Search Documents

By S. Z. Pethö, H. Yilmaz

South Deep Mine is currently undertaking numerous voidfilling projects using low strength aerated cement products. Representative samples from one such site, were taken and tested for the load deformation behaviour under uniaxial loading conditions. The process of sample collection, laboratory preparation and testing are explained in detail. The results of testing were analyzed and the critical aspects pointed out as a design consideration to be implemented as part of the quality control and assurance program. Design aspects and underground application of the aerated cement product are discussed for the particular site on 58 level SV1. A simple instrumentation has been designed and installed to enable monitoring of any future movements in this area. A quality control and assurance process has been formulated enabling all aspects of the support installation in this excavation to be signed off.

Jan 1, 2003

By S. K. Murphy, S. M. Spottiswoode, A. M. Milev, D. Geyser

A portable, stand-alone instrument especially designed for recording strong ground motion was used in this study to create a large database of peak particle velocities measured underground. A total number of 39 sites located in stopes mining Carbon Leader and Ventersdorp Contact Reefs were investigated. Peak particle velocities whith values up to 3 m/s were recorded at some sites. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response. The maximum site response was obtained for source radii of between 5 m and 30 m and events locating within 200 m of the site. The extreme values of peak particle velocities were obtained in cases were the face-area lay within the source radius. Un instrument portable unique spécifiquement conçu pour enregistrer les mouvements dynamiques des terrains, a été utilisé dans cette étude pour créer une base de données importante sur la vélocité maximum des particules, mesurée en souterrain. Un nombre total de 39 sites situés dans les excavations exploitant les récifs appelés ‘Carbon Leader et Ventersdorp Contact Reefs’, a été investigué. Une vélocité maximale avec des valeurs allant jusqu’ à 3 m/s a été enregistrée sur certains sites. Les données enregistrées sur le bord de l’excavation ont été comparées aux données enregistrées par les réseaux séismiques de la mine pour déterminer la réponse du site. La réponse maximum du site a été obtenue pour des sources de rayons entre 5 m et 30 m et des évènements situés dans les 200 m du site. Les valeurs extrêmes de vélocités maximales ont été obtenues pour les cas où la zone de face se trouve à l’intérieur du rayon de la source. Ein mobiles, alleinstehendes Instrument, speziell entworfen um starke Formationsbewegungen aufzuzeichnen, wurde in dieser Studie verwendet um eine große Datenbank von Partikelspitzengeschwindigkeiten, die Untertage gemessen wurden, aufzuzeichnen. Eine Gesamtanzahl von 39 Aufstellungsorten in den Schichtabbauorten vom Carbon Leader und Ventersdorp Contact Reef wurden untersucht. Partikelspitzengeschwindigkeiten mit Werten bis zu 3 m/s wurden an einigen Standorten aufgezeichnet Die an der Oberfläche des Grubenraumes aufgezeichneten Daten wurden mit jenen Daten verglichen, die vom seismischen Netzwerk der Grube notiert wurden, um die örtliche Reaktion des Standortes zu bestimmen. Die maximale Standortreaktion wurde für Ursprungsradien von zwischen 5 m und 30 m erhalten und Ereignissen die sich innerhalb von 200 m vom Standort befanden. Die extremen Werte der Partikelhöchstgeschwindigkeiten wurdenin jenen Fällen erreicht wo sich der Abbaubereich innerhalb des Ursprungsradiuses befand.

Jan 1, 2003

By Henri Fredriksson, Rami Saario, Mark Weatherseed, Juri Matinheikki

"The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value. With regard to solvent extraction, the introduction of an innovative modular plant design will help to address these issues. The first such modular offering is Outotec’s VSF®X modular solvent-extraction plant that uses prefabricated and transportable modules. Reuse and recyclability have underpinned the design concept. The greatest advantage of the VSF®X modular solvent-extraction plant is its relocation possibility. Additionally, it is suitable for various metals and plant capacity is adjustable through a scalable modular structure. After a dedicated plant lifecycle, the plant can be dismantled and relocated to a new site. This reuse ability offers major benefits for short-term plants, making them more feasible due to higher residual value. A net present value analysis is made for two examples, a conventional plant with no relocation possibility and a modular movable plant with extended plant life cycle, in order to evaluate the feasibility of modular plants. Results indicate that modular plant design could offer an economical solution with the additional advantage of improved overall sustainability through its life cycle. INTRODUCTION The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value (NPV) (Mudd, 2010; Norgate & Jahanshahi, 2010) . Awareness of sustainability issues is also rising and sustainability reporting is now a key element of many companies’ public and investor relations. Major companies are now putting more effort in this area to earn legitimacy for new projects (Mudd 2010)."

