Search Documents

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material's elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure., but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo,, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of intolerability which -accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a nonodorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By Robert M. Becker

A multistage probability model for assessing the reliability of mineral samples following any number of stages of sample reduction is presented. Sample reduction is the process of alternately crushing or grinding and sampling mineral particles prior to assaying. The final multistage model developed accurately describes the ideal sample reduction practice. This model is based on previously developed and experimentally tested models for a single stage of sampling. The problem is approached through the probability distributions for the various stages of sampling. The probability distribution, moments, and moment relationships for a single stage of sampling are first reviewed, and the useful concept of unit moments is defined. In presenting the models for two stages of sampling, emphasis is placed on the physical description of the sample reduction process which leads quite naturally to its mathematical representation. In this representation, crushing or particle-size reduction between the stages of sampling is viewed as a random process with respect to the number and proportion of particles of the various kinds produced. The physical and mathematical description is extended to more than two stages of sample reduction, and the first three moments for any number of stages are developed. In common sample reduction practice the effects of a finite population (finite amount of material) at each stage of sampling appear to be important in describing the variance contribution of each stage. This is also true for the third moment about the mean. An example is cited in which the skewness increases by more than an order of magnitude when several stages of sampling are considered. This is largely due to the dependence of the multistage third moment about the mean on the variance. In general the model and results should be useful in helping to understand, control, and reduce the random errors that arise in the sample reduction process.

Jan 1, 1968

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By Walter E. Pittman

This Bureau of Mines study surveys the current state of technology and the various research efforts that have been undertaken to dewater the dilute phosphatic clays generated in the production of phosphate rock. The research described includes early dewatering experiments, fundamental studies of clays and of flocculation, and minor dewatering techniques such as freeze-thaw methods, the ANDCO process, moving screens, sand wick, crust development, and overburden pumping. Some methods that are currently being evaluated are described. They include the Estech sand-clay mix process using the Enviro-Clear thickener, sand-clay sandwiching, dredge mix, dredge process, and the sand-spray process. Developing technology for dewatering phosphatic clays also is described, including the Bureau of Mines rotary trommel method and the Gardinier process.

Jan 1, 1984

By Jan M. Mutmansky, Christopher J. Rise

"One of the most serious long term health problems associated with underground,mining is Coal Workers Pneumoconiosis (CWI'), more commonly known as Black Lung Disease. It occurs in some coal workers, normally after 15 or more years of exposure to coal mine dust, and leads to a variety of respiratory problems. Two types of pneumoconiosis are recognized simple CWP, which has been estimated to affect 6.9 percent of miners and is a condition that does not impair the miner's ability to work nor reduce life expectancy; and a more severe form of black lung (called progressive massive fibrosis) that occurs in about one percent of the cases and results in severe lung damage.Although the relationship between coal dust and CWP has long been recognized, detailed knowledge of the relationship is insufficient for setting up authoritative guidelines to reduce the health risks for those employed in dusty,underground environments. CWP is not only a health problem for workers that causes considerable distress, it is also a very expensive problem the total annual costs associated with CWP approach two billion dollars.As part of its efforts to combat CWP, the U.S. Bureau of Mines in 1983 established a Generic Mineral Technology Center to carry out basic research into all aspects of respirable coal dust:— control of dust generation — the behavior of dust in the mine — characterization of dust particles interaction of dust and lung— the relationships among dust generation and mobility and the mine environment, geology, and seam characteristics,Penn State, West Virginia University, the University of Minnesota, and the Massachusetts Institute of Technology are involved in this research, which is administered from the Department of Mineral Engineering at Penn State.Our work is one of the seven projects to be conducted at Penn Slate. We are concerned particularly with the characterization of dust and its relationships with the mine environment, and our main goal is to establish standard procedures for describing and measuring these variables.Coal DustCoal dust is a very complex material that varies greatly in chemical and mineralogical properties. Moreover, it is not the only constituent of respirable dust in the mine. When a coal seam is mined, it is inevitable that rock particles other than coal are included in the material. This rock comes from the mine roof, the floor, and the partings and inclusions within the coal scams. Since the roof and floor strata, the partings and inclusions are often stronger than the coal, mining them frequently causes more dust than mining the coal itself. One of the objectives of our research is to find the relationships between a specific coal's characteristics before it is mined and the respirable dust characteristics after it is mined. We are particularly interested in the size distribution of particles, the chemical properties, and the mineralogical properties."

