Search Documents

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By Greg Partington, Darryl Thorburn, Charlene Wildman, Elisa Puccioni, Connie Payne, Campbell McKenzie

"Mineral prospectivity modelling of polymetallic nodule deposits has been completed over the Cook Islands Exclusive Economic Zone (CIEEZ) using the GIS based Weights of Evidence modelling technique. Polymetallic nodules, also known as manganese nodules, have been explored as a possible resource for a number of metals including cobalt since the early 1970s. Recent data on the nodule composition and abundance in the CIEEZ has led to a renewed interest in the prospectivity for manganese nodules in the region. The predictive modelling has used the most recently accepted mineral model for polymetallic deep-sea nodule deposition to identify factors that are most likely to map the presence of this type of mineralisation in the CIEEZ.Manganese nodules form on the deep seafloor as concretions formed by concentric layering of iron and manganese hydroxides around a core and they grow at a very slow rate, on the order of millimeters per million years. The available data for the CIEEZ indicates a greater abundance in the area of nodules formed by hydrogenetic processes, which are the result of slow precipitation of metallic components from seawater. The environment in which the nodules are most abundant is at depths between 4,000 m and 6,000 m in areas of low sedimentation rate. Hydrogenous nodules commonly grow on siliceous and pelagic clay sediment, they are less common on other types of sediment."

Sep 1, 2014

By Vhutali Carol Madanda, FHATUWANI SENGANI, François Mulenga

The first introduction of fuzzy theory in the nineteenth century created room for continuous research and application in various fields. Fuzzy set theory has been globally applied in geotechnical engineering, and research in this field continues to date. The fuzzy inference system is considered to be one of the most popular techniques adopted to resolve some of the geomechanical challenges faced in both surface and underground excavations. This paper unpacks fuzzy theory-based approaches in mine geomechanics with the aim of expanding the innovative application of the same approach specifically in tunnel geomechanics. This aim was achieved by conducting a review of recent successful and unsuccessful applications of fuzzy inference systems in underground excavations/tunnelling geomechanics. Indeed, this review has outlined some cardinal points associated with the ability of the technique to solve complex geomechanics problems. However, the success of the technique was accompanied by a few limitations associated with the methodology. Finally, a future outlook associated with the technique has been established.

May 15, 2023

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By Andrew Stafford, Kate Willa Brown Requist, Eric Lutz, Simon Lotero Lopez, Moe Momayez, Jeffrey Gordon

This formal literature review identifies strengths and shortcomings of current literature related to mine rescue, self-rescue, and self-escape technology. Key concepts and factors that influence the decision making behind mine rescue and self-escape were identified. Historically, underground mining has been one of the most dangerous occupations due to the harsh nature of working environments. During the latter half of the twentieth century, and into the twenty-first century, mining fatalities have declined, yet large-scale mine emergencies persist. The emergence of new technologies, in combination with evidencebased mine emergency research, is resulting in new training methods, monitoring systems, and self-escape approaches being tried in operating mines. This review identifies areas in which substantial research is being conducted, such as the use of virtual reality and game-based training and areas that warrant further development such as the measurement and information gathering capabilities of unmanned ground and aerial vehicles, as well as emergency management and incident command systems. This paper summarizes the current underground mine rescue and self-escape landscape in the USA, including the breadth and depth of mine rescue and self-escape training and practices as evident in the literature.

Nov 2, 2023

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

By S. Frimpong

Cable shovels are used for primary excavation in in-situ and/or pre-fragmented formations in surface mining operations. Poorly fragmented hard rock formations and random occurrence of hard boulders in soft formations cause extreme variability of material diggability, resulting in varying shovel stress loading. The stress loading of a shovel’s front-end assembly could result in fatigue failure. Conventional design process, which uses physical shovel simulation studies, is very costly and time consuming for achieving statistically significant results. In this paper, rigid and flexible multi-body dynamic theories are used to develop component stress loading and deformation models of the cable shovel, and solved in the ADAMS/NASTRAN/FLEX environments. Detailed simulation experiments are carried out to examine the performance, reliability, durability and efficiency of the P&H 4100A under varying in-situ formation conditions. The results show areas of high stress fields with a maximum stress of 313.31 MPa at node 441 within the hoist rope. The reliability of the results is confirmed by comparing existing test data. The study is significant because it provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2007