Jan 1, 2015

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

By Sergio Burelli, Darren C. Megaw

"Operational challenges associated with solvent extraction (SX) plants include the effective on-line management of solids introduced from a variety of process streams. Solids are carried over from leaching circuits due to incomplete solid–liquid separation, may be formed as a result of chemical precipitation within the SX circuits, or introduced from downstream electrowinning operations. Solids in SX settlers result in operational challenges that impact plant availability and reduce optimized name-plate design capacity operation. Most available SX crud and bottom solids removal systems are limited in their effectiveness to handle high total suspended solids in SX circuits. Operations are often forced to take settlers off-line for complete removal of contained solids. These cleaning operations are hazardous, high risk, labour-intensive and costly in terms of production down-time and organic extractant and diluent reagent losses. Production pressure results in operations being reluctant to take SX settler units off-line for solids clean-out, resulting in continued operation of the SX, at reduced levels of mass transfer performance. Crud ForxTM is an SX solids removal system, for the on-line removal of interfacial and bottom solids associated with hydrometallurgical SX processes. A case study conducted at Glencore’s Mutanda Mining copper and cobalt operation in the Democratic Republic of Congo demonstrated the effectiveness of the Crud Forx. Benefits identified were an overall improvement in SX fire risk reduction, SX occupational health and safety and an improvement in copper mass transfer. INTRODUCTION Hydrometallurgical copper extraction and purification processes are often associated with ultra-fine solids distribution profiles throughout the process flowsheet (Virnig et al., 1999). The level and impact of the undesired deportment of solids to process streams varies from operation to operation, but the common denominator for all operations that employ solvent extraction (SX) as a copper upgrading and purification step is that, at some stage, they will have to manage solids (crud) within the SX circuit. Available crud removal systems in the industry have had limited success in continuous, effective interfacial crud and bottom solids removal from SX settlers. Most operations use basic removal methodologies which, at best, only result in delaying the requirement for taking the affected SX settler stages off-line for complete clean-out. This operational methodology results in production loss, increased SX organic extractant consumption and adds occupational health and safety risk to SX operations. The integrated Crud ForxTM/Crud FrogzTM SX solids management system assists operations in on-line SX solids management. The system has been proven to significantly reduce the requirement for off-line cleaning of settlers."

Jan 1, 2015

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By F. T. Cawood

This research report was produced in response to the release of the Mineral and Petroleum Royalty Bill. It involved are view of the mineral investment environments of selected countries in order to form an opinion on the appropriateness and competitiveness of the proposed royalty structure for South Africa. Many emerging countries have recently attracted a significant share of foreign investment, as a direct result of changes in policy. These are, by implication, the least risky and most favourable destinations for the ?investment dollar?. The five most competitive countries, namely Chile, Argentina, Peru, Mexico and Brazil have been identified as succeeding with their policy visions of creating favourable domestic investment environments. The investment rules of these countries served as a basis for the compilation of a Competitive Investment Framework (CIF). This is a template of best practice against which other investment environments, such as that of South Africa, can be measured. The framework indicates that mineral royalties should ideally be no more than three per cent, demonstrating that the regime proposed in the Royalty Bill is out of step with international best practice. Mineral royalties can never be viewed in isolation and in the assessment of the rates proposed in the Royalty Bill, one must consider the total taxation package. Such assessment appears in Section 5 of this report, demonstrating that there is reason for concern if National Treasury were to impose the rates stipulated in the Royalty Bill. The alternatives, conclusion and recommendations of the review appear in Sections 9 and 10. These are the result of independent analysis and assessment of the fundamental principles. It is done through the application of a Competitive Investment Framework that avoids the highly subjective and emotional views that often accompany a process like this.

