Search Documents

By James Paone

This report on the state of the art of horizontal boring technology for underground power transmission installations was prepared by the Bureau of Mines at the request of the Department of the Interior. This paper describes the different machines and methods used in augering, impacting, pushing, drilling, and machine tunneling horizontal holes through soil and rock. A review of the borehole survey and guidance tools and techniques applicable to these methods is also given. Nonboring methods used for emplacement of power distribution and transmission lines are briefly discussed. The paper ends with a brief technical forecast, an analytical summary of the state of the art, and recommendations based on power industry needs. Horizontal boring techniques for power distribution lines installation are adequate to meet the requirements of the power industry, particularly where such burial involves relatively short distances in soil or soft rock. For burying power transmission lines, particularly in the harder rocks and over relatively long distances, horizontal boring methods are not as well advanced. Research and development as well as economic incentives to equipment manufacturers could substantially improve the state of the art. Obstacle detection and guidance systems for directing boreholes to specified targets need major improvements to meet the requirements of the power industry for underground burial of distribution and transmission lines

Jan 1, 1968

By P. G. Guest

MANY of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed in operating and anesthetizing areas. When ether was first introduced, candles,5 gaslights, and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions-many of them fatal to patients-have been attributed, with good reason, to sparks from static electricity.

Jan 1, 1953

By John T. Neubert

Between 1988 and 1990, the U.S. Bureau of Mines studied the mineral resources of San Juan National Forest to appraise and determine types and locations of deposits that could be mined economically now and in the foreseeable future. The study included a comprehensive field examination and literature search. Substantial amounts of lead, zinc, copper, gold, and silver have been mined from within the Forest in the La Plata, Rico, Silverton, and Dunton areas. At least one buried 200 million ton stockwork molybdenum deposit occurs in the Rico area. Similar size porphyry copper deposits occur at the surface and about 1,700 feet below the surface in the Bedrock Creek area of the La Plata district. Numerous smaller base-and precious-metal and uranium deposits have been prospected and mined throughout the Forest. Coal, oil, and gas have been or are currently being produced in the western and southern parts of the Forest. Carbon dioxide occurs in the western part of the Forest. Strategic elements occurring within the Forest include platinum, palladium, cadmium, gallium, indium, bismuth, and tellurium; however none of these elements is economically recoverable at present. Several geothermal areas are scattered across the eastern two-thirds of the Forest. Industrial minerals within the Forest include sand and gravel, limestone, and decorative stone.

Jan 1, 1992

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961

By Arnold C. Love

This report discusses current research by the U.S. Bureau of Mines on the effects of whole-body vibration (WBV) and shock on underground mobile equipment operators. The highlights of a comprehensive literature review of WBV, shock, and seating are presented. Factors discussed include health and physiological effects, comfort, performance, and fatigue. Vibration data were collected from shuttle cars and ramcars at several underground coal mines in Pennsylvania, Ohio, and Illinois. The data were formatted so that they could be used to drive the Bureau's motion platform, and to compare them with ANSI S3-1979, Guide for the Evaluation of Human Exposure to Whole-Body Vibration. Human subject testing in the Bureau's vibration research laboratory evaluated the effects of two different seat angles and of the presence or absence of vibration and of foam padding on heart rate, blood pressure, and subjective discomfort. Only vibration significantly increased heart rate and systolic and mean blood pressures. Vibration and a steel seat had a significant effect on subjective discomfort. The apparatus used for these tests and the experimental procedures are described in detail. Recommendations are made for additional research on the exposure of underground mining machine operators to WBV and shock.

Jan 1, 2010

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted the Bureau's Mount 'Weather Testing Adit,Mount Weather, The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Revelle, mining-engineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gavel valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

By E. T. Bowers

Pneumatic conveying of coal underground is not widely used in the United States, although it is becoming increasingly popular in Great Britain, the Federal Republic of Germany, and South Africa. The question of safety has been raised repeatedly: Will the system be prone to dust or gas explosions, and, if so, can it withstand such occurrences safely? The work reported here was done under a Bureau of Mines contract and deals with the safety aspects of pneumatic transport of underground coal, as well as the hazards inherent in more conventional haulage systems. Included are three designs for different applications of pneumatic haulage: off-loading a continuous-mining machine on a room- and-pillar section, vertical hoisting through a 1,200-ft shaft, and off-loading a tunnel-boring machine driving a 2,000-ft tunnel.