Jun 1, 1988

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By John P. Powell, J. L. Eakin

"INTRODUCTION AND SUMMARYNowata County, in the northeast corner of Oklahoma, is one of the principal oil-producing counties of this stripper area. Many fields in the county were opened and much oil was produced before statehood. The location of the major fields, as defined by the Oklahoma Corporation Commission, 2/ the outline of the areas of water-flooding activity, and the location of the several projects described in detail in this report are shown in figure 1.There was some drilling in the county earlier; but it was not until after 1904, when the Secretary of the Interior confirmed as valid the leases granted by the Cherokee Nation, that the major drilling activity began. Initial development in this part of Oklahoma was in the Chelsea field in Rogers County, which adjoins Novata County on the south. The activity spread rapidly northward to the Alluwe and Coody's Bluff fields, and then to the Nowata-Claggett field. Continued exploration resulted in discovery of the Delaware-Childers field, where some wells having an initial production of 1,000 barrels daily were completed. Fields discovered and developed during the next few years included the Lenepah (Elliott), Adair, California Creek, Curl Creek, Woody, and South Coffeyville. The oil-production history of Nowata County is shown in figure 2. In assembling the data for a production curve, it was found that the combined production records for Nowata and Rogers Counties were available for 1914 to 1951, inclusive, and that records for the individual counties were available only from 1926 to 1951, inclusive. The early production figures for the counties from 1905 to 1914, inclusive, except for 1909, were calculated from the initial production statistics of the Federal Geological Survey mineral resources bulletins and production data assembled by C. H. Beal. 3/ The production values for 1905 to 1926 for Nowata County were obtained by dividing the total production for the two counties by a percentage factor derived from known facts regarding the oil industry in the area. Production figures for the individual counties from 1926 to 1933, inclusive, were obtained from the files of the Oil and Gas Journal, and the figures from 1933 through 1951 were obtained from monthly reports of the Oklahoma Corporation Commission."

Jun 1, 1952

By S. J. Davenport

[The tremendous increase in mine mechanization since 1929 has increased markedly the application of electric power in and about the coal mines of the United States. Cutting, drilling, and leading machines have replaced hand-mining methods in nary mines. As a result, expansion of the gathering haulage has necessitated introduction of extensive feeder, trolley, grid other power wires. (1)3/ In spite of this vast mechanization the fatality rate from electric shock has been on the decline. However, there are still too many accidents, and efforts to eliminate electrical hazards cannot be relaxed. It is hoped that an acquaintance with the physiological aspects of electrical accidents will make workers end management aware of the lurking dangers of this very common and extremely dangerous form of energy.]

Jan 1, 1951

By Ivette E. Torres

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other sections of 1992 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible to complete, without the efforts of the personnel of our counterpart national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, our appreciation is expressed to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1994

Although the Stamler feeder/breaker has been used for coal crushing in underground mines for many years, it has only recently been applied to other crushing operations. Two companies presently using Stamler feeder/breakers for rock crushing were contacted regarding their experiences with the units in actual field use. In both cases information was obtained directly from the individuals responsible for field operation and maintenance of the units. White Pine Copper Co. has been using Stamler feeder/breakers for over two years to crush copper ore. They now have fourteen 450-ton-per-hour units on line. The ore has a compressive strength of from 18,000 to 28,000 psi and is extremely abrasive. Maintenance is performed on a tonnage basis. The breaker shaft is replaced every 250,000 tons (requiring about 4 hrs) and picks are replaced about every 1500 tons by the operator (requiring about 2 min per pick). Very little unscheduled maintenance has been required. Crushing costs are fairly high (estimated at 13 to 15t per ton including maintenance and operation) because of tale extreme abrasiveness of the material. A new Stamler feeder/breaker with Ultramet wear surfaces was put or line in June 1976. Ultramet was found to increase the life of belt transfer station surfaces by up to 400 percent and it is hoped that it will do the same for the feeder/breaker. At this time it is still too early to evaluate the performance of the Ultramet unit. If it does improve abrasion resistance, crushing costs could be greatly reduced. White Pine is very pleased with the units and the service provided by Stamler.

