Search Documents

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson's ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014

By E. Lee

Cone crushers are widely used within the mining and aggregate industries for the size reduction of minerals, ores, and rock materials. In mining applications for example, the product from cone crushers is often fed to HPGRs or directly to mills in the subsequent grinding circuit. An improved cone crusher performance can therefore result in an overall improved and more efficient comminution process. The objective of this paper is to systematically study a number of different ways of applying compressive crushing. By mathematically modelling these different crushing concepts and then theoretically optimizing crushing sequences accordingly, each concept can be studied and evaluated. In addition, aspects concerning whether or not the results are mechanically or practically achievable are considered. This study thus explores the advantages and disadvantages of different crushing concepts. In this paper, four different theoretical crushing concepts are presented and studied. The results show that in terms of interparticle crushing, optimal crushing sequences with varying compression ratios can be replaced by easier implemented series of constant compressions without significant deterioration. It is also shown that that considerably better performance is obtained for crushing sequences with both breakage modes. The subsequent comparison between such concepts indicates that different approaches can achieve the same results, and that the different concepts are comparable. It is further concluded that interparticle crushing should be kept to a minimum if fines generation or energy consumption is to be minimized, and that each of the studied concepts presents different challenges for implementation. Keywords: compressive crushing, cone crusher, optimization, modeling, crushing concept

Sep 1, 2012

By Lala Zhao, Yuemin Zhao, Guangyuan Xie, Chusheng Liu, Chenlong Duan

"Screening is an important means of size classification used on granular or particulate materials. The vibrating modes of screen separator have a great effect on the screening process. Elliptical vibration mode is a complex motion mode which gets the common characteristics of both linear and circular vibration modes. However, the fundamental motion and screen penetration of the particles on the elliptically vibrating screen deck are still poorly understood. A numerical study of the motion of particulates flow along an elliptically vibrating screen deck is presented by means of a three dimensional Discrete Element Method (3D-DEM). The motion characteristic of the particle flow is analyzed at a particle scale. The effects of vibration amplitude, throwing index, vibration direction angle and screen deck inclination angle on the screening process are discussed. The results show that the particles average velocity increases linearly with the increase of vibration amplitude, throwing index and screen deck inclination angle, but decreases linearly with the increase of vibration direction angle. The screening efficiency is highest when the vibration amplitude, throwing index, vibration direction angle and screen deck inclination angle are 4.5 mm, 3.3, 40° and 6°, respectively. This work is helpful for developing a deep understanding of particle motion on the elliptically vibrating screen and for optimizing screen separator designs."

Jan 1, 2014

By J-P Franzidis, P. O. Gyebi

"Coal-water mixtures (CWM) of concentrated fine coal may be transported in pipelines but this is influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. The objectives of this study are to investigate the importance of surface charge, solids concentration and dispersant addition on the rheology and stability of a fine Witbank coal-water mixture (<75 m). Zeta potential, rheology and stability were measured with a Malvern Zetasizer, a AR1500EA rheometer and a static rod penetration test, respectively. Sendep 30D, Sendep 30F and Norilose 8058, all supplied by Senmin International, were used as dispersants, at dosages of between 0.1 to 0.5% dry coal (w/w). Solids concentration was varied from 10 to 58% (w/w). The zeta potential was found to be positive at low pH and decreased sharply with increasing pH to a minimum of -50 mV at pH 10. The zeta potential decreased with increasing dispersant concentration for all dispersants. The lowest zeta potential of -63 mV was obtained for Norilose 8058 at a dosage of 0.3%. CWM rheology was Newtonian at lower solids concentrations but became non-Newtonian at solids concentrations over 40% (w/w), with an initial yield stress and pseudo plastic behavior. The yield stress decreased sharply with increasing dispersant concentration for all dispersants. The lowest yield stress was obtained for Norilose 8058. The addition of dispersants resulted in significant improvements in stability. A penetration ratio of over 70% was obtained for Norilose 8058 after 10 days. In summary, the addition of dispersants resulted in a decrease in the zeta potential which increased the electrostatic repulsive forces between particles, thus improving both CWM rheology and static stability.INTRODUCTION Coal Water Mixtures South Africa’s energy economy depends heavily on coal. It accounts for about 70% of primary energy consumption, 93% of electricity generation and 30% of liquid petroleum fuels (Eberhard, 2011). The transportation of coal to export markets and power generation stations is a problem in the South African coal industry due to ageing and inefficient rail infrastructure. This problem is intensified by the long distance of coal haulage, delays in the time required to load and unload wagons, and environmental challenges related to air pollution and water contamination. Fine coal may be transported more efficiently and economically in a pipeline as a highly concentrated coal water mixture (CWM). Typically a fine coal CWM will contain 60-75% coal, 25-40% water and nearly 1% of dispersing additives (Atesok et al., 2005; Dincer et al., 2003). However, the transport of CWMs in pipelines is strongly influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. These quantities are affected by the coal composition/mineralogy, solids concentration, particle size and size distribution, particle shape, inter-particle forces and dispersant type and dosage (Laskowski, 2001)."

