Search Documents

By G. Tranell, L. Kolbeinsen, S. Gaal, J. Safarian

The effect of carbon material properties on the rate of MnO reduction from ferromanganese slag by solid graphite was investigated. A sessile drop technique was used to study the reduction rate of a synthetic slag containing 45 wt% MnO at 1500 and 1600 ºC. Different types of graphite substrates were used and the con-tact angle between slag droplets and substrate were measured in-situ. Moreover, the slag droplet volume during the interaction with the graphite substrates was calculated and normalised. The mathematical relationship between the slag density during the reduction and the normalised slag droplet volumes during the reduction were derived and the MnO reduction curves were then calculated. A method for measuring the slag reactivity of solid carbon was defined and used to qualify the propensity of the different graphites to react with the liquid slag. Some supplementary studies such as manganese evaporation measurement and EPMA analysis for determining the extent of MnO reduction were also carried out. It was observed that there is nota significant difference in the wetting angle of the graphite substrates by the slag, and the wetting is not changed within the temperature range of 1500-1600ºC. However, the changes in the contact angle during the slag reduction at 1600ºC are more than at 1500ºC. The kinetics of MnO reduction is dependent on the type of graphite and it is more dependent on the graphite properties at lower temperatures. On the other hand, the dominant properties of graphite on the reduction rate vary with temperature. A multivariate analysis on the graphite properties and the parameters related to the slag reactivity indicated that the kinetics of MnO reduction is mainly dependent on the temperature, and then on the graphite properties. It was also found that at1500 ºC the surface area and the CO2 reactivity are the most important graphite properties for the slag reduction, suggesting that the reactivity of carbon is rate controlling at 1500 ºC. However, the porosity related parameters are the most important graphite properties at 1600 ºC, suggesting that CO gas desorption is rate controlling at high temperatures.

Jan 1, 2007

By M. H. Rogers

Coal has been at the forefront of mankind?s drive to improve his quality of life and also for sustainable development, from the Industrial Revolution onwards. The international coal industry today is large, with some 3,7 billion tons being produced and consumed in 1997. South Africa is an important participant in the coal industry, selling some 220 million tons in 1997 of which 64 million tons were exported. It is the second-largest thermal coal exporting country in the world. Despite the size of the world coal industry, it is not immune to change. The address examines growth projections for the industry and the change drivers that will impact on it in the future. Environmental pressures, the most important of which being the climate change debate, the Kyoto Protocol arising from this debate and the development of clean coal technologies, to reduce the impact of coal production and usage on the environment are considered. Other major change drivers considered are competition from other sources of energy and that between coal producers, the deregulation of the electric power industry, corporate restructuring and for the South African producer, legislative reform. The declining (real term) coal price, the consequent squeeze on margins and the need for producers to actively contain costs is covered. Technology has, in the past, been the driver behind the growth and change of the South African coal industry and its future role in ensuring that coal is the fuel of choice for continued improvement in standards of living and economic development is addressed.

Jan 1, 1999

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002

Changes in reductant and energy inputs which are required to adjust the slag composition in anilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input does also hold for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003

By Q. G. Reynolds

DC arc furnaces are widely used for steel scrap melting, and are increasingly being used for smelting applications as well. The electrical resistivity of slags varies widely, from highly conductive slags in ilmenite smelting, to highly resistive slags in applications such as cobalt recovery from non-ferrous slags, and nickel laterite smelting. Models have been developed to predict the electrical behaviour of the DC open plasma arc and the molten slag bath. These models allow the voltage and current ranges of furnace power supplies to be specified.

