Search Documents

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By Charles L. Kimbell

The year 1977 generally was a year of growth in overall world mineral industry activity, although there were downturns in major elements of the world's iron and steel industries. The sharp upturns in market economy nation activities that were noted in 1976, following the reduced performance levels of 1975, were moderated, and in the centrally planned economy nations, overall mineral industry activity apparently continued to increase, but at a pace in keeping with that of 1916 rather than at the higher rates of the earlier 1976's. Noteworthy during the year, if only in a negative sense, was the inability of world powers to reach any significant agreement on issues relating to deep seabed mining. Interest from a commercial viewpoint centered around deposits or so-called manganese nodules. These materials, which indeed are chiefly manganese in terms of their content on a quantitative basis, really were of commercial interest primarily far their copper, nickel, and cobalt content. Participants at the Third United Nations Law of the Sea Conference looked into seabed mining rights, but reached no mutually agreeable decisions.

Jan 1, 1981

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By W. L. Cooley

Electrical accidents occurring in coal mines from 1975 through 1979 were categorized and analyzed. The data was searched for common electrical hazards, common activities on the part of those injured, and common negligent or careless behavior. The most common electrical hazard was abnormal arcs or sparks, the most common injured activity was handling energized trailing cables, and the most common careless behavior was failure to de-energize circuits before working on them. The accident data was combined with mine production statistics to form a normalized electrical accident rate. It was found that some mines have consistently more lost workdays per man-hour worked than do other mines. Bureau of Mines electrical safety research contract expenditures were reviewed to judge whether the research effort was directed to those areas which are related to the most accidents. In some cases it was not. A method was devised and utilized to estimate the relative cost to the mining industry to implement certain safety measures developed through Bureau research, and also to estimate the potential safety benefits. Some safety changes are recommended, others are not. MSHA regulations were reviewed for effectiveness in preventing electrical accidents, and suggestions were made for discontinuing, clarifying, or otherwise modifying the regulations.

Jan 1, 1981

By Charles L. Kimbell

In overall aggregate, the world's mineral industry in 1987 experienced a more satisfactory year than in 1986, at least insofar as its performance could be assessed from traditional statistical indicators. Production, trade and consumption seemingly advanced in the case of the majority of commodities, and prices for a number of commodities advanced. It was by no means certain, however, whether 1987 investment in mineral industry ventures would top the levels of 1986, when, in the case of petroleum industry investment expenditures there had been a sharp decline, this in contrast to evidences of a slight upturn in steel industry investment. World crude mineral output value was estimated at more than $1,084 billion, and the value added by minerals industry processing of this material probably raised the total value of the industry's production from primary materials to more than $2,600 billion constant 1983 dollars. Less easy too assess was the value of mineral commodities moving in international trade, but with a resurgence in oil prices from the 1986 levels, an increase above the 1986 $500 billion mark seemed assured. There are no comprehensive aggregate statistics on mineral consumption comparable to those on production and trade, but quantitative growth recorded for most major commodities suggested a favorable trend, particularly when coupled with a general (though by no means universal) upturn in unit prices.

Jan 1, 1989

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995

By E. A. Mevissen

With the ever increasing consumption of mineral commodities, the vital question is not whether sufficient mineral quantities will be available, but rather can the known existing low grade resources be mined economically. Conventional conveyor systems are being used in some open pit mines to decrease haulage costs. n an effort, to take this concept one stop further, this contract study examines the use of a high angle conveying system in an open pit mine. It identifies available high angle conveying equipment and examines the haulage and crushing costs associated with both a conventional truck and shovel mining operation and a high angle conveyor operation. These costs analyses were performed on a hypothetical copper, taconite and phosphate mine. Information was gathered from a series of high angle conveying equipment and open pit mining operations in the U.S. Volume I includes a detailed review of the state-of-the-art in high angle conveying concepts, the, hypothetical mine development, and the cost analyses. Volume II includes the appendices.

Jan 1, 1981

By Charles L. Kimbell

For the world mineral industry as a whole, the year 1981 was a period of continuation and, in some instances, an acceleration of negative trends extending back into 1980. Most available statistical data reflected stagnation or downturns in activity. Levels of production, trade, and consumption declined for a substantial number of leading mineral commodities, including, most notably, steel and petroleum. Investment, if not lower than in 1980, was evidently increasing at a more modest rate. Prices for major mineral commodities were generally lower, at least in terms of constant dollars, and in some cases even in terms of current dollars. Prospects of a major reversal of these patterns seemed dim. The mineral industry, however, was far from alone in this general downturn; most other elements of the national economies of the world's nations fared little better. General conditions of inflation, recession, and reduced industrial product consumption were reflected in most other sectors of the total economy. International political events continued to influence mineral output and flow but had less influence on overall levels of activities than on the geographic distribution of these activities. The Iran-Iraq war certainly played a role in reducing mineral industry activities in those nations, but the commodity most affected, petroleum, was available from other sources in sufficient quantity that, in the face of reduced demand, a substantial surplus developed.

Jan 1, 1983

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade. By the late 1990s, longwall mine output accounted for 40 percent of all underground output in the U.S., and today longwall mines account for approximately 50 percent of coal produced underground in the United States. A 53 percent increase in average shift production rates has occurred over the last fifteen years. This increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust provides an ongoing challenge for coal mine operators. The National Institute for Occupational Safety and Health (NIOSH) has completed a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources on the longwall section and to determine the relative effectiveness of the different control technologies in use today. Substantial reductions in dust levels were realized at sampling locations on the face when compared longwall surveys conduct in the 1990?s. This paper summarizes the results from the underground dust surveys and discusses current longwall dust control technology and operating practices.

