Search Documents

By James A. Brierley

Wastewater from uranium mines in the Ambrosia Lake district near. Grants, New Mexico, U.S.A., contains uranium, selenium, radium, and molybdenum. The Kerr-McGee Corporation has a novel treatment process for waters from two mines, sections 35 and 36, to reduce the concentrations of the trace contaminants. Particulates are settled by ponding, and the waters are passed through an ion exchange resin to remove uranium; barium chloride is added to precipitate sulfate and radium from the mine waters. The mine waters are subsequently passed through three consecutive algae ponds prior to discharge. Water, sediment and biological samples were collected over a 4-year period and analyzed to assess the role of biological agents in removal of inorganic trace contaminants from the mine waters.

Jan 1, 1981

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By J. W. Paul, J. N. Geyer

"GENERAL STATEMENTThe purpose of this report, which is the first of a series of three covering mines in the Fairmont district of West Virginia, is to give the result of a' study conducted in seal mines to ascertain the nature of the safeguards employed to prevent injury to the workmen from falls of roof and coal. In presenting the subject matter, consideration must necessarily be given to factors, features, and conditions such as method of mining, timber regulations and practices, supervision and natural conditions; and, for comparative purposes, a certain amount of statistical matter bearing upon the relation of fatalities and injuries to their causes, tonnage produced, men employed, days worked, and time lost.Those features and practices found to promote safe protection are summarized and suggestions made for such additional safeguards and practices as appear to give greater protection against injury from falls of roof or coal.ACKNOWLEDGMENTSThis study of falls of roof and coal in mines in Harrison County has been conducted by the U. S. Bureau of Mines in cooperation with R. M. Lambie, chief of the Mining Department of the State of West Virginia who assigned L. W. Brown, a district mine inspector, to assist in the field work and in the preparation of individual reports on each mine visited in this study. The writers acknowledge the helpful suggestions and cooperation given by these officials, the latter of whom assisted in the field work and prop red most of these sketches for the individual reports which wore submitted to the operator by the chief of the department. Thin report is a summary of the contents of the individual reports heretofore furnished the individual operator."

Aug 1, 1931

By James R. Boyle

The Bureau of Mines initiated a program to address short-and long-term objectives of wetlands restoration as a option for reclamation of lands mined for phosphate. The short-term objectives were to identify a suitable wetland test site, initiate an extensive premining monitoring plan, develop an acceptable mining plan, and recontour and revegetate the test site. These goals were accomplished using a unique combination of expertise provided by Federal and State agencies and private industry. A 6.5-ha forested wetland with an associated streambed was offered by private industry as the test site. A premining monitoring program was established and carried out from May 1982 to October 1983. A control site was established to determine ecological changes unrelated to mining. Clearing and mining began in October 1983 and was completed in April 1984. Grading and streambed restoration was completed in February 1986. Revegetation of the site was completed in February 1987. The program to meet the long-term objective of postmining monitoring is described.

Jan 1, 1988

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By B. C. Christensen

The contract objectives are (1) to develop safe practice guidelines which will minimize the chance of fires in underground fueling areas and (2) to develop a low-cost, reliable, automatic fire protection system for underground fueling areas. The effort described by this report covers the period from 21 June 1976 to 30 September 1977 and accomplished the following tasks: ? Preparation of Data Plan and Data Acquisition, mainly through visits to sixteen mine sites and a literature survey. ? Analysis of the accumulated data, providing design inputs for (a) evaluation of the fire problem; (b) development of safe practice guidelines; and (c) development of recommended design concepts for automatic fire protection systems. ? Preparation of safe practice guidelines for underground fueling areas. ? Preparation of recommended design concepts for automatic fire protection systems for underground fueling areas. ? Design and fabrication of fire protection system for installation at Pine Creek Mine, Bishop, California. ? Install system and perform underground fire tests at Pine Creek Mine.

Jan 1, 1977

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic suppler was evident. During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Lines has ascertained the potash resources in certain district's through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the massage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By Ignaz Lichtig

[IN CONNECTION with its work on the conversion of coal to liquid cud gaseous fuels,3 the Bureau of Mines has always striven to keep informed of developments in this and related fields so that unnecessary duplication of effort could be prevented and so that useful ideas, presented in scientific and technical literature, could be evaluated as quickly as possible. Thus the E has compiled expensive literature and patent abstracts on the Fischer-Tropsch synthesis4 and hydrogenation d e venation of coal at elevated h temperatures and pressures.5 6 This publication differs from the references just given in that it covers patent applications, which may or may not have been approved for issuance as a patent, and also includes later material. The patent literature is, of courses, a valuable source for new ideas. German patent, have been particularly useful in this field because both processes for the complete conversion of coal to fluid fuels originated in Germany and were thoroughly investigated there because of the shortage or of indigenous fluid fuels. Among the German literature relating to these processes are patent applications. In contrast to the United States, Germany has a system in which applications are published before the final patents are issued. This arrangement permits the public to view all the applications and not just those for which a patent was granted as is done in the U.S. system. When main of the invention are judged not patentable by the German Patent Office, such documents nevertheless may contain useful ideas for scientists and engineers.]

