Search Documents

By A. J. Feltenstein

A theoretical model for prediction of dissolved gold loss from a rotary vacuum filter was developed as part of a program to implement optimizing control on gold plants The filter was modelled using a modification of the Hagen-Poiseuille equation and the Choudhury and Dahlstrom washing equation. The model has three parameters which must be determined from accumulated data before predictions can be made. These are the cake and cloth resistances and the filter washing efficiency. The model predicts with a fair degree of accuracy the response of the filter to changes in the independent variables and will therefore be a useful tool in the plant optimization study.

Jan 1, 1987

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

By S. Shamaila

The design and efficient operation of density-based mineral processing units requires regular densimetric analysis to be carried out on the various associated process streams. The results obtained from such analyses can have wide application, including the generation of washability and partition curves, which are critical for process design, control, and simulation. This paper describes some of the collaborative efforts that Kumba Iron Ore, in partnership with Springer New Technology and Anglo Technical Solutions Research, is pursuing in developing a novel density determination technique exploiting X-ray transmission (XRT) and optical imaging. This technique is being developed with the aim to determine sample density distributions that apply to washability characterisation of ores. This technique is aimed to be an alternative to the traditional sink and float method. For certain applications sink and float has required the use of tetrabromoethane (TBE) solution?a chemical that has been classified as harmful and environmentally unfriendly. This paper therefore presents some achievements in developing this novel technique which seems to be very promising.

Jan 1, 2012

By T. De Lange

Extensions to the beneficiation plant at the Grootegeluk Coal Mine are currently being planned in order to provide power station coal for Escom's Matimba Power Station, presently under construction. A simulation model was developed on the Olivetti M-24 microcomputer to facilitate the development of the envisaged flowsheet. The computer program simulates the heavy-medium separation and screening unit operations. The model is based on the construction of the Tromp partition curve described by an arctangent function, allowing ideal and non-ideal separations. The paper discusses the determination of the parameters required by the arctangent curve from standard process parameters such as Epm, Wolf cut-point, Tromp cutpoint and screening efficiency. The accuracy and shortcomings of the model are discussed, while an overview of the application of the model to evaluate borehole and bulk sample analyses is also given. It is concluded that the model is an invaluable aid to general flowsheet development.

Jan 1, 1987

By T. Marsden

The demand for continuous improvement in the industrial world is an ongoing process. Some sectors, where the competitive forces are well established, have led the development of new and reliable technological innovations. Although the metallurgical industry can rightfully be proud of its process improvements, there is still work to be done in materials and in material handling. In some cases, the improvements will be as simple as adopting technologies that have been perfected in other processing or manufacturing industries. This paper discusses the next design generation for copper tankhouses which will yield: ?Improved copper quality ?Improved equipment availability ?Lower life cycle costs ?Safer operations. These benefits will be realized through new developments and design improvements in: ?Permanent cathodes ?Cathode washing ?Cathode stripping machines ?Anode preparation machines ?Improved lead anode design ?Recycling of lead anodes and refurbishment of cathodes. The demand for base metals, and in particular copper, has led to more research into improving efficiencies in electrowinning and refinery plants around the world. One of the areas previously taken as a matter of course was the production of lead anodes and stainless steel cathodes. In South America alone there are over 600 000 cathodes and anodes in circulation?a very significant figure.

Jan 1, 2009

By R. V. Ramani

Managers need quality information for effective decision making. This demand, at the present time, is being fulfilled by the increased use of computers via information systems, decision support systems and management information systems. The idea of incorporating intelligence into computers to aid decision-makers has been evolving for over two decades. In recent years, significant progress is reported on applications to business and sciences. In engineering functions, the Artificial Intelligence approach that seems to have great potential is the application of Knowledge Based Systems. The primary objective of this paper is to identify domains in mining engineering where application of knowledge based systems could be beneficial. In- corporation of the expertise required during the analysis and interpretation stages of an engineering design problem through knowledge based systems is recognized as an area of significant benefit. To this end, the components of knowledge based systems for mine ventilation and strata control design are described. The potential applications and limitations of knowledge based systems are outlined.

Jan 1, 1987

By J. Manchisi

Laboratory investigations were conducted to establish the feasibility of bioleaching a mixed copper oxide/sulphide rougher concentrate from Nchanga Mine on the Zambian Copperbelt. The objective was to determine the kinetics and extent of copper extraction for this material. Batch experiments were conducted under different solution conditions in stirred tank bioreactors. The progress of (bio)leaching was monitored through measurements of soluble ferrous and ferric iron, copper, pH, and redox potentials, while bacterial activity was monitored online through 02 and C02 gas utilization rates. About 20 per cent copper was solubilized within 2 hours in all cases of non-oxidative (abiotic), oxidative (abiotic), and bioleaching experiments. This was attributed to the dissolution of mainly copper oxides. Subsequently, bioleaching experiments resulted in an overall copper extraction of 93 per cent, with up to 8 g.L-1 copper after six leaching days, compared to 58 per cent copper extraction in the abiotic oxidative acid leaching experiments. However, there was little effect of time (i.e. poor dissolution kinetics) on copper recovery for abiotic non-oxidative acid leaching of the material. Hence, the rate of sulphide leaching increased due to the activity of bacteria. Thus, the material is potentially bioleachable under mesophilic conditions. However, more exhaustive test work needs to be conducted to establish the effect of bioleaching variables and heat requirement.