Jan 1, 1985

By Lincoln A. Stewart

"INTRODUCTION The First Supplemental National Defense Appropriation Act, approved August, 25,, 1941, authorized the Bureau of Mines to investigate sources of raw, material for western production and appropriated funds for that purpose. Numerous iron deposits and prospects in the Western States were investigated. Among those selected for more detailed investigation were tile Apache and Chodiski deposits in Arizona.The United States Geological Survey had examined these deposits in 1929 3/ and estimated that ""the quantity of minable ore reasonably to be expected in this locality will reach 10,000,000 long tons, but it will require prospecting by core drill to demonstrate this quantity with certainty"". C. H. Johnson, a mining engineer of the Bureau of Mines, made a preliminary examination in October 1941 and proposed exploration of the Apache deposit Canyon Creek.A trench sampling project was set up, and work at the Apache deposit commenced in November 1941. Mapping, trenching, and sampling of outcrops was completed in March 1942. Trenches were laid out at approximately 200-foot intervals for about 9,200 feet along the iron outcrop east of Canyon Creek, and channel samples were taken across the iron formation. The outcrop also was explored by trenching and sampling along a 1,900-foot outcrop on the west side of Canyon Creek.The first diamond-drilling campaign at Apache was initiated in May 1942 and continued to January 1943, when work was suspended owing to depletion of funds. Six holes spaced at approximately 500-foot intervals and, 500 feet back from the outcrop on the east side of Canyon Creek were drilled through the iron formation during this period.While this drilling was in progress, the Chediski deposit was mapped, trenched, and sampled. The trenches were spaced at intervals of approximately 800 feet along 10,000 feet of the iron-ore outcrop."

Jul 1, 1947

By Iain Finnie

This report is in three parts. The first part presents a review of theoretical models which have been developed to study removal operations for various types of materials. In the second part, a brief summary is given of coal cutting research. The majority of this work has been carried out in Britain using chisel type bits rather than the conical picks which are in general use in this country. However, a comparison of specific energies measured for conical picks in the laboratory and in the mine shows very encouraging correspondence. In the third part of the report, analytical models for coal cutting by picks are suggested. An extension of the British "tensile breakage" theory, developed for chisels, is given for picks. The role of crushing and cutting in coal removal is discussed as a theory which combines the two processes is shown to give reasonable predictions for specific energy requirements. Finally, directions in which the existing theory could be improved are presented and the need for further research is emphasized.

Jan 1, 1977

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

By Raja V. Ramani, Robert L. Frantz

"The House/Senate Joint Conference Committee has instructed the Bureau of Mines to have the Advisory Committee on Mining and Mineral Resources Research review on an annual and simultaneous basis each generic mineral technology research center (GMTC). In order to accomplish that review promptly and uniformly, committee members have revised and approved an in-depth questionnaire. That document formed the basis of their review. The information provided by that questionnaire was an important factor in their recommendations concerning the future direction of the program; a presentation was made at the last National Plan Update.The comprehensive nature of the questionnaire and the scope of the information contained therein make it an excellent retrospective of the Center. Having a clear vision of where the Center has been and knowing where it is now will help guide it into the future. It is felt that such a detailed view of the Center's facilities and research program will be of value to Center personnel and Advisory Committee members.Each aspect of the questionnaire has been examined, answered in detail, and documented throughly. With the completed questionnaire as a guide, this volume examines the research program, Center personnel presently active on GMTC projects, number of graduate degrees granted with GMTC support, GMTC publications, degree of individual interaction, technology transfer, the reference center, GMTC equipment and facilities, and any envisioned plans for future research. It is hoped that this volume will serve as a review of the years 1984-1988, the first four years of the Center's operation."

Aug 31, 1989

By J. D. Davis

The Bureau of Mines Coal Carbonization Laboratory has been interested for the past 20 years in the quality of coke in connection with the selection of coals for the manufacture of coke. The principal experimental. method of carbonization, whereby 100- to 200-pound charges are carbonized in sheet-steel cylindrical retorts with recovery and determination of the properties of coke, gas, and products, was developed in cooperation with the American Gas Association,4 5 and it is known as the BM-AGA method. Results of the investigations of 90 coals included in the BM-AGA Survey of the Carbonizing Prop¬erties of American Coals have been published; 6 and, in addition to these, about 200 coals have been carbonized over limited temperature ranges. Because coke from cylindrical retorts differs in shape from that made in rectangular ovens, the BM-AGA method has been criticized, although those who developed it have always believed that it served well as a means of measuring the relative strengths of cokes from different coals. It is recognized that no laboratory-method carbonization, even on a large twit, can yield results that exactly duplicate those obtained in commercial ovens and retorts. However, with the completion and satisfactory performance of an experimental vertical slot oven of 500-pound capacity at the University of Illinois Geological Survey Laboratory,' the opportunity to directly compare BM-AGA coke with coke made by two-sided heating became available and the necessary test apparatus was installed. The Bureau of Mines slot oven, which is similar to that designed by the University of Illinois Geological Survey, has been used to carbonize 11 coals (or blends) tested by the BM-AGA method. This report compares the results obtained by the two methods.