Jan 1, 2004

By Peter W. Lotz

Contents of: ?Sampling for Cyanide in Metallurgical Processes? ?Sampling at process level of operation ?Sampling at environmental level ?Sample stability and integrity issues ?each citing possible objectives, practical example and reasons for surprises Overall recommendations on sampling plans and procedures to maintain sample integrity

Jan 1, 2005

By P. J. Lloyd

There are few data on the composition of discard coal in South Africa, and no overall view of the discards for the entire industry. As a result of work on coal qualities in South Africa, a database was established which enabled a good estimate to be made of the composition of the discard from every mine. The data are presented in the form of histograms of ash, volatile matter and fixed carbon content of the 43 million tons of material which were discarded in 1990. The results are discussed in terms of the closeness of the composition of much of the discard material to presently used power station coal. It is concluded that it is mainly developments in equipment, particularly fluidized bed boilers, which inhibit the wider use of discard coal. However, other factors must be noted, including the relatively high sulphur content of the discards, and the fact that even with the most careful storage the material ages and may become unusable after about 15 years.

Jan 1, 2000

By R. P. H. Willis

For technology transfer to be successful a process, from research to full scale application, has to be followed. This paper describes such a process and how it is applied in practice. Some of the ?do?s? and ?don?ts? are highlighted. Recommendations are made on how to communicate existing knowledge and to ensure that a framework exists to effectively plan future projects with final technology transfer objectives firmly in place. The Impact Ripper System is used as a case study to illustrate lessons learned. Key words: Technology transfer, implementation

Jan 1, 2002

By R. J. Durheim

Detailed investigations have been conducted into 21 rockbursts which caused damage to excavations in deep South African gold mines, in many instances resulting in the death or serious injury of workers. The objective of this study is to determine the principal factors controlling the severity and distribution of damage, so that strategies to reduce the hazard of rockbursts may be developed. It was found that the source mechanism is often controlled by the mine layout, and regional structures such as faults and dykes; while local rock conditions and support systems strongly influence the location and severity of damage. In the short term the most important lever for reducing the rockburst hazard is the effective implementation of existing rock engineering knowledge and technology.

Jan 1, 1998

By J. L. Human, N. Fernandes

The rockfall hazard is the major contributing agency to fatal accidents in South African platinum mining operations. The majority of these accidents occur in close proximity to the working stope face. The collapse of fractured or blocky ground between individual temporary support units or the closest permanent support line to the stope face has not yet been adequately addressed. A large-scale stope support system testing facility funded by the Safety in Mines Research Advisory Committee (SIMRAC), has been designed and constructed to test support systems and stimulate innovative thinking by mining personnel, support manufacturers and suppliers by providing a facility where the interaction of stope support systems, a rigid stope face and a discontinuous hangingwall beam can be observed during quasi-static and dynamic conditions. Tests have been carried out on various types of stope support systems, focusing on the temporary support systems used in the immediate stope face area. The interlinking of the temporary support units with mesh or safety netting has been explored in the prevention of falls of ground between support units during gravity driven falls of ground. These tests illustrate the facility?s ability to be used to stimulate innovative thinking and provide a testing ground for the development of temporary support systems in order to reduce the risk off all of ground injury to mining personnel at the stope face.

Jan 1, 2004

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African platinum group metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky Reef is low in chromium and does not pose significant melting problems. Concentrates from the UG-2reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8?10-9bar at temperatures of 1550°C to 1600°C). During the converting process, care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation of Fe2NiO4 (trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever-increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3.A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Keywords: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium

Jan 1, 2004

Outsourcing of specialist and non-continuous services is common practice in international mining operations. There is an increasing trend towards this practice in South Africa as a result of the major organisational changes that have taken place in the industry, and as lower revenues and production cost pressures have reduced profit margins. Many specialist functions have been outsourced in the industry for a long time, an example being shaft sinking, which is undertaken by specialist shaft sinking contractors. In the professional services area, some activities have been outsourced, for example the design and construction supervision of tailings dams, but mining related activities such as geology, mine planning and scheduling, engineering, ventilation, and rock engineering, have traditionally been carried out by in-house staff. In this paper some of the industry problems which have led to an increase in outsourcing of professional services are considered. Then the pros and cons of outsourcing are dealt with before outlining the factors which should be taken into account in choosing an outsourcing partner.

