Search Documents

By William G. Pariseau

Elastic-plastic finite-element simulation of cut-and-fill stoping in deep, narrow veins shows substantial quantitative agreement with field measurements of stope closure and fill pressure made at two mines in the Coeur d'Alene mining district of northern Idaho. The simulation procedure, validated by field data, was used in an analytical study of vein-wall closure and sill-pillar stress as influenced by fill modulus, rock modulus, and premining stress. Ratios of closure and pillar stress in the filled stopes to closure and pillar stress in the unfilled stopes are used as prediction indices for fill performance. In general, the support capability of fill increases dramatically as the ratio of fill modulus to rock modulus approaches 1. A significant reduction in closure .from the open stope--up to 75 percent--occurs with a relatively low-quality 10-ksi-modulus fill (rock modulus of 1,000 ksi). However, a higher quality fill is needed to achieve a substantial reduction in pillar stress from that of the open stope. A 100-ksi-modulus fill reduces pillar stress in both the 36-foot and l6-foot pillars (vein width is 10 feet) by about 50 percent relative to the open stope.

Jan 1, 1976

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By H. W. Gillett, E. L. Mack

"This report describes the trend of developments in electric brass-furnace practice in the last two years, and supplements Bureau of Mines Bulletin 202, ""Electric Brass-Furnace Practice"", which was published in 1922. In that bulletin it -as pointed out that some of the lines on which electric brass-furnace progress would take place were clear, but others were less so.Developments in foreign countries.Foreign brass-melters have not yet adopted electric melting to an extent comparable to its use in the United States. It is doubtful Whether all foreign countries combined use 100 electric brass furnaces; of these about 35 are of American make (Ajax, Detroit, Baily) and are operating in Canada, Mexico, England, France, Japan, Sweden, Switzerland, Spain, Norway, Germany, Argentina and Czecho-Slovakia.`The Rennerfelt furnace finds some use in Sweden (1)c, notwithstanding its high metal loss on alloys high in zinc, Two German firms are reported(2) to be using the Rochling-Rodenhauser induction furnace on bronze, the average energy consumption being given as 400 kw.-h. per ton. No comment is made on any trouble from the ""pinch effect"", A firm in Switzerland is reported (3) to use three 600-lb., direct-arc furnaces of its own design to melt babbitt, antimonial lead, coinage silver, nickel, copper, and brass. The metal loss on yellow-brass turnings is high. Use Of a direct-arc furnace in England, with precautions aimed to prevent surface overheating, vas abandoned (4) in favor of an Ajax furnace."

Apr 1, 1924

By R. V. Lundquist

A method was developed by the Federal Bureau of Mines for evaluating viscosity data from slurries obtained in leaching sinters from the lime soda sinter process for extracting alumina from aluminous silicates. The logarithm of the viscosity was observed to be a linear function with time. The slope of the plotted line provides a means for evaluating viscosity behavior in a lime soda sinter blurry and also a means for comparing gelation characteristics directly with other variables in the lime soda sinter process. This report presents one aspect of a continuing study by the Bureau of Mines on methods for treating siliceous aluminum ores. It is one of the many programs of the Bureau concerned with conservation, development, and use of our domestic minerals resources. Previous investigations of lime soda processes, both by the Bureau4-7/ and industrial concerns, have demonstrated that sintered materials containing CaO, Na2O, A1203, and S102 in various combinations exhibit a tendency to gel or set when mixed with water or other extraction solutions. Gelling prevents satisfactory recovery of alumina and in extreme cases prevents operation of an extraction plant.

Jan 1, 1960

By Robert J. Anderso

Few elements have received more attention and developed greater interest in the last ten years than titanium. The substantially pure metal has been din...ie. cult to isolate, and so far has been little employed oommercially, but the use af alloys and chemical compounds of titanium has increased markedly in recent years. The earlier attempts at preparing pure titanium resulted in various impure forme which, from their metallic appearance, were always mistaken for the metal. Hunter in 1910 isolated pure titanium by the reduction of titanium tetrachloride with sodium. This brief statement is issued by the Bureau of Mines in response to numerous inquiries which have been received concerning titanium. More complete in. formation on the metal may be had by consulting the referenpes appended. The Literature is voluminous and only the more important references are Riven. It has been drawn upon freely in preparing this report; also information was supplied by M. g. Hunter, Arthur Braid, M 1. Schmid, C. M. Johnson, N. B. Hoffman, and de Courny Browne. The pioneer investigator in titanium is A. IL Rossi.