Jan 1, 2010

By Donald E. Buck

In 1988, Albania's centrally planned economy continued to decline. The country's officially published yearend economic report did not contain concrete results such as the growth of national income or industrial output. 2 The shortfall for central budget earnings for 1988 amounted to 9% below the planned target. Losses in industry were attributed to poor management and organization, as well as to low technical standards and excessive consumption of fuels and raw materials. The construction, energy, and mining sectors of industry did not meet their annual production plans. As in 1987, within these sectors, the chromite and petroleum extracting and processing industries continued to lag in output. Both chromite and petroleum remained Albania's chief sources of foreign exchange; the production downturn of these commodities continued to negatively affect the country's foreign trade position, especially in view of constitutional prohibitions against using foreign credit to finance trade. The chief events in the minerals industry in 1988 included the construction startup of the first of four planned new concentrators at the Bulquize chromite mine, as well as the construction startup of new ferrochromium capacities at Elbasan. Also, the copper mining industry reported the completion of facility expansion at the Perlat mine in the Mid-rite district. Albania began new facility construction at the Dinamo heavy-equipment enterprise at Tirana to maximize self-sufficiency in mining equipment production. Upon completion, the new factory would double the out-put of mining equipment at the enterprise and would introduce new designs for electric trucks and pneumatic drills for the mining industry. The new facility would also increase the production of new machinery and equipment for the country's beneficiation plants.

Jan 1, 1990

By Paul M. Ambrose

THE ABRASIVES INDUSTRY throughout the world enjoyed a profitable year. With the exception of tripoli, the quantity of each kind of abrasive produced in the United States was greater than for any of the past 5 years and value of each was greater than for many years. Production of silicon carbide both in the United States and in Canada was the largest since 1960. Abrasive machining, which offers great potential for the increased Use of aluminum oxide, contributed to increased industrial productivity. Diamonds from the sea off the coast of South-West Africa attracted wide interest. Much of the production from this source has been gem diamond, and there is little likelihood of significant quantities of industrial diamond from that source. Manufactured diamond from all free-world sources was sold in the United States in 1964.

Jan 1, 1965

Overexposure to noise is a widespread, serious health hazard in the mining industry, and causes hearing losses to a large percentage of the mining population. Recognizing this fact, the Bureau has a major on-going research effort to address this problem area. These proceedings include an overview of the Bureau noise control program and summarize nine selected noise control research programs.

Jan 1, 1984

By F. A. Rutledge, B. S. Webber, J. M. Moss

"INTRODUCTION The United States, with its vast resources of relatively low-grade zinc been the world's leading producer of zinc -metal for many years. The expanded zinc production during the period, 1939-44, inclusive, was induced by favorable premium prices and has depleted the known ore reserves in the United States. The 1943-44 rate of zinc production cannot long be maintained in the United States, especially if premium prices are removed. Domestic zinc reserves, have been depleted to such an extent that it is doubtful if our mines will again be able to completely and continually fulfill the needs of this country.The Bureau of Mines, anticipating a postwar consumer demand for 550,000 to 750,000 tons of slab zinc and an additional 100,000 tons for use in paints and chemicals, sent two engineers to Sedanka Island in July 1945 to investi¬gate the deposits near Biorka Harbor.ACKNOWLEDGMENTIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion the Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By J. W. Thompson

LIMESTONE DEPOSITS. Limestone deposits that have not been demonstrated to be of such quality as to give them any substantial value over other limestone deposits of the same region, are not regarded as minerals. Gray Trust Co., In re, 47 Land Decisions 18, p. 20. OIL AS A MINERAL. Oil is a mineral substance and its removal will greatly impair the value of the land from which it is removed. Texas & Pacific Coal & Oil Co. v. Howard. Southwestern 735, p. 737. Tex. Clv. App. 212 OIL AND GAS AS MINERALS OWNERSHIP. Oil and gas are minerals and so long as they remain in place they belong to the owner of the land under which they are found and such owner has the right to explore for the oil and gas on or under his land and when found to remove and possess the same. Kimbley v. Luckey, Okla. - 179 Pacific 928, p. 831. OWNERSHIP OF MINERALS LACHES NO BAR. The owner of minerals in land can not be barred by laches for failing to assert his ownership where his title had not been ques- tioned and his right invaded. No lapse of time bars one's right to property and it is only in case his right has been invaded that it can be barred by laches.

Jan 1, 1920

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertained by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertainedd by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By Stanley P. Jacobsen

Samples of fine coal refuse were obtained from 11 coal preparation plants throughout the United States. These samples were characterized by ash analysis, particle size, and mineral composition. From the characterization, geographical locations, and the dewatering equipment being used by the plants, five sites were selected for obtaining bulk fine refuse samples. The selected coal preparation plants were using for final dewatering thickeners followed by: a vacuum disc filter, a filter press, a belt press filter, a centrifuge, and a settling pond. None were using thermal drying. The moisture content of the final cake varied from approximately 23% to 50% depending upon the feed material, flocculant addition, and the type of equipment. The filter press gave the lowest moisture content followed by a belt press and then either a centrifuge or vacuum filter. The centrifuge products were all dried to an approximate 5% moisture in a thermal dryer.

Jan 1, 1981