Search Documents

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By Earl C. Hutchison, Wade C. Hutchison

To effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre and post blast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By Tamara Wiseman, David Stewart

"A Quarry located in Georgia is a green-field site established in 2011. The quarry lies in the eastern part of the Georgia Piedmont area. It is within a distinctive, northeast-trending belt of relatively high-rank metamorphic rocks known as the Kiokee Belt, a poorly mapped sequence of units that largely consists ofamphibolite and various schists and gneiss that are host for relatively young granite bodies andassociated pegmatite and aplite dikes."

Jan 1, 2017

By N Gkikizas-Lampropoulis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper interprets previous experimental information on the effect of delay on fragmentation with the aid of some new experimental observations of the time of detachment of the free face of the blast as well as results of numerical modelling. It was shown that detachment of the burden occurs at delays shorter than the one which produced optimum fragmentation in the experiments, suggesting some fragmentation improvement due to gas action. In addition, at the spacing to burden ratio of the experiments, the damage zone from an earlier detonating charge extends the distance to the neighboring charge, essentially affecting the burden of some of the holes of the blast, at detonation time. Computer modelling demonstrated that increased spacing results is less overlap of stress induced damage zones meaning that there is less influence of delay on stress wave induced fragmentation. It was also shown that simultaneous initiation results in less back break, while increased back break may result even with short delay times.

Jan 1, 2016

By Joe Sr Strobbe

In 1933 the Cobre Mining Company re-opened the 32-year-old UV Industry Mine, which is located in a scenic canyon near Silver City, New Mexico. The site location is shown in Figure 1. Current mineral extractions are copper and magnetite; both extractions similar to those mined many years ago. Copper is extracted from chalcopyrite imbedded in the host rock of massive limestone deposits and magnetite, an iron ore, is a by-product of the same extraction process.

Jan 1, 1998

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Callie Covert

This paper describes the application and results of a more efficient method of breaking boulders using dynamite and water. This method is being used for the disposal of boulders that result from pinnacle and cap rock remaining after blasting on highways and job sites. This method is a faster and less expensive use of dynamite to reduce oversized boulders than the conventional rock hammer. The problem with excessive fly rock has been substantially reduced when using this technique over traditional methods.

Jan 1, 2001

In this paper, the author points out the need to beware of simple time correlations as proof of cause and effect when comparing building cracks and blasting operations. There is a need to be aware of the many other causes besides blasting which affect buildings. Some of these have histories of cyclic behavior; others have a long-term increasing effect on aging and deterioration, often with poorly defined time histories. Many are so strongly site specific that generic relationships are difficult to quantify.

Jan 1, 1981

By Robert J. Nothnagle, Kristen Franz Begor, Rodney W. Sutch

Recovery of contaminated groundwater in a fractured bedrock system presents some unique problems. Typically, the most common problem occurs from the inability to adequately characterize the discrete fractures through which contaminants may be migrating. Without adequate characterization, difficulties arise in properly positioning recovery wells and verifying the performance of the system. To overcome these difficulties at a site in Upstate New York, an innovative approach was developed involving the creation of an artificial fracture zone through controlled blasting to intercept contaminated groundwater flow.

Jan 1, 1988

By Jose A. Sanchidrián, Ricardo Castedo, Pablo Segarra, Juan Navarro

A study conducted at a mine site that used traditional field surveying and physical hole spot markings bench marked their combined drill and blast performance. The analysis of the operational expenditure (OPEX) improvement determined there were many measurable cost improvements. A primary factor that most operations have to deal with is over drilling of holes. This alone impacts the cost due to nonproductive labor allocations, excessive explosive costs, increased drill tool costs, increased drilling costs and has an impact on the downstream operation cost such as digging the shot material. Other related investigations also show a downstream impact of poor fragmentation on digging payload tonnes, cycle times, haulage payload tonnes, time to load a truck and the number of passes to load the tuck. The intent of this presentation is to draw attention to aspects of mining we understand but may be missing the big picture effects, such as the ability to reduce the operational expenditures consistently to impact the bottom line. The target audience is across the board from owner operators, drill and blast contractors to blasting contractors. Everyone can benefit from these improvements.