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By J. D. Lowell, L. Quevedo

I will talk today about a porphyry copper exploration program now underway in the Amazon jungle in the southeastern part of Ecuador near the border with Peru. The project is unusual for two reasons: first the deposits are of Jurassic age, 153 m.y.o., which is unusually old for porphyry copper deposits and they may be the most significant pre-Tertiary age porphyry deposits known. Second, the district was found only six years ago which makes this the most recent discovery of a totally new porphyry copper district. The new porphyry district, known as the Zamora River Copper Belt, or the Corriente Copper Belt, is a north trending area 50 km long by 10-15 km wide, which is nearly aligned with the axis of the Jurassic age Zamora batholith and with the course of the Zamora river. Gencor in 1994 initiated a regional grassroots gold exploration program based on reconnaissance geologic mapping and geochem sampling which did not find a gold mine, but which identified the San Carlos porphyry copper system in April, 1995. In a later reorganization between Gencore and Billiton the Ecuador project was transferred to Billiton and between the Gencore work and Billiton’s a total of 10 porphyry copper systems were found over the next four years. In the period of 1997 - 1999 Billiton drilled a total of 11,000 meters of wide spaced core holes in the San Carlos, Panantza and Kutukus prospects. In October 1999 Billiton concluded a farm-out, joint venture agreement with Corriente Resources and Lowell Mineral Exploration for additional exploration of the Zamora property. This is funded by Corriente and managed by Lowell Mineral Exploration and a total of 28,000 m of core drilling was completed through August 2001. An immediate result of the Corriente Lowell project was the discovery of potentially commercial ore reserves in two new deposits at Mirador and Warintza. Additional closer spaced drilling was done in the Panantza deposit and additional drilling is planned at San Carlos, in targets related to Warintza, and elsewhere.

Jan 1, 2002

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Southwestern New Mexico is part of a large belt of Late Cretaceous to Eocene copper porphyry deposits found in Arizona, New Mexico, and Mexico. These deposits are the result of arc magmatism that occurred during the Laramide orogeny. Recently, attention has been brought to other commodities that can be extracted as by- and co-products, many of which are critical minerals. A new compilation of the geochronology of these deposits shows two main pulses of magmatism that produced mineralized deposits and, along with new dates by the author, shines new light on the geologic history of these deposits and the role it plays in critical mineral abundance.

Feb 1, 2024

By Ayokunle Adewale Akinlalu, Sunday Bayode, Sherif Olumide Sanusi, Joshua Oluwagbenga Adeboye

Gold occurrences have been reported in Alagbede, southwestern Nigeria, but a mineral potential map (MPM) to guide academics and investors in the area is still needed. As a result, geophysical methods (aeromagnetics and aero-radiometry) have been used to assess the potential for gold minerals in the area. Several enhancement filters, such as reduction to the equator, upward continuation, analytical signal, second vertical derivative, and power spectrum analysis, were applied to the aeromagnetic data to understand the subsurface geology better. The enhancement filters applied to airborne radiometry data are K/eTh, ternary color composite, F parameter, and deviation from the ideal K values (Kd). Geophysical data analysis was used for structural mapping and geological reconstruction, while aero-radiometric data was used for hydrothermal alteration mapping. The primary trend observed in the area’s magnetically inferred structural framework map is NE-SW, while a few are in the NW–SE and E-W trends. These observed trends show that the study area suffered at least three deformation episodes. Geological evidence of gold mineralization, such as favorable lithology, geological structure, and hydrothermal alterations, has been fused to produce a reliable MPM of the area. The geographical location of the existing mineral sites in the investigated area agrees with the geological structures and the MPM produced there. Thus, the systematic approach adopted in this study can be extended to other supracrustal belts of a typical Precambrian basement complex worldwide to ensure the reliability of orogenic gold mapping and resource management.

May 9, 2023

By M. H. Basiri

The application of aluminum matrix composites, due to their unique properties, is significantly growing in the variety of industries such as aerospace and automobile. In comparison to other light metals, such as magnesium and titanium, aluminum is lower in price. These are the advantages that this metal dominates the others. In this research, first by applying the lost foam casting method, the SiCp/A356 composite was cast in the bottom and side gate conditions with 690°C and volume fraction of 10%. Furthermore, the effects of reinforcement particles (60 µm, 75 µm) were examined. The results present the particles distribution in the side gate methods is more homogeneous than the bottom gate casting method. Also, by increasing the particles sizes, the fading rate in the side gate are reduced from 22% to 19%, as well as from 26.4% to 25.4% in the bottom gate. Key words: Carbide-Silicone Particle, Gating System, Composite Micro-Structure, Foam Casting

Feb 27, 2013

The Río Agrio of northern Patagonia, Argentina, is highly acidic due to inputs of volcanic gases (SO2, HCl, HF) in its headwaters. The watershed includes a hyper-acidic (pH <0.5) volcanic crater lake, a larger glacially carved lake that is also strongly acidic (pH 2.6 to 2.7) and an acidic river that flows for more than 40 km (25 miles) before its pH is completely neutralized. This unique watershed has many geochemical and biological similarities to acid waters caused by mining. This paper describes the Río Agrio watershed and draws a comparison with some famous acid mine waters. Learning more about naturally acidic lakes and river systems could have important applications to the bioleaching of ores or biological treatment of mine waters. Therefore, it should be of interest to the general community of mining and metallurgical engineers.

Jan 1, 2008

By Louis W. Cope

Mongolia is known in western countries as the location of rich dinosaur fossil fields. However, the country is even richer in mineral resources. The Ministry of Industry and Trade reports 6,000 mineral occurrences of 80 metals and minerals. Mongolia has already attracted much foreign investment in the mining sector. Mining is the country’s largest industry. It is responsible for 17 percent of the gross domestic product, 65 percent of industrial output and 57 percent of export earnings.

Jan 1, 2006

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021