Search Documents

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Black Rock Desert Wilderness Study Area (WSA) (NV-020-620), which covers approximately 319,000 acres in Humboldt County, Nevada. About 90% of the WSA is underlain by Pleistocene desert playa sediments; the remainder is comprised of Jurassic-Triassic metamorphic rocks, a Cretaceous intrusive and Tertiary volcanic rocks. Most of the WSA is within a down-dropped fault block of the Basin and Range physiographic province. No mines or evidence of major exploration were identified within the WSA; but five claim blocks within or adjacent to the WSA and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but anomalous gold, silver, and indicator element content of samples taken near Pinto Hot Springs indicate resources may exist. Lithium content of samples from near-surface sediments on the desert playa is too low for resources, out geologic conditions are favorable for higher concentrations at depth. Occurrences of zeolites are not considered to be of commercial interest. Approximately 27,000 acres are held under geothermal lease, and most of the WSA is of interest for oil and gas. No evaluation of these commodities was made by the Bureau of Mines

Jan 1, 1985

By A. L. Engel

High extractions of lead, gold, and silver resulted from treatment of an oxidized, arsenical refractory ore by chloride volatilization. The ore was roasted in an oxidizing atmosphere at 1,000° C. for 1 hour. The chloridizing reagent was 300 pounds of CaC12?2H20 per ton of ore. Ninety-nine percent of the lead, 98 percent of the gold, and 96 percent of the silver, and only 6 percent of the arsenic, were volatilized. These results indicated that a satisfactory method could be developed for treating this type of ore. Recovery and separation of the volatilized values and developing metallurgical and operating data for this process require further investigation on a more extensive scale. Tests by gravity concentration, flotation, and cyanide leaching did not give satisfactory results.

Jan 1, 1958

By R. L. Hopkins

Some typical thiacyclopentanes and thiacyclohexanes were synthesized to provide reference compounds needed for the identification of sulfur compounds in crude oils. Two general methods of synthesis were employed: (1) cleavage of 2-alkyltetrahydropyrans with hydrogen bromide followed by the reaction of the resulting dibromoalkanes with sodium sulfide and (2) the catlyzed reaction of cyclic ethers or 1)4-or 1)5-alkanediols with hydrogen sulfide. Both methods produced mixtures of 2-alkylthiacyclopentanes and 2-alkylthiacyclohexanes with 2-alkyltetrahydropyran as the starting material. The structures of the reaction products were established by analysis for sulfur; desulfurization; gas-liquid chromatography (GLC); mass, infrared, and nuclear magnetic resonance (NMR) spectra; and an alternate synthesis. The synthesis of the cyclic sulfides contributed substantially to the identification of 10 members of this class of sulfur compounds in crude oil.

Jan 1, 1967

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By Mary A. Barrett

The Bureau of Mines conducted a laboratory-scale investigation of grouting mixtures containing iron or aluminum to determine the existence of health or explosion hazards, due respectively to oxygen depletion or hydrogen emission. Mixtures containing iron created an oxygen deficiency in less than 24 hours and released small amounts of hydrogen; a health hazard could occur but only under extremely unfavorable conditions. Mixtures containing aluminum released little hydrogen and consumed little oxygen; however, if improper on-site mixing yielded high local metallic aluminum concentrations, enough hydrogen might be released to produce an explosive atmosphere in a confined space.

Jan 1, 1969

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By Foster Fraas

Electrostatic separation depends on a number of electrical and mechanical properties such as conductance, contact potential, dielectric constant, and particle shape. In routine testing it is desirable that the application of each of those properties be investigated. The conductance property is best utilized in a separator having an ionic field, whereas the contact potential requires a separator with a pure static field. Dielectric constant and particle shape also influence the response in these two fields. There is no separator on the market that can be adjusted for all these requirements. The separator described in this paper is satisfactory for this purpose and is provided with a dielectric electrode, which permits formation of high-intensity static fields.