Jan 1, 2018

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By Adam Jordens, Olga Kuzmina, Christopher Marion, Kristian Waters

"In order to meet the growing demand for non-Chinese rare earth suppliers many new rare earth (RE) mineral deposits are currently under development, however these deposits typically include many minerals for which there is little processing information available. One of these deposits is the Nechalacho deposit located in the North West Territories of Canada. This deposit contains multiple RE minerals including bastnäsite, zircon, fergusonite, allanite and monazite. The work presented here investigates the use of different classes of flotation collectors (carboxylic acids, hydroxamic acids, phosphoric acids) typically used in RE mineral flotation to float the Nechalacho ore directly. Flotation tests are also conducted as the final step in a beneficiation process incorporating centrifugal gravity concentration and magnetic separation. This combination of centrifugal gravity concentration and magnetic separation rejects low specific gravity gangue minerals such as K-feldspar and plagioclase and concentrates high specific gravity minerals such as magnetite and hematite. The removal of low specific gravity gangue helps to improve flotation and the removal of ferromagnetic iron oxides is important prior to flotation using certain chelating collectors."

Jan 1, 2014

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Chuanyao Sun, Longli Liu, Fayu He, Guiye Wu

Utilizing thioglycolic acid (TGA) as a template and using structure-guided design, a molecular modelling approach has been used to design and screen appropriate dispersant for chalcopyrite. A series of organic dispersants based on a TGA substitution with hydroxyl and amino and sulfonic functional groups have been examined on chalcopyrite surface. 20 organic depressors of chalcopyrite have been investigated to study the quantitative structure-activity relationship (QSAR) of chalcopyrite depressors. For the chalcopyrite surface, depressor containing carboxyl and sulfonic group is generally stronger than the depressor containing hydroxyl group. Increasing the number of hydrophilic group can effectively enhance the inhibition. Increasing the number of Solidophilic group does not necessarily lead to enhanced inhibition ability; steric factor is one of the important factors to affect the interaction. Extension alkyl carbon chain length cannot enhance the interaction of depressors. Isomers principle as well as applies to the chalcopyrite depressor molecular design. Flotation verification tests further confirmes the accuracy of the molecular simulation. Through the Computer Aided Molecular Design (CAMD) technology, we can save enormous time and resources to design novel surfactants. This research and application will play a great significance role in sulfide flotation.

Jan 1, 2014

By Trevor Saldanha, Stephen Grano

A key uncertainty in flotation modelling is determining, a priori, the proportion of each mineral which will develop a certain rate constant for different feeds of variable liberation and hydrophobicity. First and foremost is the ability to predict the proportion of minerals that will not be recovered, even at very long flotation times, and which therefore report to the tailing stream as the non-floatable fraction (i.e., having a zero rate constant). Recent empirical evidence has shown there are at least two factors which contribute to heterogeneity in flotation rates and, in particular, the appearance of a non-floatable fraction - heterogeneity in the distribution of adsorbed collector amount on a particle-by-particle basis, even for the same liberated mineral in the same size fraction, and the existence of a critical contact angle below which the bubble-particle union is unstable. In this paper, inferred measures of the critical contact angle for liberated particles are compared with stability model calculations. This has demonstrated that the dependency of the critical contact angle with particle size and mineral specific gravity are explicable by bubble-particle stability considerations. This argument is further extended to the flotation behaviour of composite particles, as a function of liberation class, in which the wetting perimeter of the attached bubble on the composite particle surface is constrained by the presence of a surrounding hydrophilic domain for the case of simple binary composites. Reasons for the different flotation behaviour of composite particles having different textures, as noted in the literature, are also discussed in terms of the stability of the bubble-particle union.

Jan 1, 2014

By Hamid-Reza Manouchehri

"Sustainability calls for maintenance, rational use and enhancement of natural resources as well as balance consideration of ecology, economy, and social justice. The challenges in mining industry call for a sustained global effort using the leverage of available technologies and emerging new technologies. The industry uses significant amount of energy with the highest portion in comminution. To conserve energy, attempts have been made to improve the efficiency of the conventional crushing and grinding equipment. Nevertheless, the new and energy efficient comminution technologies are favorable through a longer term strategy. Since crushers are more energy efficient than mills, it is logic to conduct part of milling, in the crushing stage. After years of research and development, Sandvik introduces a new crushing technology, VibroconeTM, to change traditional crushing concepts. The new crushing device is able to crush and grind particles with a higher reduction ratio, more than two fold, than that of conventional crushers. By implementation of the new technology, a suitable feed size for milling can be provided to conserve energy as well as media and liner consumption, to reduce milling circulating load or increase mill capacity. There are other benefits associated with this machine, one of them being providing a higher surface area. This paper discusses the performance of the machine and its applications for comminuting different ores."