Jan 1, 2003

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

By Ernie Holden, Chris Ringas

In the last 20 years, In Line Inspection (ILI) using intelligent pigs has become the principal tool used by pipeline operators to assess the condition of their pipelines. New pipelines are normally designed to take intelligent pigs, but many older pipelines require some modifications and special procedures for their inspection. This paper is aimed at practicing engineers and managers of pipelines, or people aspiring to those positions. The paper describes the benefits of ILI and some of the practical issues regarding pipeline preparation and cleaning, choice of inspection tool, running pigs in pipelines, and what to do with the data collected. What are the responsibilities of the Pipeline Engineer ? ? Maintain reliable and acceptable performance of the pipeline in terms of safety and product delivery at economical cost. ? Provide a defined margin of safety for operating the pipeline at its designated pressure. ? Provide timely information on all pipeline defects such that repairs can be carried out according to a managed schedule. What Defects does the Pipeline Operator have to cope with ? A useful record of actual incidents seen in pipelines can be obtained from the web site of the US Office of Pipeline Safety (OPS) - http://ops.dot.gov/stats/stats.htm. US pipeline Operators are obliged by Law to report all pipeline incidents exceeding certain threshold criteria (e.g loss of life, escape of product, cost of incident etc). These OPS statistics show that corrosion and third party damage have remained consistently the prime causes of reportable incidents in the US, with similar experience elsewhere. There are several kinds of flaws and defects in pipelines that can lead to failure, the main families being :- ? Metal loss ? Cracks or crack-like defects ? Laminations and other mid-wall defects ? Geometric anomalies

Jan 1, 2006

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d'excavabilité sont souvent en grande partie ignorés. Tandis que le choix d'une méthode de percement économique est évidemment une priorité claire dans l'étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

By Nicholas Adrian Barcza

"What affects and influences one’s perspective of the mining and metallurgical industries?One’s perspective of the industry we work in changes over time as a function of our experience as well as from the interaction we have with colleagues locally and probably even more so with those internationally. Furthermore, the ever-changing environment continues to impact the context in which one sees things. Living mostly in South Africa through its changes in the past fi fty years but also having the opportunity to travel extensively and work on projects abroad adds an invaluable richness to this more global perspective. One of the greatest challenges is how best to use this experience to endeavour to support the many potential opportunities in southern as well as sub-Saharan Africa. However, one has also to face the realities of how the best interests of the country and its peoples are sadly often not well served for various unfortunate reasons. Investment, education, regional stability, and good governance are some of the most critical considerations for the prosperity and survival of the region.The mining and metallurgical industry in southern and sub-Saharan Africa changed significantly during the post-colonial and apartheid eras as a result of global and regional developments that have impacted the ownership of businesses, the technologies used, and products produced in a manner that was not envisaged even fi fty years ago. Southern Africa’s mining and metallurgical industry has progressed from one based mostly on diamonds and gold in the late 19th century to a much more diverse one that involves the production of a variety of other precious, base, and ferrous metals and minerals as well as coal and industrial minerals. The infrastructure and manufacturing capacity was largely developed to meet the needs of this industry during its growth phases, but even though the dynamics have changed there is still a need for more efficient and effective support systems in the region."

Jul 1, 2019

By Gaspard Devos

1. A NEW CONTEXT FOR METAL INDUSTRY Producers and owners of industrial extractive sites are living hard times due to Environmental pressure and liabilities. This is valid whatever the region in the world, it is just a question of time. On one hand, the normative environmental pressure is increasing through more severe regulations and controls on all pollution sources and production materials. [ ] Furthermore, more impurities are extracted and captured, more the volume of the related wastes is increasing. But disposal costs are increasing, disposal areas for wastes are restricted, markets for wastes are limited and technologies for waste treatment are, most of the time, not available. On the other hand, for most of the extractive industries, the costs required to get access to refine primary raw material are killing the profitability of the industry. Definitively, a technological and economical breakthrough is ongoing: extractive industries have to increase their feed from secondary material and to be involved more and more with the recycling business.

Jan 1, 2005

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By W. H. Van Niekerk

The metal zinc has been around since only about 1400 AD. This may sound like a long time, but when compared to fellow base metals copper and lead, which were discovered in 5000 and 4000 BC respectively, it is evident that zinc is a fairly new kid on the block. This may also be the reason why many new facts and benefits of zinc are still being discovered. For instance, it has been discovered only in the last few decades that virtually no life on earth is possible without zinc. In this address it will be shown that zinc is not only very useful to mankind, but is in fact vitally important for all forms of life. It will be shown that zinc is natural, zinc is essential for life, zinc protects, zinc contributes to the well-being of society and that zinc is fully recyclable. It is therefore hoped, that by the end of this address, zinc will no longer be viewed only as the metal that is responsible for the nice colour of roofing sheets and steel buckets, but may indeed be man?s best friend.

Jan 1, 2005