Jan 1, 1951

By E. D. Gardner

"In recent years efficient safety organizations have been considered essential at all well-managed metal mines. Statistics from numerous mines throughout the country show that the expense of operation of these safety departments is repaid many times by the saving due to fewer accidents. Men trained in first aid, mine rescue and fire-fighting are important parts of the safety organization at most mines. It is more desirable, however, to lay stress ma accident prevention and fire precautions rather than on first aid and fire fighting. Both of these phases of safety work have been well developed in the Globe Miami district. The co-operative mine rescue organization* in this district under Orr Woodburn, is one of the best in the country. Mine rescue teams are kept trained at all the mines and the oxygen breathing apparatus is constantly maintained in good condition. Miners are also trained in first aid, and are offered incentives to make themselves proficient both in mine rescue and first-aid work.The Old Dominion Company is among the leaders in the safety movement in the Globe-Miami district. The safety department at this mine was established January 1, 1914, and has been developed to a high degree of efficiency. W. G. McBride, general manager of the company, takes an active part in the safety work and has given Albert Talon the safety inspector, his active support in developing the organization. The success of the department is dos largely to the ability, tact, and personality of the men directing the work.The following description of the establishment and operation of the safety organization at this mine was prepared from information supplied by Mr. Tallon."

Jun 1, 1921

By D. Harrington

We Americans fondly believe that ours is the greatest , most progressive and most civilized country in the world , but the cold statistical facts reveal that we apparently have little appreciation for the lives of those whose efforts of various kinds give us whatever greatness we have . The latest available statistics indicate that the annual death rate per 100,000 persons , from accidents is nearly 80 , or far higher than that of any other country in the world ; it is more than double the rate in Denmark , Belgium, Netherlands , France , Sweden , Italy , Ireland , Germany , Norway, and Austria; it is practically double the rate in England and Wales and in Japan , and is from 25 to 60 per cent higher than the corresponding rate in Scotland , New Zealand , Australia, Switzerland , and Canada . And added to this is the fact that of the main industries of the United States mining has by far the worst accident record , viewed from either the frequency or the severity basis . The National Safety Council's latest figures for 27 of the country's main industries give mining the highest or worst accident frequency rate, 74.43 in 1929 ; meat packing comes next with 55.94 , and construction third with 50.41 . In accident severity in 1929 mining also was the worst offender , with a rate of 9.99 ; quarrying is second with 6.11 , and construction third with 4.62 . Metal mining's frequency rate in 1929 was 52.16 , as against 69.25 for bituminous coal mining ,99.68 for anthracite mining, and 74.43 for the entire mining industry ; accident severity for metal mining in 1929 was 5.99 , as against 11.69 for bituminous coal mining , 10.87 for anthracite mining , and 9.99 for the mining industry as a whole . Although this figure indicated that metal mining is on a much safer plane than either bituminous or anthracite coal mining, the frequency rate of 52.16 for metal mining was higher in 1929 than the frequency rate of all but one of the other 26 industries about which data are available ; the metal mining severity rate of 5.99 , while much better

Mar 1, 1932

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller: Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone. Another example of the waste of large volumes of gas is in the Turner Valley field of Canada, 6 where 250,000,000 cubic feet of gas is being burned daily in flambeaus, as there is no present outlet except at prohibitive cost.

Jan 1, 1931

By H. A. Doerner

For the past three or four years attention has been attracted to the deposits of lead vanadate in the Goodsprings , Nevada , district . Some ore running as high as 9 per cent 205 has been produced , but most of it runs from 0.5 to 3 per cent . Only a little ore , and that of the richer sort , has been shipped , since the low- grade ore will not stend the cost of shipment and no concentration mill has been available . Preliminary experiments indicate that chemical treatment of the low- grade ore without concentration is not feasible . Its treatment therefore involves two distinct problems ; first , mechanical concentration ; and second , a smelting or chemical treatment to obtain the lead and vanadium in marketable form . Upon this basis the work has been conducted . The writer wishes to acknowledge the excellent work done by J. T. Norton and Virgil Miller on table concentration and by J. E. Conley , who suggested and did preliminary work on the direct smelting method . Many helpful suggestions were received from Dr. S. C. Lind and John Gross of the Bureau of Mines . The ores were furnished by Mr. Frank Williams and Mr. James Ewing .