Jan 1, 2012

By R. G. B. Pickering

The South African narrow reef hard rock mining industry has been stuck in a time warp with relatively little change in the mining process in the last century. This paper presents a methodology on how to implement change in narrow reef hard rock mining. It then explores a number of technologies that have been introduced into this mining industry and the impact that they have had on the mining process. The author then presents his view on whether the defined change process has been followed and sets out to identify the most critical aspect of ensuring that change is successfully implemented. Future demand will also be speculated on.

Jan 1, 2007

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s and is recognized a shaving significant potential for optimizing production scheduling problems for both surface and underground mining. The major problem in long-term production scheduling for underground orebodies generally relate to the large number of variables needed to formulate a MIP model, which makes it too complex to solve. As the number of variables in the model increase, solution times are known to increase at an exponential rate. In many instances the more extensive use of MIP models has been limited due to excessive solution times.

Jan 1, 2010

By G. R. Addie

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains a new method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007

By B. B. Tati

The project report is based on vacation work done by the writer at the Khutala Colliery during December/January 2009?2010. The purpose of this report is to explain and describe the design process in a multi-seam mine design for coal extraction at the Khutala Colliery. The multi-seam design will focus on the No. 2 and No. 4 seams as these are the seams that are currently being mined by underground methods at Khutala Colliery. The seam thicknesses and the parting thickness between the seams provide suitable conditions for designing a multi-seam mine design. An investigation into the pillar design aspects is carried out followed by a numerical modelling analysis of various scenarios. This analysis validates the first principles approach provided by multi-seam design guidelines. The design results from the analysis of the selected pillar design indicate sufficient parting for primitive conditions between seams, thus illuminating the need for superimposing in-panel pillars. This multi-seam mine design confirms the potential for the extraction of coal in a new panel. The design indicates that significant amounts of power station coal are present and suitable for extraction by room and pillar mining methods. The panel block indicates 401 625 tonnes of ROM coal. This block has a life of panel that will be mined just over a 4-month period. This 4-month period is assumed to mined at a production rate of 48 000 tonnes per month. The total capital cost required for the new panel is R48 281 127.05. Keywords Multi-seam mining, panel design, ventilation flow, superimposition.

Jan 1, 2011

By C. Rodrigues

This investigation compares the gas adsorption behaviour and capacity of three bituminous coals from South Africa, of similar rank, by assessing the characteristics of the raw coal, as well as the resulting float and sink fractions (at 1.80 cm3/g) obtained by density separation of crushed coal samples. Calculations were also made to obtain the raw coal gas storage capacity from the weighted contribution of both float and sink fractions results, thereby permitting comparison with the analysed results of the raw coal. The study demonstrated that the clean fraction of a coal has the highest capacity to retain gas in the sorbed state, followed by raw coal, and lastly the sink fraction, and re?confirmed previous investigations that showed minerals to be inhibitors of gas adsorption and retention.

Jan 1, 2008

By M. W. John, I. D. Matthews

SYNOPSIS This paper describes the process adopted for the recovery of gold from a dump originating from clean-up operations at Durban Roodepoort Deep Gold Mine. The gold-bearing dump material was refractory in nature, not being amenable to cyanidation because of the high level of carbonaceous material present. The laboratory tests on the material involved particle-size and chemical analyses, a mineralogical examination of the material, preliminary tests, and optimization of the process for the treatment of the dump material. The preliminary tests included tests on roasting, flotation, pre-leaching, adsorbent-in-leach, and blinding. Of these options, carbon-in-leach showed the greatest potential. The rate of gold dissolution, the rate of gold adsorption by the carbonaceous material, and the ratio of carbon to pulp were then investigated. It was determined that the ratio of carbon to pulp necessary to yield a reasonable gold recovery resulted in a carbon loading that was not high enough for economic elution and regeneration. A process incorporating washing of the carbon with cold acid between adsorption cycles was tested, and reasonable gold recoveries and carbon loadings were obtained. Durban Roodepoort Deep Gold Mine piloted the conceptualized process and determined that it was economically feasible. Two Browns tanks on site were modified, and an acid-wash tank was installed. The capital outlay for the plant was recovered within some 3 months.

Jan 1, 1990

By D. F. Sinclair

It is often said in business that if you don't have a customer you don't have a business. The same rule applies to project evaluation; if you don't have customers you really don't have a viable project. It is therefore essential that in the early stages of project evaluation the following fundamental questions are addressed: ? What products will this project produce? ? Who are the potential customers? ? What are the customers' requirements with respect to grade and impurities? ? Do they have adequate capacity to take the production from the proposed project? ? Will the products introduce adverse effects in the customer's process circuits? ? Will additional waste streams requiring disposal be produced? In the past the attitude has been along the lines of the customer will take whatever we produce at the mine site. Times have now changed with customers now operating under much tighter environmental regulation with waste disposal becoming increasingly difficult. It would therefore be prudent that the principles of product stewardship be used as a tool in project evaluation. This paper will provide a general discussion on customer requirements and provide detail on case studies of the impact of mine products on smelter process circuits. It will provide examples where there were synergies between the mine product and the smelter circuit and where the mine product had adverse impacts on smelter performance.