Jan 1, 1950

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1985 was $405.9 million, a slight decrease from the record high of 1984. With the exception of clays, output of most nonfuel minerals increased over that of 1984. Alabama was second in the Nation in production of crushed marble and bauxite; third in firre clay; fourth in masonry cement and kaolin; fifth in portland cement and lime; and sixth in ferroalloys and recovered sulfur, Alabama ranked 20th in the Nation in value of nonfuel minerals produced, but ranked 13th in value of industrial minerals. Valuewise, Alabama produced 2.4% of the Nation's industrial minerals.

Jan 1, 1987

By R. A. Cattell

The peacetime activities of the Bureau's petroleum and natural-gas program have been reoriented to serve the needs of a national-defense program. When the United Nations sent troops to Korea after the North Korean Army crossed the 38th parallel in the latter part of June 1950, the Bureau's coordinated national program on petroleum and natural gas, with each major project forming an essential member of its framework, was carefully reviewed by those in charge of the work. As a matter of fact, the era of normalcy in which the petroleum and natural-gas research of the Bureau of Mines prospered during the fiscal year 19502/ was no sedative to the need for alertness on a national-defense front. The program, although conducted along peacetime lines in general, was scanned critically and repeatedly during that period to see where - if the need should arise -the emphasis could be shifted from peace to defense or war. Judging from the experience of two wars, it would not be long before the Bureau would be asked to use its trained technical personnel in applying techniques already learned in peacetime research to the requirements of munition and fuel needs of national defense. Near the end of January 1951, petroleum and natural-gas engineers of the Bureau of Mines began a comprehensive study of reservoir conditions in the Canyon Reef fields of Scurry, Borden, and Kent Counties, Tex. This work was preceded by published analyses of crude oils from Scurry County as early as April 1950. Well-informed persons in industry have estimated that these fields hold reserves that will yield 3 to 6 billion barrels of stock-tank oil. Although generally accepted good operating practices have been followed, engineering tests have shown that the natural energy, except in some favorable parts of the reservoir, will not be adequate for obtaining a high percentage of recovery. Correct information regarding the extent and availability of this vast reservoir of hydrocarbons is therefore of great concern to the Petroleum Administration for Defense in carrying out its responsibilities under the Defense Production Act.

Jan 1, 1952

Studies of coal reserves have shown that the total augerable reserve base for the United States is estimated to be five billion tons under the current state of mining technology; the potential reserve base at 850-ft penetration is estimated at 20 billion tons. It is with the idea of improving coal recovery, a basic objective of Project Independence, that new concepts, such as modifications and improvements in current machines and development of ways to recover pillars left by current augering, are required. Unless recovery is improved, these potential reserves amount to lost coal.

Jan 1, 1975

The 53 countries that constituted Africa in 1992 accounted for a significant portion of total world output of a number of mineral commodities. However, the continent's total output for a number of major mineral commodities declined relative to the volume produced during 1991. (See tables 1 and 2.) The most conspicuous declines in mineral production from 1991 to 1992 were for cobalt and copper (declines of 28.6 % and 23.4 %, respectively), which could be partially attributed to mining and metal processing difficulties caused by political and economic disruptions in Zaire and for uranium (12 % drop), for which much of the continental production decline was ascribed to Namibian cutbacks in response to lower world prices. The severe regional drought also adversely affected the mineral industry in a number of sub-Saharan nations.

Jan 1, 1994

By D. Harrington

The record of fatalities from mine explosions in the United States during the past 3 years has been the best in the history of the mining industry. During these 3 fiscal years, mine explosions have resulted in an average of 4I0 deaths per year, as compared with an average of 153 deaths per year for the preceding; 5 years; an average of 542 deaths per year for the 3-year period 1907-09, inclusive, just before the organization of the U. S. Bureau of Mines; and a yearly average of 265 deaths per year for the 20-year period prior to 1929. This remarkable reduction in deaths from mine explosions demonstrates clearly that mine explosions can be controlled; in fact, they can be prevented when or if the mining people of the United States see fit to take the readily available precautions necessary to bring about this desirable objective. Several large coal-producing States, which in the past have had numerous disastrous explosions, have been free from such disasters for continuous periods of as much as 6 years or even longer. The bituminous mines of Pennsylvania, the largest coal-producing State, give a good example of what can be done to prevent explosions; this State has had only one major explosion (and it resulted in 7 fatalities) during the past 6 years, and no explosion occurred in the several hundred bituminous-coal mines of the State during the past fiscal year. This is a truly remarkable record when compared with past performance in any year in the operation of coal mines in Pennsylvania.

Jan 1, 1936