Jan 1, 2014

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By Kunihiko Yamaguchi, Gjergj Dodbiba, Toyohisa Fujita

Usually magnetic separation is performed to separate ferromagnetic, paramagnetic and diamagnetic particles by controlling magnetic field strength. In this research the wet high gradient magnetic separation at various kinds of magnetization of medium has been investigated to separate different kinds of magnetization of paramagnetic mineral particles from each other. Most of week paramagnetic particles are captured at high magnetic field using superconducting magnet. If the magnetization of fluid is larger than that of paramagnetic particle, the paramagnetic particle cannot be captured in the direction of magnetic field. The paramagnetic particles of different magnetization such as hematite, chromium oxide, perovskite and rutile are separated in different magnetization of fluids. These particles are present in the incinerated bottom ash. The separation is useful to recover titanium oxide from bottom ash and the removal of chromium of bottom ash is important to reuse the bottom ash as cement. The used fluids are paramagnetic liquids dissolving paramagnetic salts and the water based magnetic fluid dispersing the stable ultrafine magnetite. The dispersion condition of particles related to zeta-potential of the suspension feed is also important to separate effectively by controlling pH

Jan 1, 2014

By G. Voiloshnikov, A. Bogudlova

"The deleterious effect of carbonaceous matter during cyanidation of gold ores (so called preg-robbing) has been recognized for many years. Based on this, a new method using flotation to reduce the content of carbonaceous matter was developed. Low-sulfide gold-bearing ore with carbonaceous matter of 0.14% from a Russian deposit was processed. The purpose of these tests was to compare two flow sheet options. Option I comprised removal of carbonaceous product prior to sulfide flotation. Option II comprised removal of carbonaceous matter from flotation concentrate. It was found that the content of carbonaceous material can be reduced in sulfide gold-bearing concentrate prior to leaching. High gold recovery was observed during the separation of carbonaceous material prior to sulfide flotation using Option I. Due to lower reagent consumption the costs for reagents were decreased using Option II. The results have shown the effectiveness of a new method. Patent No. 2783808 was obtained for removal of carbonaceous material prior to sulfide flotation. This information will be used to design a large processing plant flow sheet in Russia."

Jan 1, 2014

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate. The technology has been tested on several different waters in pilot plant campaigns. Results obtained indicate that potable water can be produced (containing less than 200 mg/L sulphate and no heavy metals) as long as the monavalent ions (Na+, Cl-, etc.) are within limits.

Jan 1, 2003

By Anatoly Usov

The detailed researches of a broad circle of problems connected to development of the electric pulse method destruction materials (EPD) of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the device of electric pulse (EP) disaggregation and ?omminution of materials are developed, the technological efficiency of disintegration of industrial minerals estimated. Due to its technological advantages, the EPD could have a great potential in minerals mining and processing technologies. Low specific power and weight-and-size characteristics of EP installations based on the existing out-of-date electric equipment are at present the main reasons hindering the effective application of the method in mining and processing technologies. The main studies carried out in Russia in the field of electro technical equipment development for EP technology are presented. The pulse capacitors service life affects greatly the economic efficiency of the process because the capacitors cost accounts for a considerable, and in some cases, the most part of the operational costs. Determined and analyzed in the study are the ways which could significantly improve the specific characteristics of high voltage pulse generators (VPG), such as to use of high-frequency voltage transformation to develop a charger; to use pulse transformers (PT) with iron magnetic circuits made of materials characterized by high magnetic permeability, in pulse generating circuits; as well as to use special ways which could produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for EP devices, and a further strategy of the EP technologies development and application has been suggested on this base. Keywords: electric pulse disaggregation, electric pulse installation, charger battery, high voltage pulse generator

Sep 1, 2012

By Regis Texeira, Leopoldo Gutierrez, Vicente Hernandez, Caludia Vidal, Lina Uribe

"Molybdenum is currently the most important by-product of Chile´s copper mining industry. This mineral has gained international relevance over the years, because of its price. At mining deposits in Chile, copper and molybdenum are extracted together and then separated in a concentration process consisting of several flotation steps using sodium hydrosulfide (NaHS) as copper depressant. However, there are environmental issues related to the potential emisions of toxic hydrosulfide gas and bad odours, which affects nearby communities and suppose a risk for operators. This problem has led to the need for development of new technologies to eliminate the use of NaHS in the process of selective flotation of Cu and Mo minerals. In this work, results of flotation tests in which lignin derivatives reagents are used to obtain the selective separation of Cu and Mo minerals by flotation are presented. In this technology molybdenite is depressed by the action of lignin derivatives (lignosulfonates), while copper sulfides remain hydrophobic and float. The use of lignin derivatives in the selective flotation of copper molybdenum minerals represents a non-toxic alternative to NaHS.INTRODUCTIONSeparation of copper sulfides from molybdenite is commonly achieved through a two-stage flotation process. In the first stage the collective flotation of copper sulfides and molybdenite is promoted to generate a collective concentrate which is then treated in a second stage with sodium hydrosulfide (2.5-3.0 kg/t NaSH) to depress copper sulfides flotation without affecting the flotation of molybdenite. As a result a copper concentrate with 30-35% Cu, and a molybdenum concentrate with 50-52% Mo are generated. Although this process is widely used at industrial level, environmental issues related to the risk of H2S generation and bad odors have always been a concern. Thus there is a need in the industry for a more environmentally friendly process to separate copper sulfides and molybdenite."

Jan 1, 2018