Jan 1, 2007

By S. Poirier, J. -M. Facteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET’s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialized in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET’s programme in mechanization and automation for narrow-vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies(Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow-vein mining industry. Several important impacts of this project will be monitored. In particular, a database of methods and equipment used in narrow-vein mining is being developed. A key thrust is to identify operators’ needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The paper will present the objectives of the narrow-vein mining project and some of the results, including the web site developed to present the results of the project.

Sep 1, 2001

By W. F. Nothard, J. R. C. Hill

The Rhodesian approach to the vegetating of slimes dams by J. R. C. HILL, B.Sc.(Agric.) (Visitor) and W. F. NOTHARD (Visitor) To prevent environmental pollution from mine dumps, it is necessary to stabilize them either mechanically or biologically. In the long term biological stabilization is more attractive because of its permanent nature. Initially, the basis of stabilization is in the correct siting and construction of the dump. The main toxic factors influencing plant growth on Rhodesian mine dumps are arsenic, antimony, copper, nickel, a high ratio of magnesium to calcium, excessive soluble salts, high pH, and Iow macronutrient content. Root-growth studies in culture solution and pot experiments are used to supplement information on the suitability of plant material obtained from replicated field trials on mine dumps. In addition to the selection of plants for toxic tolerance, it is advisable to provide multiple-layer protection with trees, shrubs, and grasses. Further, a range of different plant species gives greater biological stability. Protection must be provided for young plants against wind erosion and the abrasive effects of windblown sand. Planted wind breaks are preferred to mechanical forms; windrows of garden refuse make good wind breaks and at the same time introduce organic material to the dump and provide a good environment for seedling establishment. The use of artificial fertilizers and sewage effluent is recommended to hasten the development of a complete and protective plant cover.

Jan 12, 1973

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By L. I. Boshoff, S. Gracie

This paper discusses pilot and laboratory-scale metallurgical test work conducted on bulk samples from a low grade heavy mineral deposit and provides an overview of basic practical metallurgical techniques applied to ascertain the suitability of existing production plants to process material from this orebody. Previous investigations have shown this specific orebody to be more challenging in terms of mineral beneficiation as it has a high gangue mineral content. Test work was conducted on targeted stratigraphic units based on lithology and assay results to enable identification of the stratigraphic units portraying quality issues. Unit specific metallurgical pilot work has never been conducted on any of the RBM orebodies and is a new field currently being explored. During this investigation focus was placed on potential quality and yield issues for ilmenite product, with particular reference to CaO quality. A basic evaluation of zircon and rutile separability was also conducted. The test work was conducted using a comparative baseline methodology with metallurgical test work methods specifically aiming at mimicking the existing production plant as closely as possible. This enabled not only the likely metallurgical performance to be assessed but also indicated whether current plant design would be suitable to process the low grade ore types into products of acceptable quality at acceptable yields. The methods and findings discussed in this paper indicate that although there is considerable variation between different units, a blended feed can be successfully processed. With unit specific metallurgical data applied to the existing geological block model, expected yields and recoveries using current plant designs could be predicted.

Jan 1, 2007

By D. Vogt

"Rock has been cut in the process of mining since before the invention of explosives. Today, we seek to return to cutting to reap the benefits of continuous operations for South African underground hard-rock mines, to improve speed of access to the orebody, and to improve the efficiency of mining operations.Development of new technology fits within a framework of engineering knowledge. By understanding the characteristics of the rock, the tools we use to cut it with, and the history of mining and rock cutting, we can see the genesis of the road-header, the longwall, and the continuous miner, all drag bit cutters. They have emerged as the solutions of choice for underground mining of softer materials such as coal and potash. In hard rock, the challenges are the forces required to break the rock, and the wear of the tools caused by the rock’s abrasiveness. Only disc cutters currently handle the challenges, and even then, often not economically. New materials like thermally stable diamond composite will help, as will combinations of mechanical cutters and other methods such as high-pressure water or high temperatures.It is not clear what will emerge as the consensus technique for hardrock cutting. Experience teaches that development is expensive and the market is small. Will mining companies partner with equipment developers to make the technological leap? Or will the solution come from a systems approach, not considered here?IntroductionBlasting is the dominant method of breaking rock for the purposes of mining. When used underground, blasting is part of a batch process. If rock can be cut rather than blasted, mining can become continuous, leading to process and efficiency improvements.Coal produced from underground mines is now predominantly excavated using mechanical means, but underground hard rock is still broken primarily by explosives.This paper traces the history of rock cutting, reviews the main physical processes that are or could be used, and comments on the future. It is written from the perspective of narrow-stope hard-rock mining typical of South African gold and platinum mines."

Jan 1, 2016