Oct 1, 1922

By C. J. Chindgren, L. C. Bauerle, J. B. Rosenbaum

Modifications of the conventional method of preparing ductile vanadium metal by calcium reduction of V2 05 in a bomb were explored for clues to a more economical procedure . The modifications examined included ( 1 ) omitting the gas purge of the bomb ordinarily used for eliminating atmospheric nitrogen , (2 ) using low- grade vanadium feed materials , ( 3 ) using alternative reductants , such as aluminum , magnesium , and silicon , and reductant mixtures , and ( 4 ) bomb refining of aluminothermic metal produced in open- vessel reductions . The most promising modification appeared to be bomb refining , using calcium to purify vanadium metal -- of low aluminum but high oxygen content-- prepared by open- vessel aluminothermic reduction of vanadium pentoxide .

Jul 1, 1960

By Harry Vivian

This paper deals principally with the retreating method of mining as applied in the Calumet & Hecla Consolidated Copper Co.'s deep Conglomerate mine, pointing cut some of the difficulties encountered in deep mining and describing the particular methods used at Calumet to carry on a large-scale operation at great depth with a minimum hazard factor. The circular is one of a series dealing with mining methods and costs which is being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is due to those officials and operating heads of the Calumet & Hecla Cc. whose years of familiarity with the conditions developing at the Conglomerate mine as great depth was attained have enabled them to contribute valuable information to the subject of deep-mining problems.

Jan 1, 1931

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By L. H. Wullstein

Bureau of Mines research on methods for reclaiming land disturbed by the minerals sector of the economy has produced a specific procedure for effectively germinating seed of Indian ricegrass, a drought-tolerant plant valuable for reclaiming arid and semiarid sites. This report describes the procedure which consists of acid-treating the seed followed by temperature and light cycling treatments. Use of the procedure resulted in an average germination rate of 29 percent, ranging from 18 to 56 percent. Seed subjected to long cold treatment but with acid treatment yielded an average germination rate of 9.2 percent, ranging from 6.6 to 14.7 percent. Untreated seeds (controls) gave germination rates less than 0.1 percent.

Jan 1, 1979

By V. E. Homme

This report describes methods of using sodium for reducing titanic chloride, developed as part of Bureau of Mines activities at Boulder City, Nev., to improve the extractive metallurgy of titanium. Theoretical indications pertaining to the major chemical reactions and possible side reactions of the process are compared with experimental observations. Low-temperature reduction equipment is described, in which titanic chloride was reduced with sodium at temperatures between 97.5° C., the melting point of sodium, and 200° C. Techniques employed in making reductions in ball-mill and high-surface sodium reactors are given.

Jan 1, 1958

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1992

By C. H. Elder, Maurice Deul

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coalbed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 ft3 /day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By Harry R. Nicholls

As part of the pre- and post - shot mine examination at Project GNOME , acceleration data were recorded underground from a series of chemical explosive shots . The cube root of the charge weight was used to scale acceleration and distance because charge weight was not constant . Regression analysis of particle acceleration - distance data gave the following propagation equation : A W1 /3 = 5.10 x 105 ( R / W¹ / 3 ) −2 .43 The quantity A W1 /3 is scaled particle acceleration expressed in g's - lbs¹ / 3 , and R/W1 /3 is scaled distance expressed in ft / lbs¹ /3 Data obtained from the nuclear explosion were scaled and fall within one standard deviation of the calculated propagation law for the smaller shots . Cube root scaling laws were adequate to group acceleration data from explosive charges varying by a factor of more than 1 x 10 in charge weight and over shot - to - gage distances varying from 100 to 46,000 feet . Data obtained from a series of small tests provided sufficient data from which reliable predictions of acceleration could be made for the large nuclear explosion .

