Search Documents

By D. R. Corson

The Bureau of Mines instrumented an operating stope in a deep vein mine to determine the amount of wall closure and the magnitude of loads imposed on a backfilled stope. Hydraulic pressure cells used to monitor pressures in the fill) with bolt closure points to measure vein-wall movement and the procedure for their installation) are described) and the results of the laboratory calibration analysis of the reliability of these cells are given. An attempt to monitor density and moisture changes in the backfill with a nuclear density-moisture device was only partly successful) owing to either deformation of access tubing or relative displacements of the vertical vein walls relative to the emplaced tubes. Data from the instrumentation indicate vein-wall closure in excess of 20 inches and pressures within the fill approaching 600 psi. Analysis) incorporating field data with results of laboratory tests of the compressibility of timber and tests defining the constrained moduli of the fill) points out the limited restraint to vein closure offered by timber sets. Ground movement induced by mining activity could be more effectively con-trolled by the use of densely compacted backfill.

Jan 1, 1967

A preliminary study was conducted by the Bureau of Mines to determine the effect of humidity on salt mine airborne dust levels. Results showed less dust where the humidity was elevated. Dust reductions appeared to be dependent on the equilibrium between humidity and salt.

Jan 1, 1980

By Mirza A. Beg

The Piedmont physiographic province of east-central Alabama lies in a humid subtropical climatic zone. Such an area with mature land forms underlain by rocks rich in feldspars provides conditions condusive to development of gibbsite, a major source of alumina; a raw material for which the United States relies on foreign suppliers for 85 percent of its needs. Gibbsite occurs in the northern and inner sections of the Piedmont Province of Alabama in Coosa, Clay, Randolph, Chambers, Elmore, Tallapoosa and Lee Counties in soils and saprolite derived from amphibolites, granites, feldspathic hornblende gneiss and other gneissic rocks. The major occurrences of gibbsite are in areas underlain by hornblende gneiss in Chambers and Randolph Counties. This region provides the proper physiographic and mineralogical setting for large areas containing up to 25 percent of saprolitic gibbsite. These areas provide potential sources of alumina that could be used to meet the United States future needs. Narrow zones and pockets rich in gibbsite also occur in soil and saprolite derived from areally restricted feldspar rich zones of narrow linear amphibolites in the inner Piedmont and feldspathic zones in various granites distributed throughout the Piedmont.

Jan 1, 1982

By J. R. Thoenen, B. H. Clemmons, A. H. Reed

"INTRODUCTION AND SUMMARYOverall red-ore reserves in the Birmingham, Ala., area were estimated in 1910 by E. F. Burchard 4/. Since then mining has progressed into areas classed by Burchard as ""unavailable for exploitation"" under conditions existing at that time. This is understandable when it is considered that red iron ore was valued at $1.19 a gross ton at the mine in Birmingham in 19102/ and by 1948 had risen 300 percent; 6/ that skips had replaced cars in slope haulage; that mechanical loading and rubber-tired haulage had replaced hand loading and mule or locomotive haulage; and that other more efficient mining methods had been introduced. Intensive study during the intervening 40 years has been given to ways and means for upgrading the low-grade ores in the area and combining or blending them with raw red and brown ores for improved blast-furnace feed.It is reasonable to expect that future progress in mining efficiency and increased knowledge of the beneficiation characteristics of marginal ores will permit extraction of red-iron minerals now considered uneconomic.The Bureau of Mines has undertaken to restudy iron-ore reserves of the Birmingham area to determine what tonnage and grades of mineral are present; what is necessary to make them amenable to mining; what further advancement is possible in beneficia¬tion methods; and where increased production may be obtained in the area if and when required. This study has been underway for the past 2 years, but research into the beneficiation of marginal ores has been in progress at the Southern Experiment Station for the past 30 years. Many results of that research have been adopted in commercial practice in the area. Other results have not been published but are pre¬sented here in condensed form as an important factor in assessing marginal deposits with respect to their importance as ore reserves.An interim discussion of the salient features of past history and progress, as well as the data developed during the years of research in beneficiation at this station and the present field investigation, will make for a better understanding of the present position as well as be useful in evaluating future potentialities. Discussion in this paper is confined to the main Birmingham Basin area, which contains the largest concentration of hematite ores in the district."

