Search Documents

By Robert A. Bradburn

The Bureau of Mines has developed a miniature, portable two-level oxygen-deficiency alarm and produced three prototype models. Each operates from a 4.2-v dc power source, and the highest current drain of any model is 80 ma. An electrochemical cell, which produces an electrical output in proportion to the partial pressure of oxygen to which it is exposed, is used as an oxygen detector. The output of the cell is applied to an electronic circuit that detects two different levels of oxygen percentage below that of normal air, and produces distinct audible signals at these levels. The hazard alarm mode is activated when the oxygen percentage first drops below normal and produces a 500-cps "beep" tone with an intermittency of 1 cps. The danger mode produces a continuous 500-cps audible signal when the oxygen percentage drops still lower.

Jan 1, 1968

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By J. S. Miller

The Bureau of Mines conducted surface tests to determine the feasibility of using liquid explosives for underground rock fracturing. The effects of configuration, confinement, length, critical layer thickness, and fracture-propping sand on detonation and explosive propagation velocity of desensitized nitroglycerin were studied, using polymethyl methacrylate and glass-plate reservoirs through lengths from 3 to 12 ft, with explosive-layer thicknesses from 0.1875 to 0.0312 in and in aluminum tubes 8 ft long with diameters from 2.000 to 0.125 in. Interval and continuous detonation velocity data were obtained. Under the test conditions detonation velocity was dependent upon explosive confinement and fracture-propping sand. The detonation velocity of a confined nitroglycerin explosion in aluminum tubes can be reduced by as much as 85 percent, when the tube contains fracture-propping sand. The shape of the reservoir, whether triangular or rectangular, has little effect on the detonation velocity or explosive propagation. The critical or minimum explosive-layer thickness between glass plates, capable of supporting propagation, was 0.0312 in. The presence of a fracture-propping sand in the sheetlike layers increased the critical explosive layer thickness to 0.0625 in. In nitroglycerin-filled and nitroglycerin-sand filled tubes, the minimum tube diameters successfully tested were 0.125 in and 0.375 in, respectively.

Jan 1, 1969

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By Thomas J. Albin

U.S. Bureau of Mines research has found that maintenance of surface mining equipment is involved in slightly more than one-third (34.1 pct) of all surface mining accidents. Two groups of machines, haulage trucks and power shovels, accounted for over one-half of all surface mining mobile equipment maintenance accidents in 1978-84. Maintenance work-time histories for these machines were compared with accident records to identify the most hazardous-to-maintain systems within the machines. Recommendations to reduce the accident risk associated with maintenance of these hazardous systems are presented.

Jan 1, 1990

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993

By Thomas V. Falkie

The purpose of this work was to investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors -- geometrical, geological, mechanical, or procedural which affect the delivery rate, and to develop quantitative rate descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily influences the loading function. The geometrical factors -- the dimensions of the work area in relation to the dimensions of the mining machine - were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent independent variables. It is expected that this work will be useful in operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Jan 1, 1972

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area's northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By W. G. Payne, A. C. Richardson, B. L. Gandrud

"INTRODUCTION The Connellsville mine of the Yolande Coal & Coke Co. is in the southwestern part of Jefferson County, Ala., about 30 miles southwest of Birmingham. The mine is on the Blue Creek bed, which is about 6 feet thick and dips at a angle of 18º. The bed is worked by the room-and-pillar method and is mined by both machine and hand methods. The Blue Creek bed at this point yields a high ash, low-volatile coal with excellent coking properties. Because of its exceptionally low volatile content and high coking strength, this coal is excellent for blending with Alabama coals of higher volatile content and weaker coking properties to form blends suitable for production of metallurgical coke.A sample of washed coal taken during this investigation gave the following analysis on an as received"" basis: Moisture, 8.3 per cent; volatile matter-, 20.2 per cent; ash, 8.0 per cent; fixed carbon, 63.5 per cent. The high ash content of this coal limits the quantity which can be utilized when low-ash coke is required. In the Birmingham district it is usually difficult to sell as coking coal a product that contains more than 8.0 per cent ash. To produce a. coal with this ash content at Connellsville presents a somewhat difficult washing problem. This paper gives the results of an investigation that was conducted by the Southern Experiment Station of the U. S. Bureau of Mines in cooperation with the University of Alabama and the Yolane Coal & Coke Co. for the purpose of determining the washing characteristics of the coal and the possibility of reducing its ash content on coal-washing tables.The practice at the Connellsville washery at the time of beginning this investigation was to crush the run-of-mine coal to pass a 1 1/2-inch round-hole screen and to treat the satire output on two primary, 3-compartment jigs. A. middling product was recovered from the primary jigs which was re-treated on a single-compartment rougher jig. This system yields a product of acceptable ash content, but the yield is low and the loss of good coal in the refuse is high."

Feb 1, 1933

By John H. Johnson

A study of mine air quality was conducted using the latest advanced continuous monitoring instruments. An overview of the various interacting variables in the mine that affect air quality is presented. One effort involves the evaluation of portable instruments, the development of measurement techniques, sample analysis procedures and computer programs for statistical analysis of measurement data, and the application of the instruments and techniques to the measurement of the concentrations of CO, CO2, NO, NO2 and particulate matter in a lead and a copper underground mine. A second effort involves the first application of the Mine Air Monitoring Laboratory (MAML), a mobile trailer containing laboratory type instruments, sampling and data systems for the measurement of CO, CO2, NO, NO2 and particulate matter. The data from the MAML for blasting and for operating diesel equipment are analyzed and presented in various plots.

Jan 1, 1977

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933