Jan 1, 1976

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

By Samuel W. McNary

In August 1984 the U.S. Bureau of Mines conducted a study of the mineral resource development potential of the Badger Canyon-Antelope Creek area, within the Boulder-Pioneer wilderness study area, about 5 miles northeast of Ketchum, 10. The purpose of this study was to investigate in greater detail an area which was designated by the U.S. Geological Survey (USGS) and the Bureau as having a moderate mineral resource potential for zinc, molybdenum, lead, and silver, and a low potential for copper. One hundred twenty-eight soil samples were taken along a 6,2S0-ft traverse on the ridge separating Badger Canyon and Antelope Creek. 5 Five rock samples were collected from old prospect pits and mineralized outcrops. All samples were analyzed for gold. Silver, copper, lead, zinc, molybdenum, arsenic, antimony, vanadium, and mercury. The metal concentrations in the soil samples along the traverse are irregularly distributed. Samples collected near old prospect pits tend to be high in lead and zinc, undoubtedly a reflection of underlying galena-and sphalerite-bearing quartz veins. All of the copper and mercury values in the soils are less than the detection limit, as are most of the lead, molybdenum, and antimony values. Except for lead and zinc values, the metal concentrations in the rock samples are low. Galena and sphalerite were observed in quartz vein samples collected at the old prospects. The results of the study indicate that the galena-sphalerite-bearing quartz veins and veinlets are too narrow, widely-spaced, and low in metal values to be economic. Low concentrations of metals in the soil and rock samples, combined with the lack of major mining activity in the past, indicate that the area has a low likelihood for economic development.

Jan 1, 1986

By Aner W. Erickson

"Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.A preliminary examination was made by S. P. Holt, mining engineer of the Bureau of Mines, in company with John Reed, L. A. Warner, and W. S. Twenhofel of the Federal Geological Survey, on July 14, l943. Three samples were taken, rough estimates were made, and it was proposed that the area be mapped, topographically and geologically,. Dip-needle work was added to the program, and it was decided that, should results warrant, the deposits would be diamond-drilled.From March 26 to May 28, 1944, the deposits were examined thoroughly by Bureau of Mines personnel under the direction of the author. Thirty-two acres were mapped with contour intervals of 10 feet, grids were established covering the principal outcrops, over 1,500 dip-needle readings were secured, and the magnetite bodies were outlined. Additional information was gathered by trench inch and channel-sampling, 600 linear feet of trench being dug and 32 channel samples being cut. Finally, the mapped area was checked for nonoutcropping deposits by taking dip-needle readings at 10-foot intervals along the traverse lines, creeks, trails, and all outstanding topographical features. This re-connaissance work gave sufficient coverage of the 32 acres to eliminate the possibility of further magnetite bodies of any consequence remaining undiscovered.Acknowledgment is made to Nile Johannsen, assayer, Territorial Department of Mines, Ketchfkan, Alaska, for determination of samples.The deposits are on Prince of Wales Island in Southeastern Alaska near Tolstoi Pay, a deep-water indentation at the northwest and of Kasdan Peninsula. The physical features are shown on figures 1 and 2 and the location of the deposition figure 3. Old workings were found on the west side of Tolstoi Mountain; between elevations of 650 and 1,150 feet, at distances of 3/4 to 1-1/4 miles from the east shore of Tolstoi Bay.Access to the area is over a brushed foot trail built by the Bureau of Mines. Topography would permit construction of either surface or aerial tramways at moderate cost but would make road building expensive. Deep-water navigation, permitting inexpensive water transportation, is possible the year around.Kasaan Peninsula is an area of moderate relief, being considerably less rugged than the mainland to the east. Most of the mountains and ridges are less than 2,500 feet in height and show evidence of having been covered by the ice cap of the Pleistocene age. Rock exposures below elevations of 2,000 feet are limited, as extensive overburden 2 to 20 feet deep covers the greater part of the peninsula."

Dec 1, 1948

The Mine Safety and Health Administration (MSHA) defines an independent contractor as "any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine." Contractors that perform specific types of work are required to report the number of employees who perform work at coal mines and at noncoal mines.

Jan 1, 2004