Jul 1, 1953

By Alexander May

The Bureau of Mines conducted studies to determine if phosphogypsum, a waste material from the processing of phosphate rock, contains hazardous toxic materials as defined by the Environmental Protection Agency (EPA) and whether leaching of these toxic materials and radium may occur. Samples of the phosphogypsum stockpiled material were evaluated using the EPA extraction procedure, atomic absorption, neutron activation, x-ray diffraction, and chemical and physical means. Radiological tests performed used both the germanium-lithium and emanation methods. The data show that the phosphogypsum stockpiles are not hazardous toxic waste as defined by EPA criteria. Trace elements and radium are not leached from the phosphogypsum stockpiles. Absorption of trace elements and radium by phosphogypsum is the major reason for their not being leached. The standard error of measurement of radium concentrations was 4.7 pCi/g.

Jan 1, 1983

By Eric E. Cather

Approximately 270,000 cu yd (20[0],000 cu m) of inferred subeconomic auriferous gravel resources were estimated in three Tertiary deposits in the Polk Springs study area (fig. 1 and table 1). These resources are exposed between tuff-breccia and lava flows of the Pliocene Tuscan Formation and Paleozoic or Mesozoic metamorphic rocks which suggests that although no deposits were identified in the other RARE II areas, they may be concealed beneath the Tuscan Formation. Difficulty in choosing drilling targets will make the likelihood of resource discoveries small. The development and production of these deposits would also be prohibitive under current economic conditions due to the thick covering of volcanic rocks. Recent stream gravels of Deer Creek in the Polk Springs study area contain enough gold to attract gold hobbyists; however, the stream gravels do not have sufficient volume to be considered a resource. Potential exists for additional auriferous gravels near the Occidental Mine in the Polk Springs RARE II area.

Jan 1, 1983

By James C. Fowler

The design and field testing of a seismic miner detection and location system arc described. This work was carried out over a period of three years. The first two and one-half years were sponsored by Continental Oil Company, while the last period of tests were done as the first part of a one-year contract with the U.S. Bureau of Mines. Laboratory and field experimentation in three different nines under simulated emergency conditions have led to three important results: (1) Taps on roof bolts with normally available objects can usually be detected up to horizontal distances of 1,000 ft. (2) The origin of the tans can be located by on-site processing with a small computer. (3) Some predetermination of the approximate location is necessary for a quick and successful rescue. This report also includes preliminary specifications an,d cost guidelines for construction of a transportable field system capable of matching the performance characteristics of the one used during the field tests.

Jan 1, 1973

By F. Matanzo

[Nine wire rope terminations were pull tested and fatigue tested to destruction to measure the termination efficiency and relative fatigue life. The terminations were selected on the basis off mine site visits and the specimen were assembled in a manner similar to industrial slings. To measure a termination's sensitivity to poor workmanship, both standard and modified assembly specimen were tested. Lang and Regular construction of the 6x19 and 6x37 class wire ropes were used in diameters of 13 mm (1/2 in.), 19 mm (3/4 in.), 25 mm (1 in.), 38 mm (1 1/2 in.), and 51 mm (2 in.). In static pull tests rope class, construction, and diameter interacted with the termination to influence the efficiency of the termination. In axial fatigue tests using only the 6x19 class rope, the effect of rope construction was negligible since failure was primarily dependent on the termination type. The Swaged Socket, a termination requiring a high capacity hydraulic press, gave the best overall performance in terms of efficiency and fatigue life. The short body length of the Zinc Poured Socket (RR-S-550) was attributed with the short fatigue life of this termination. The use of thermosetting resins as a replacement for zinc was demonstrated successfully for some socket designs. The fatigue life of the termination, expressed as a percentage of the fatigue life of the wire rope, was shown to be a guide for the retirement of the wire in these applications where the wiry' rope is primarily in axial loading.]

Jan 1, 1978

By C. B. Manula

This report is volume 4 of at. eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment: The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Roof Support subsystem of the Master Design Simulator. This model is based on popular roof support practices for different geological environments with related restrictions imposed by the Coal Mine Health and Safety Act of 1969. From geological sections, the model determines the anchor horizon for roof bolts and the density of roof support necessary. The roof support subsystem is tied to both the geology and reserves subsystem and the production subsystem of the Master Design Simulator, but can also operate as a free standing model. Several case studies are presented showing the application of the model. A detailed user's manual, including a program listing, is presented in the appendices.

