Search Documents

By Fred N. Kissell

Methane flows and pressures were measured in mines in the Pittsburgh, Hartshorne, and Pocahontas No. 3 coalbeds. From the data, the permeability of each of these coal beds was computed. It was found to depend strongly on the type of coal and on the amount of water in the coalbed, and it was found to increase with time. All of the coalbeds had a high-permeability zone adjacent to the face or rib, and the Pittsburgh bed exhibited directional anisotropy. Surprisingly, little or no overburden effect was observed.

Jan 1, 1972

By John Nagy

The Bureau of Mines examined explosion development in a closed spherical vessel, mathematically correlating flame travel, pressure, and time with parameters defining the reaction. The model assumes that burnt and unburnt zones are separated by a thin, radially moving flame front. Isothermal and adiabatic systems are considered. Correlation with gas and dust explosion data is better for the adiabatic system, but the isothermal development is simpler and in reasonably good agreement. Interpretation of the explosion phenomena is facilitated by expressing the rate of mole change in the flame front in terms of elementary parameters. This expression is developed by examining the components of spatial-flame velocity.

Jan 1, 1969

To provide safer and more efficient mine operations by improving the operational performance of underground trolley line communication systems. Approach The dc trolley line provides a convenient means of In-mine communication since it can carry signals to each phone on the system whether the phones are in mine vehicles or in a fixed location such as that of a dispatcher. In many cases, however, the system does not perform satisfactorily. Short communication range, noise, and dead spots commonly interfere with effective communication. These problems are inherent with the trolley line, which was designed to transmit power and not communication Signals. As a power line, the trolley line is connected to rectifiers and feeds many loads such as motors, water pumps, track block lights, etc. Each of these devices represents a low impedance radio frequency (RF) shunt that seriously reduces carrier communication Signals. Performance is therefore often poor and can be improved only if the effects of the various shunts can be reduced. The Bureau of Mines has developed numerous methods applicable to either existing or planned phone systems which can improve communication range and reduce the shunting effects of the various loads.

Jan 1, 1983

Lower the respirable dust exposure of longwall shearer operators with improved water spray systems on the shearer. Approach Orient sprays (rather than relocate them) so that dust is held against the face. How It Works Research by the Bureau has indicated that shearer operator dust levels depend largely on how fast dust from the upwind drum spreads into the walkway. Water sprays on the shearer body can greatly affect the spreading of this dust because each spray moves air like a small fan, generating strong cross-currents of air around the shearer. Poorly designed spray systems, especially those with nozzles pointing upwind, will stir up much more dust than they sup-press. On the other hand, Improved systems may be designed to hold the dust cloud against the face while also suppressing It. In such arrangements the water is sprayed downwind and used with screens made from conveyor belting.

Jan 1, 1981

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By I. D. Shah

Thermal decomposition of copper (II) sulfate (CUS04) and copper (II) oxy-sulfate (CuO?CUS04) are important steps in the overall oxidative roasting of covellite (CuS) and chalcocite (Cu2S). Nonisothermal thermogravimetric techniques were used to investigate the decomposition reactions in flowing Na and air. Thermal decomposition of CUS04 and CuO?CUS04 followed "linear" kinetics with an apparent activation energy of 55±2 and 66±3 kcal per mole decomposed, respectively. These apparent activation energies comply with those previously reported when isothermal kinetic techniques were used. The addition of oxygen decreased the rate of decomposition, while small amounts of iron which were admixed with CuO?CUS04 did not have a significant effect. Neither oxygen nor iron had any appreciable effect on the apparent activation energy of the decomposition reaction.

Jan 1, 1972

By D. A. Wilson

A process was developed on a laboratory scale in which a solid waste byproduct from refining of secondary lead was converted into three valuable products. Roasted lead blast furnace matte was leached with water to recover copper. This was followed by brine leaching to recover lead. Residues were finally smelted to yield pig iron. Copper was precipitated as cement copper and the lead product obtained was a mixture of pure 3PbO.PbC12.xH20 and Pb(OH)C1. Copper recovery was 89 percent and lead recovery was 96 percent.