Jan 1, 1964

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

During the 1990s, the former U.S. Bureau of Mines conducted a number of field studies in which the performance of different types of roof bolts were evaluated in different geologic environments. The studies used a standard suite of measurements, including multipoint extensometers, strain-gauged roof bolts, and roof bolt load cells. The sites were chosen to investigate the effect of a variety of parameters, including installed tension, bolt capacity, grout annulus, and horizontal stress orientation. Although not fully successful, the measurements provided valuable insights into each of these issues. They also showed that instrumentation and monitoring have important advantages over observational methods for comparing the performance of different roof bolting systems.

Jan 10, 2000

By Oliver Bowels

Many inquiries are received by the United States Bureau of Mines for the names of elementary books on geology, mineralogy, methods of identifying minerals, prospecting, and similar subjects. In response to this demand the following brief bibliography has been prepared. As many of the inquiries are received from those who have limited technical knowledge of the subjects involved, the bibliography includes the simpler texts which present the subjects in nontechnical language. Other texts contain glossaries which define the technical terms used. A short note following the title indicates the character of each book, the number of pages, and the price. Thus, elementary mineralogists or geologists, prospectors, mineral collectors, nature students, or travellers may select the texts that best suit their requirements and their capabilities. To supply the needs of more advanced students, quite a number of the standard texts used in schools and colleges are included in a second group. A short list of books on economic geology and mineralogy has also been added.

Jan 1, 1929

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1951 are presented in this bulletin under the following general heads: (A) General injury experience: Tables 1 to 18: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major and detailed injury agencies, and distribution of injuries by part of body and days of disability. (B) Selected injury data: Tables 19 to 43: Contain current data on various selected factors of operating and physical conditions that contributed to the occurrence of injuries at bituminous-coal, lignite, and anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy or nongassy, types of cap lamps, explosives, and combination of factors that influence mine safety. (C) Injury experience by States: Tables 44 to 50: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major causes and principal agencies, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Major disasters: Table 51: Lists the coal-mine disasters that occurred during 1951, giving location, source, and cause. A major disaster in coal mining is defined as a single accident in which or as a result of which five or more men lost their lives. (E) Historical coal-mine injury experience: Tables 52 to 86: Contain data on injuries, injury-frequency rates, employment, and production at bituminous-coal, lignite, and anthracite mines from the earliest records through 1951.

Jan 1, 1955

To provide a means for rapidly evaluating proposed mine layouts in order to avoid potential hazards while minimizing loss of coal. The Approach: Development of a computer program that will compute many possible mine layouts by changing the mine plan until the arrangement giving minimal hazards with optimum extraction is found. How It Works: The Hazard Evasion Program for Mine Planning, developed by the Bureau's Denver (Colo.) Mining Research Center, tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on the criteria of maximum safety for workers with minimum abandoned coal), limits the number of choices that need to be considered and appraised for applicability to a given mine scheme. The program is applicable for room and pillar or longwall mining, for oil and gas well hazards, and for other hazards that can be described mathematically such as channel sands, potential bad roof areas, faulting, voids, or water pockets.

Jan 1, 1974

By A. J. Barry

To determine the torque-load relationship for SIB-inch (nominal)-diameter roof bolts, the Bureau of Mines tested 5 makes of expansion shells and 2 types of bolts (regular and high-strength) in 2 sandstone and 2 shale mine roofs. Unused flat-steel bearing plates in as-received condition were used in these tests. The relationship between torque and load was found to be approximately 50 pounds of load per foot-pound of torque for both the regular and high-strength bolts. This relationship is valid up to 130 foot-pounds for the regular bolts and up to 175 foot-pounds for the high-strength bolts. A torque of 130 foot-pounds on a regular bolt will produce a load of 6,150 ± 1,910 pounds 90 percent of the time, and a torque of 175 foot-pounds on a high-strength bolt will produce 8,050 ± 2,750 pounds 90 percent of the time. Above these values, the torque-load relationship tends to be erratic due to binding between the bolt and plug threads. Binding causes excessive torque to be expended in producing torsion in the bolt rather than tension. This torsion adversely affects the yield load of the bolt. Therefore, the installed torques should not exceed the 130-and l75-foot-pound values. A statistical analysis of the data showed that the torque-load relationship was not significantly affected by the type of bolt or expansion shell unit but might have been affected by the type of rock.

Jan 1, 1956

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young's modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954