Jan 1, 1974

By Robert L. Lagace

This final report documents the work dune by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982

By D. E. Van Dillen

Three-dimensional structural analyses of three instrumented areas of a deep, longwall coal mine have been performed using the finite element code BMINES. The three Instrumented areas include two single-entry portions and one double-entry portion of the Sunnyside No. 1 Mine, Sunnyside, Utah. The finite element models simulated the sequence of excavation in each test area: the advance of the entry, installation of structural supports, retreat of the longwall, caving behind the longwall, and accumulation and loading of the gob. The structural supports considered in these finite element models include rock bolts, wood cribs, concrete cribs, steel arch sets, and chocks. Mechanical simulation of the geologic environment is achieved through elastic/ perfectly plastic material models employing anisotropy to represent finely layered regions of the medium. The results of these calculations are com-pared with the instrumentation readings from the mine. These measurements include closures, crib loads, rock-bolt forces, and stress growth.

Jan 1, 1978

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By D. Bienstock

To develop a rugged catalyst capable of withstanding hydraulic attrition resulting from the oil-circulation process for synthesizing liquid fuels, use of an iron catalyst containing an active coating surrounding an inert solid core of metal was investigated. This massive-iron catalyst in the form of steel shot and lathe turnings was activated by partial oxidation with steam at 600° C, impregnated with alkali, and reduced with hydrogen at 450° 6. The massive-iron catalysts were resistant to oxidation and spalling, and a 6-month catalyst life was attained. Higher operating temperatures could be employed than with fused iron oxide catalysts, resulting in greater gasoline yields. Because the lathe turnings pack with void volumes of 70 to 90 percent, it has become possible to employ a fixed bed without the danger of cementation that occurs with fused iron oxides.

Jan 1, 1963

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By Charles E. Glass

The purpose of this report is to demonstrate the flexibility of rte sensing techniques for providing data with which to implement mined-lands reclamation in an efficient and cost-effective manner. An operational program is presented for using satellite remote sensing data, collateral data, and automated image analysis to provide: 1) an inventory of coal and copper mines and mine waste in Arizona, 2) techniques for periodic monitoring of mining areas using multitemporal classification and image prediction techniques, and 3) delineation of high priority areas for future reclamation and current land-use planning of Arizona mining areas based on environmental hazards indices computed using classified scenes and collateral data.

Jan 1, 1980

By Steven K. Ruggieri

This report describes the operation and maintenance of the Mobile Inert Gas Generator for use in the Remote Sealing System for fighting underground coal mine fires. Seals are emplaced in mine passageways between the fire zone and the rest of the mine isolating the fire zone from the mine. The seals consist of fly ash that has been pneumatically conveyed via inert gas through a borehole connecting the surface and the passageway, Inert gas is used as the fly ash seal transport medium (instead of fresh air) since the introduction of large volumes of fresh air in the vicinity of the fire zone would be undesirable. The inert gas generation equipment is mounted on two flatbed trailers, the "hot" trailer and the "cold" trailer. The hot trailer contains the combustion and cooling equipment. The cold trailer contains the moisture removal and compression equipment necessary to convey the fly ash. The system is self-sufficient and requires only fuel and fly ash deliveries. The Inert Gas Generator has been thoroughly performance tested and has been operated in the field for approximately 200 hr. The system was employed in the demonstration of the entire Remote Mine Sealing System at the Jenney Mine in the Fall of 1978. The system is currently available for fighting any future underground coal mine fires.

Jan 1, 1980

By Jennifer A. Slatnick

Chlorofluorocarbons (CFC's), once universally accepted as ideal compounds for use in cooling and refrigeration, in foam production, and in cleaning electronic components, are being phased out and eventually banned under extensive international agreements because the chlorine in CFC's is thought to deplete the Earth's ozone layer. The industry has responded with the introduction of alternatives in the form of hydrofluorocarbons (HFC's), which contain no chlorine, and with hydrochlorofluorocarbons (HCFC's), which fill an intermediate gap in the replacement of CFC's. As a result of the elimination of chlorine in the HFC's and the reduction of it in the HCFC's, these alternatives contain more fluorine than the CFC's do. Other nonfluorocarbon substitutes, known as not-in-kind alternatives, contain no fluorine at all. As a result, the fluorspar mining industry, which is the source of fluorine in fluorocarbons through intermediate hydrofluoric acid, is being affected. Concern for this impact has led the U.S. Bureau of Mines to employ its capabilities to analyze various scenarios in the evolution of CFC replacements and substitutes to determine their effect on fluorspar mining. This report utilizes a network flow model to examine the effects of proposed replacements for CFC's, in terms of fluorine content, on fluorspar operations worldwide and on hydrofluoric acid plants in North America and Europe.

Jan 1, 1994

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973