Jan 1, 1967

Detemine the elastic properties and structural integrity of a rock mass in situ. Approach An acoustic device that transmits and receives high-frequency seismic waves between boreholes was designed, built, and field tested. How It Works The acoustic cross-borehole apparatus operates by sending a seismic wave from a transmitter in one borehole to a receiver in a second bore? hole which may be located as far as fifty feet away, depending on the wave transmission quality of the rock. By measuring the wave's travel time and the distance between boreholes, the acoustic velocity of the rock mass can be determined. Characteristics of the seismic wave arriving at the receiver (such as the wave velocity, amplitude, and frequency content) are related to the physical properties of the geologic media, as calcu-

Jan 1, 1982

Detect hazards associated with abandoned mine openings through the use of integrated geophysical technology. Background Many abandoned mines in the U.S. present hazards to the public. The first step in abatement of these hazards usually requires locating the abandoned workings. Recent Colorado legislation resulted in a concerted effort aimed at mitigating the hazards associated with abandoned mine workings. The Colorado Department of Natural Resources-Mine Land Reclamation Division (CDNRMLRD) is responsible for locating and backfilling abandoned mine openings such as shafts, adits and collapsed features. Many shafts and adits can be located by inspection, other openings give little or no surface expression and must be located by drilling, or through the use of geophysical methods. A common method used for locating underground mine workings is to drill throughout the suspected area. However, it is prohibitively expensive to drill holes at the spacing needed to detect backlilled shafts and small voids associated with caving and/or chimneying. It may also be dangerous to move heavy equipment over shallow mined-out workings. Geophysical investigations that employ only a single method have had mixed success in detecting hazardous abandoned mine land cavities.

Jan 1, 1991

Improve the effectiveness of person-wearable self-contained self rescuer (PWSCSR) training by enhancing the memory retention of trainees in proper donning procedures. Background In the fall of 1989, a total of 185 miners and inspectors were trained by Bureau of Mines personnel to don the SR-100 PWSCSR using the Bureau's 3+3 method. With the exception of a few individuals, miners were trained underground in an area set up within their working sections. The instructional protocol was as follows: (1) after placing an SR-100 simulator (equipped with a cleaned and disinfected mouthpiece assembly) on the mine floor in front of the worker, a researcher guided him or her step-by-step through the complete donning procedure, (2) the miner was required to perform each step slowly, methodically, and correctly while being talked through the sequence, (3) following this pre-practice instruction, the apparatus was repacked and the subject donned the device without coaching, while being evaluated, (4) if an error was made, the worker received corrective feedback, the unit was repacked, and the entire donning trial was redone. This procedure was repeated until the miner achieved a perfect 3+3 sequence.

Jan 1, 1990

By Rollien R. Wells

A REPORT of technological advancements restricted to a specific 12-month period is impractical. Inherent in the nature and development of technology is the element of time; rarely can a new process or product be attributed to a particular year. An overall picture of general trends and pattern changes, however, is indicative of technological growth. This paper presents selected observations and discussions of current metallurgical research and practices in an attempt to develop' such a picture. Of the estimated $16.5 billion spent for research and development in the United States in 1962, at least 80 percent was earmarked for the aircraft, electronics, chemical, and machinery industries. Much of the effort was of the end-use variety and was oriented closely to the national defense and aerospace programs. Only a small fraction of the total research money was directed to studies of the utilization and improvement of metals. Even if the investigations in allied fields such as solid state physics are included, the total research expenditure for metal and mineral materials barely reached $500 million. An additional $200 million was spent by industry and government for development of minerals recovery and processing methods.

Jan 1, 1963

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By B. D. Hanson

The U.S. Bureau of Mines has developed an interactive computer program which enables the user to identify the effect of cutting system changes on relative dust generation and forces for continuous miner drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. One or more of these parameters may be changed to determine their individual or collective effect on relative dust generation and cutting forces. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs.