Jan 1, 1961

By Walter C. Woodmansee

The only reported mineral production in 1977 was small output of alluvial gold, valued at an estimated $54,320.2 In addition, marine shells are gathered for use in lime manufacture, although output was not reported. Proposed development of a bauxite mine and smelter, involving Rennell and Vaghena Islands, was deferred in June. Conzinc Riotinto of Australia Ltd. (CRA), in partnership with Mitsui Mining & Smelting Co. Ltd., and the Solomon Government, with- drew from the project, and Mitsui, which conducted a feasibility study and metallurgical testing of the bauxite, decided to defer further work because of slack demand for aluminum in Japan and difficulties in arranging financing. The Mitsui feasibility studies reportedly indicated that the project could be viable despite technical difficulties and relatively high initial investment costs. The project was to produce 1.5 million tons of bauxite and 600,000 tons of alumina per year from reserves totaling 60 million tans at 45% to 50% A1203.

Jan 1, 1981

By Thomas M. Barczak

Roof support technology for longwall tailgates has changed dramatically during the past decade. Filling tailgates with conventional wood cribs is becoming the exception rather than the rule. Modern engineered timber support systems and a host of other alternative support products provide far greater capacity as well as stiffer response, thereby allowing the supports to resist roof movement with much less displacement than the soft wood cribbing used in the past. For these reasons, these products can provide superior roof control. In addition, the material handling requirements for support installation have now become a major consideration in the support design and selection process. Products such as conventional wood cribbing that require piece-meal construction of bulky, heavy components have diminished, while prop-type supports and products that can be installed with machinery and pumpable support technologies have grown in use resulting in fewer injuries to mine workers. Now, the opportunity exists to provide the safest, most cost effective support system, through engineering design rather than by trial and error and to optimize the use of the support system chosen. Yet this is rarely done. The key to accomplishing this task is to understand the interaction of the support system with the ground conditions at the installation site. A major focus of the paper is to conceptualize the support and interaction through the use of a ground reaction curve which relates the support resistance to the convergence of the longwall tailgate. The goal of any roof support design is to control the ground deformations and maintain the structural integrity of damaged or broken ground to the extent possible to provide a stable mine opening. In general, deformations will be a function of the stress environment and inherent strength of the surrounding rock mass. However, if the deformations are intimately linked to the stress changes such that the deformation can be controlled by the load resistance or reinforcement provided by a roof support system, then the loading behavior can be described as load-controlled. Conversely, if the deformation occurs irrespective of the installed support (assuming practical limitations), then the loading behavior is described as displacement-controlled. In this case, the deformation can be considered irresistible from a practical standpoint. In this context, the nature of the loading has significant consequences on the support design requirements. Finally, examples using the NIOSH Support Technology Optimization Program (STOP) to develop design criteria using ground reaction data from underground studies and ways to include uncontrolled convergence as part of the design criteria for standing roof supports will also be discussed.

By D. Harrington

This circular presents part I of a series of papers of a review of the literature on air conditioning in mines, with particular reference to the health, safety, and efficiency of miners. It deals with the physiological aspects of exposure to air contaminated by organic matter, noxious and toxic gases, and dusts that emanate from various sources in underground workings; part II will discuss the relation of abnormal mine temperatures and humidities to the health and efficiency of minors; and part III will describe theoretical and practical methods of air conditioning mines to correct or alleviate the conditions mentioned and will discuss the results attained by some of the systems now in use in various parts or the world.

Jan 1, 1938

By H. F. Coward, G. W. Jones

"IntroductionIn the course of an investigation on the influence of black damp (a mix of nitrogen and carbon dioxide) on the limits of inflammability of fire damp (methane) in air, some new information was obtained concerning the factors that determine whether or not a gas mixture is capable of self-propagation of flame. Volume for volume, carbon dioxide exceeds nitrogen in its extinctive action on flame, an effect which is generally attributed to the higher molecular heat capacity of the former. Argon, a as of lesser heat capacity than either, proved to Lave less extinctive notion. If, as seemed likely, the extinctive action of a chemically inert gas could be attributed entirely to its heat capacity, then helium should behave like argon; equal volumes of these two oases should exhibit equal extinctive action, for their molecular heat capacities are nearly identical at laboratory temperatures and, in all probability, remain constant up to and beyond flame temperatures. The experiments reported here show, however, that helium has proved to be more extinctive of methane flames than argon.Method Used in ExperimentsThe limits of inflammability of methane, in various ""atmospheres"" composed of mixture of air with one or other of the diluent were determined in a vertical glass tube, 6 feet long and 2 inches in diameter. The lower end of the tube was opened by sliding away a ground-glass joint and the flame of a small spirit lamp was immediately passed across the aperture. The tube was sufficiently long to enable observers to judge whether a flame was self-propagation for if a mixture were incapable of continued self-propagation pf flame, the lamp of flame formel above the source of ignition was extinguished within feet of its passage up the tube."

Jun 1, 1926

By John J. Baz-Dresch

Catalyzed diesel particulate filters (CDPF's) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals' Cannon Mine first installed CDPF's in 1987, and currently has 12 diesel-powered vehicles equipped with CDPF's. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF's used at the mine was periodically evaluated in the USBM's diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM's evaluation of this CDPF, to describe the Cannon Mine's experience and cost analysis of using CDPF's, and to make recommendations for the future use of CDPF's. CDPF's improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF's account for 0.8 to 4.9 pct of the vehicles' operating cost at the lVine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 2010