caused by the various construction activities. Mitigation included freeze cycling and building raising/lowering to compensate for ground movements and safely maintain the serviceability and occupancy of the buildings. In this paper, we present the history of the freeze, tunnel construction, and thaw-related movements that occurred and the building response that we observed.

Jan 1, 2005

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008

By H. Lowers, B. Van Gosen

The Iron Hill (Powderhorn) carbonatite complex is a 31 km2 alkalic intrusion located about 35 km south-southwest of Gunnison, Colorado. The intrusion has been well studied and described because of its classic petrology and architecture of a carbonatite-alkalic complex. The complex is also noteworthy because it contains enrichments of titanium, rare earth elements, thorium, niobium (columbium), vanadium, and deposits of vermiculite and nepheline syenite. In particular, the complex is thought to host the largest titanium and niobium resources in the United States, although neither has been developed. It may be economic to extract multiple resources from this complex with a well coordinated mine and mill plan.

Jan 1, 2007

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

By David A. Brence, Andrew D. Marti, Richard P. Stahura, Ronald J. Valentine

The development of an effective belt-cleaning system for a new conveyor system seemed a fairly conventional assignment. But a closer examination of the project showed a number of “fine print” details: •High altitude location (with resulting cold weather and low humidity conditions). •Long conveyor length. •Troublesome material (very sticky and capable of hardening like concrete). •Limited water. These difficulties are spelled out the challenge of developing a cleaning system for the production conveyor2 (PC2) belt at Climax Molybdenum’s Henderson Mine.

Jan 1, 2005

By J. Sandford, S. Hennings

EXECUTIVE SUMMARY An approach borrowed from the petroleum industry was applied to the gas development evaluation for the Bulga underground coal mine in New South Wales, Australia. The results enabled the coal mine operator, Xstrata Coal, to systematically plan the extraction of gas in harmony with mine production planning of multiple coal seams. This has allowed for a more proactive approach in preparing the resources and infrastructure needed to capture the gas and accelerate coal mining while maintaining their high level of commitment to safety. Norwest has for decades used gas recovery simulation models to assist the petroleum industry and the coal bed methane (CBM) industry in understanding and forecasting fluid saturations and flow behavior. Norwest developed a similar process with Xstrata to migrate existing mine data at Bulga into reservoir simulation models to study various drainage alternatives. An interesting feature to the evaluation was also developing an understanding of test procedures and nomenclature from the mining industry to properly translate the data for input in simulators developed for the petroleum and CBM industries. The model was then calibrated to actual field data collected from drainage pilot tests that Norwest helped design and monitor at Bulga. The resulting calibrated predictions were then used to develop budgets, schedules, resource requirements, and alternatives for capturing the gas and delivering it to market ahead of mining. Increasing revenue, reducing emissions, improving schedules and cutting costs for the mining operations have all contributed to justifying this advanced approach at Bulga. It has also allowed Xstrata to expand their focus to the sizable gas reserves in seams not currently planned for mining. Several of these seams would be economic gas development targets once the gas recovery infrastructure is installed for the mine. The evaluation process was refined throughout this project and the resulting approach will benefit Xstrata with their broader strategic development of resources in the Hunter Valley and beyond to their worldwide operations.

Jan 1, 2007

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

By Isabelle Lamb, Manfred K. Lechner, Daniel N. Adams

Sydney Australia’s M5 East Motorway connects southwestern suburbs to the airport. Central to the project are twin 3.8 km roadway tunnels which are mostly driven through rock. In order to come up with the winning tender, the project team developed several unique approaches for tunnel excavation and support. The project’s flat roof with thin shotcrete lining, 20 m wide underground intersections, thixotropic-grout sheathed rockbolts and cablebolts, and new shotcrete testing methods all differ significantly from traditional concepts. This paper presents the design basis and construction methods used to achieve the 100-year design life required by the project’s owner.

Jan 1, 2001

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By M. Mikhaylenko

Rhenium, molybdenum and tungsten are the elements demanded by high-end technologies. These metals are found in process solutions in forms of their oxyanions: ReO4-, MoO42- and WO42-. The later two can exist in forms of iso- and/or heteropolyanions. Basically all three metals demonstrate very similar chemical behavior in aqueous solutions. Unfortunately, in their mineral sources these elements commonly accompany each other, like pairs of rhenium-molybdenum or molybdenum-tungsten. Their economical separation is a challenging task.

Jan 1, 2012

By A. B. Cecala

A few years ago, the National Institute for Occupational Safety and Health and Unimin Corporation developed a clothes cleaning system that is able to quickly, effectively, and safely remove dust from a worker?s clothing without dust exposure to the worker, the work environment, or co-workers during the cleaning process. To perform the process, a worker enters a cleaning booth and activates an air spray manifold which blows the dust from the worker?s clothing. Since the cleaning booth is under negative pressure, all the dust and product removed are contained. In the original design, this dust-laden air was exhausted to a dust collector system. However, since most operations do not have excess dust collector capacity, it was decided to determine an alternative method to provide for a stand-alone cleaning system. This was achieved by ducting the exhaust outside the plant and into the atmosphere. This technique was recently tested and shown to be a viable method to provide for a stand-alone clothes cleaning system.

Jan 1, 2009