Jan 1, 1989

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

A computer model of an existing mine ventilation system can be executed using data developed from ventilation survey results. This model can then be used to analyze and evaluate proposed modifications to the system. The acquisition of field measurements during a ventilation survey and the corresponding development of this information into computer input data have been discussed in detail in the preceding chapters. In this chapter, the data are used in computer-oriented analysis of the mine ventilation system. The PSU/MVS was selected for use because of its advanced capabilities. MINE DESCRIPTION The mine chosen for this application is located in Western Pennsylvania. The Pittsburgh coal seam, having an average height of 5-1/4 to 6-1/2 ft, is mined under approximately 300 to 500 ft of cover. The mine preparation plant and shipping facilities are located at the seam outcrop along a river; mining has progressed from the outcrop to an area about 10 miles from the pit mouth so that there are extensive worked-out areas through which access is maintained to the current mining area. Coal haulage is by conveyor to an underground transfer point, located four miles from the pit mouth, and then by high speed rail haulage to the preparation plant. The rail haulage link is scheduled for replacement by a conveyor in the near future. Mining at the present time is limited to the room and pillar method using continuous miners. Longwall mining had been attempted in the past with only limited success; as a result, several panels originally laid out for longwall mining are currently being extracted by room and pillar work. The

Jan 1, 1977

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

This book has employed miners' narratives to illustrate basic concepts about the escape process. One of the most powerful means by which people make sense of their experiences is through the telling and internalization of stories [Bruner 1990]. By couching one's own and others' motives and actions in terms of a coherent narrative, a person is able to learn from mistakes and plan future behaviors that may help ensure survival. A growing body of research suggests that decision-making skills used to deal with emergency situations can be taught and assessed by simulations based on narratives from the real world [Bransford et al. 1986; Brecke 1982; Brener 1984; Connolly et al. 1989; Halff et al. 1986; Jones and Keith 1983; Lacefield and Cole 1986]. Such techniques have been used to address the decision-making of medical personnel, civil and military flight crews, and even people involved in broader life events such as political and military situations [Babbott and Halter 1983; Dugdale et al. 1982; Farrand et al. 1982; Gilbert 1975; McGuire 1985; McGuire et al. 1976; Flathers et al. 1982; Giffin and Rockwell 1984; Jensen 1982; Janis and Mann 1987]. Given the validity of this method of study and the promise it holds for helping people improve the quality of their responses to nonroutine occurrences, it is perhaps surprising that there have been no studies of emergency decision-making among blue-collar workers prior to those conducted by the present authors and their colleagues. The purpose of this chapter is to describe underground coal miners' decision-making performance on a table-top simulation whose problem structure is derived from interviews with a group of eight miners who escaped from the 5 Left section at Brownfield Mine. The exercise was constructed by a panel of domain experts (mine safety and rescue personnel) with the assistance of an educational psychologist. The simulation includes actual predicaments with wise and unwise decision alternatives that, in the opinion of these domain experts, are characteristic of such escapes. Results reported in this chapter are the scores of a sample of experienced mine workers who completed the simulation. Because the exercise is a series of objective performance tasks coupled with detailed and immediate feedback, this simulation can be used to teach and refresh critical escape skills, as well as to provide data concerning the proficiency of miners at the time of exercise administration.

Jan 1, 2000

By T. A. Sullivan

Research undertaken by the Bureau of Mines in 1938 has resulted in the development of titanium from a laboratory curiosity to a commercial metal. Along with processes for producing the metal, it was necessary for the Bureau to develop methods for analyzing the metal, raw materials, and intermediate products. Some of the methods developed have been published.3 4 5/ General Services Administration (GSA) was responsible for purchasing titanium metal under Defense Production Act contracts with commercial producers. GSA designated the Federal Bureau of Mines to analyze this metal and establish its compliance with Government specifications. A substantial quantity of tin was found in some of the samples analyzed, and in July 1957 tin was added to the list of impurity elements to be determined. The specifications limited the amount of tin in titanium sponge to a maximum of 0.10 percent. A program was immediately initiated to investigate methods and techniques for determining tin in the range of 0 to 1.0 percent. A method accurate at the 0.10 percent level was necessary, as this level was the critical range for acceptance or rejection of the metal.

Jan 1, 1960

By H. C. Miller

[California's sensational rise to supremacy as an oil-producing State in 1923 was accompanied by a loss of 62 lives. These 62 deaths were from oil-producing accidents alone and do not include fatalities at the refineries, on tankers, or on any work not directly connected with the drilling for and the production of oil. The number of facilities for 1923 was 82 per cent greater than in 1922, the next most fatal year, with a record of 34 lives lost. The data submitted in Table 1 show that for the calendar years 1917 to 1923 inclusive, an average of 4.74 million barrels of oil were produced per Vitality in the California oil fields. On this basis, the record for 1923, hough a trifle below the average, shove up slightly better than that for 1922.]

Jan 1, 1924