Jan 1, 1999

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By D. M. MacHunter, T. Lawson, D. K. Henderson

The development and commercialization of new generation high tension electrostatic separators has provided a basis for simplifying mineral separation plant circuitry. The inclusion of new design features including insulated plate electrodes that have resulted insignificantly improved separation efficiencies in electrostatic separators are described. The increase in separation efficiency has resulted in a reduction in the number of treatment stages required to produce final high grade mineral products. Comparative performance data on different feed types are presented. A comparison between mineral separation plant flowsheets using both conventional and new generation high tension electrostatic separation technology is presented. A 55% reduction in the number of installed electrostatic separators and a 36% reduction in plant area was achieved through the use of this new electrostatic separation technology.

Jan 1, 2003

By C. Erichsen, J. Werfling

ABSTRACT: A three-dimensional elastic constitutive model for rock salt is proposed. This stress strain law takes into account the three phases of creep (transient, steady state and accelerated creep), dilatancy, as well as the failure and post failure behaviour. The model was implemented into a finite element program and validated on the results of laboratory tests and in situ measurements. A good qualitative and quantitative agreement with the test and measurement results is achieved. A stability analysis for an underground repository in rock salt is presented. ZUSAMMENFASSUNG: Es wird ein dreidimensionales elastisch-viskoplastisches Stoffgesetz für Steinsalz vorgestellt. Mit diesem Stoffgesetz können die drei Kriechphasen (primäres, sekundäres und tertiäres Kriechen), Dilatanz sowie das Bruch- und Nachbruchverhalten erfaßt werden. Dieses Modell wurde in ein Rechenprogramm, das auf der Methode der finiten Elemente basiert, implementiert und an Ergebnissen von Laborversuchen und in-situ-Messungen validiert. Die Versuchs- und Meßergebnisse lassen sich mit diesem Stoffgesetz qualitativ und quantitativ gut nachvollziehen. Als Anwendungsbeispiel wird der Standsicherheitsnachweis für eine Untertagedeponie im Steinsalz erläutert. RÉSUMÉ: Cet article présente un modéle constitutive élastique/viscoplastique à trois dimensions pour sel gemme. Ce modéle comprend les trois stade de fluage (fluage primaire, secondaire et tertiaire), la dilatation, le comportement de défaillance et d'après défaillance. Il est implanté dans un programme de calcul aux éléments finis. À l'aide des essais laboratoire et des mésures in situ, le modéle a été validé. Les résultats des essais et des mesures concordent qualitatifs et quantitatifs aux résultats des calculations.

Jan 1, 2003

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 483 to 496 for the year ended 30 June 2004. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2004 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 30 July 2004 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2004 set out on pages 483 to 496 were approved by the Council on 30 July 2004 and are signed on its behalf by:

Jan 1, 2004

By A. More, J. Bullón

Metal casting is one of the most important operations in ferroalloys factories. After the tapping of the furnace and the depuration of the metal, the preparation for customers with cooling, crushing and sizing begins. In total production costs, this contains around 8 % of the total cost of the metal, depending on the value of the fines and other important parameters. From an investment point of view, this represents around 20% of the total capital for a new furnace. Casting onto a water-refrigerated copper plate is not new for molten metals. In steel, continuous casting machines are normal in every factory. Water granulation casting exists at some ferroalloys plants. However, the majority of plants and production technology still use the technology of lumping, crushing and sizing. This technology is time consuming, produces fines and requires a relatively large work force. In 2001, Ferroatlantica put into operation a new water-cooled copper casting-machine, which seems to be a very convenient solution to solve all these problems. It is in operation at a silicon factory; the same place where the new ELSA electrode was developed for silicon metal production. This paper describes our experiences using it.

Jan 1, 2004

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004