Jan 1, 2019

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By Paul Schmiesing, Matt Higgins

Central Oregon is a fast growing resort community centered in Bend, Oregon. Bend is bordered by the Cascade Mountains to the west and the high dessert to the east. Central Oregon is blanketed with lava rock with little topsoil. Ditch blasting is a staple in the area. Almost all utilities excavation (gas lines, sewer lines, water lines, and electrical lines) requires blasting. There is also a considerable amount of blasting required for site excavations and drywells. On average, there are over 500 blasts per year in Bend alone. All of this blasting is done using small holes, generally 2.5 inches in diameter. Typical ditches will have 200 holes, between 2-3 rows wide, with an average depth of 8 feet, and on 36 inch centers. Almost all shots are dry. Successful blasting requires careful control of drilling and loading. The vesicular basalt contains numerous lava tubes and caves making drilling and loading difficult. The rock conditions vary greatly from one side of town to the other requiring different powder factors and different scale of distances for vibration control. Caret%1 calculations of vibration predictions and use of site-specific seismic info is necessary. Marry shots will require deck loading and careful timing to ensure one-charge per delay. It is an every day occurrence to be blasting near residential and commercial structures or high pressure gas lines. Many times ditch blasting will incorporate excavation blasting. The different hole patterns used for the ditches and the excavation shots presents challenging timing sequences.

Jan 1, 2000

By William R. Adamson

This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

Feb 1, 2020

By William Adamson

Precise and data driven methods of predicting and modelling blast induced vibration intensity are created and applied under field conditions on a routine basis today. These models are fed with controlled field measurements of vibration pulses generated by controlled charges under known geometric conditions. With such models blasting and geomechanical engineers can estimate vibration intensity at established critical points in mine bench geometry (surface mining) as well as within semi-permanent crown and rib pillars (in underground mining).Damage to bench walls and destabilization of large-scale geomechanical structures can be partially attributed to high intensity blast induced stresses on the rock mass and structures that define important features such as safety catch berms and haul roads. In the underground environment, weakening of critical pillars in block caving or Long Hole Open Stoping(LHOS) operations may lead to ore sterilisation. Blast vibration intensity can be linked with physical alteration in critical rock mass volumes within themine. Often the potential for vibration damage is estimated by the calculation of a critical value of vibration intensity, derived from a consideration of laboratory measured rock matrix properties. Efforts to confirm the accuracy of these estimates of critical vibration level include post blast excavation photography as well as the visual examination of rock mass, pre-and post-blast, using video camera observation of the walls of purpose drilled observation holes. These methods clearly indicate a change in fracture state due to the blast induced vibration, however further modelling of geomechanical stability will benefit if seismic measurement data can be interpreted in terms of geomechanically relevant strength parameters. This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

By Matias Suarez, Diego Zenteno

This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002).

Feb 1, 2020

By John W. Kopp

The U. S. Bureau of Mines investigated flyrock and burden movement from blasting at several limestone and basalt quarries in the upper midwest. Blasts have been studied at 14 different sites using high-speed cinematography. Blasting was accomplished in 75- and 150-mmdiameter holes using a variety of explosives. Films from each blast were analyzed to show burden velocities, observed flyrock distance, and direction of throw in relation to the shot layout. This technique, in some cases, allowed determining point of origin and cause of the flyrock as well as the flyrock range.

Jan 1, 1994

By Cam Grundstrom

The Ok Tedi Mine is a large open pit copper and gold mine located in a remote section of the Western Province, Papua New Guinea, with an annual rainfall of over 10 metres. Ok Tedi mines an average of 205,000 tonnes per day. A strong working co-operation between the mine operator (Ok Tedi Mining Limited) and the explosives contractor (ICI Explosives Asia / Pacific) has led to progressive development of bulk emulsion formulations to meet site-specific needs, continued improvement to blasting applications, and competency based training programs for the national blast crew.

Jan 1, 1997

By Ed Jr Smith, Calvin J. Konya

The purpose of this paper is to describe the case history of a blasting project conducted jointly by Precision Blasting Services and Cherokee Explosives. It is the intent of the authors to show how blasting could be done in controlled fashion near very expensive computer controlled machinery. The job was done in minimal time with no complaints or allegations of damage in spite of the fact that blasting was conducted within five feet of the equipment and with the 32 acre plant fully operational, with machine operators working within 10 feet of the blasting site.

Jan 1, 1986