Jan 1, 1923

By R. V. Ramani, J. M. Mutmansky, J. Qin, J. Organiscak, R. Bhaskar

"The results of a two—year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the ¬analysis results and conclusions of the study are discussed.The results of the study indicate that the quartz contents of the airborne dusts are generally higher than those in the host material and bulk samples; and the quartz content increases with decreasing size of the airborne dust. The source for quartz appears to be the roof and the floor materials rather than the coal seam itself. It also appears that the material containing quartz may be breaking into a different size distribution than coal.INTRODUCTION Without doubt, the potential for permanent and severe health damage exists due to respirable dust in the work environment. The attention directed at the reduction of respirable airborne dust to levels below those specified in the law and the achievements to date in meeting these standards are but a reflection of the recognition by many parties government, industry, and labor - of this potential and the need to reduce it.The ambient dust standard in underground U.S. coal mines (2 mg/s3) has a qualifier (Code of Federal Regulations, Title 30, Part 71.101) to determine an applicable dust standard when a respirable dust sample contains more than 5% quartz. This standard is frequently referred to as the ""reduced standard."" The reasoning behind the reduced standard is the relative toxicity of the quartz dust compared to that of pure coal dust. As the quartz levels in samples increase, the applicable standards become more stringent and maintaining the workings in compliance becomes increasingly difficult.The number of underground work locations operating under the reduced standards has shown a dramatic increase since 1980 (Figure 1). For comparison purposes, there were no mining entities operating on reduced standards prior to 1977. The emergence of this problem, which affects the health and safety standards on one hand and creates severe compliance problems on the other, has been rapid."

Jan 1, 1990

By John B. Knaebel

Hammer machines are now widely used for underground sampling and exploration. Their application to such work can be divided into two classes - sampling and testing with ordinary drilling equipment to shallow depths of 22 feet or less, and "long hole" drilling with heavy machines and special equipment to depths of as much as 250 feet or more. In the first category hammer drills are employed for either of two distinct purposes: first, as a means of checking the results of grab or cut samples or, in certain types of ore deposits, as a substitute for these methods; and second, as a method of sampling the ground 5 to 20 feet beyond existing faces and thus aiding in the control of stoping operations or in the direction of development headings, as the case may be. The deep-hole drill, in the second category, has proved to be a valuable adjunct to the old established methods of exploring, end developing ore, provided it is employed under natural conditions to which it is suited, handled by men thoroughly familiar with the technique of its operations, and used with its possibilities and limitations clearly understood.

Jan 1, 1932

By D. R. Corson

The Bureau of Mines instrumented two similarly backfilled stopes--one filled in the normal manner and the other with the fill densified using vibratory compactors--to evaluate the effect of fill compaction on subsequent vein-wall closure proposed as a adjunct process for strengthening cemented fill. Hydraulic pressure cells to monitor pressures within the fill and mechanical closure devices to measure vein-wall movement and the procedure for their installation are described. The field compaction work was generally performed manually by utilizing small commercial concrete vibrators. A prototype immersible vibrator using slusher cables to propel the vibrator in the stope was used on several lifts of fill. Although compaction efforts were less effective than anticipated in increasing the final density of fill, analysis of the field data does indicate somewhat improved strain characteristics and an increased pressure buildup for the densified fill. The effects of a prolonged period of inactivity and of rock burst occurrences in the immediate area are also reflected in plots of strain and pressure within the two instrumented stopes.

Jan 1, 1971

By T. T. Campbell

A survey of the literature eras made covering the use of aqueous non-aqueous, and fused-welt systems for the electrowinning or electroplating of molybdenum metal. The survey was prepared in order to provide background for further investigations directed toward the electrodeposition of pure molybdenum metal from either aqueous or nonaqueous mediums. While a thorough effort was made to cover all available references, a critical review was not attempted nor does this survey pretend to be exhaustive in nature.

Jan 1, 1955

By Forrest T. Moyer, Nina L. Jones, Mary B. McNair, Virginia C. Berté

To keep the mineral and allied industries informed of trends in the causes of accidents, and to point out the need for corrective measures, the Bueau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1963 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings:

Aug 1, 1965

By Michael M. Hamilton

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 37,542-acre portion of the 57,002-acre Riordan?s Well Wilderness Study Area (NV-040-166) in order to evaluate its mineral resources. The area studied is located in Nye County, NV, about 60 miles southwest of Ely, NV. Subeconomic mineral resources of limestone and sand and gravel were identified in the study area. The Troy and Irwin mining districts, 4 miles to the west, were active between 1868 and 1963, producing small amounts of gold, silver, lead, and tungsten from mines well outside the study area. Except for minor prospecting activity, most mining activity in the study area has been since 1980, consisting of claim locations and geochemical surveys.

Jan 1, 1987

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010