Search Documents

By S. J. Ma

With the very effective depressant and collector developed by China Bluestar Lehigh Engineering Corp (hereinafter referred to as LEHIGH), satisfied results are obtained from laboratorial beneficiation tests on phosphate samples from Karatau, Republic of Kazakhstan by the direct flotation process. In this paper the effect of single factors on performance of flotation is studied and their applicable ranges are proposed. The final test results are described as follows: As the feed contains 23.20 % P2O5, and 3.96% MgO, a phosphate concentrate assaying 29.77%P2O5 and 1.54% MgO is produced, and the P2O5 recovery in concentrate is 88.28%. The beneficiation tests make it possible to simplify existing technology with fine grinding-desliming, followed by reverse & direct flotation system and consequently improve the concentrate grade and recovery for the future beneficiation plant

Jan 1, 2014

By Behzad Vaziri Hassas, Firat Karakas, Mehmet Celik, Onur Guven

Since dewatering is a costly process, removal of moisture from relatively fine size lignites is an important industrial problem. As the lignite gets finer, the presence of micropores and relatively low hydrophobic nature of lignite lead to trapping of large quantities of water in the coal matrix. Lignites used in power stations need to be dried to a certain degree of humidity before it is transferred to the combustion chamber. It is generally wise to dewater coal as much as possible by physical means before it is dried. However, dewatering cost in some cases may be prohibitive. Thus, sometimes removal of even little percent moisture may be of great help in such operations. Surfactants have been used to increase the efficiency of coal dewatering. It is crucial to select appropriate type and amount of surfactants in order to get higher efficiency. Since the hydrophobic characteristic of coals increases with increasing the coal rank, dewatering of bituminous and anthracite can be accomplished using low HLB surfactants (Oily), however, these surfactants are not efficient in the case of low rank coals like lignites and brown coals. It is suggested that adsorption of low HLB surfactants on high rank coals is governed by Acid-Base interactions rather than electrostatic and van der Waals forces. Since this characteristic in lignites is not strong enough, low HLB surfactants could not be effectively adsorbed on low rank coals to make surface more hydrophobic. In this paper, a special set-up has been designed to study the effect of high HLB surfactants on dewatering of fine lignite particles. It is shown that high HLB surfactants function more efficiently on low rank coals than low HLB ones.

Jan 1, 2014

By M. S. Prithvi

Over the decades, mine and mineral processing plant operations for the most part, have been found to have had adverse impacts on the environment. At the same time, mineral processing and mining operations produce mineral products that are indispensable to modern society. Thus, the sector has desirable and undesirable attributes simultaneously. The situation presents itself as a contradiction (i.e.) the mineral processing and mining operations are wanted by society, and at the same time unwanted by society. The existing methods of addressing the issues raised above have evidently not been very successful in reducing the opposition to new projects and to the related activities such as land acquisition. This paper attempts to show the relevance and applicability of TRIZ for addressing the issue. TRIZ, or Teoriya Rezheniya Isobretatelski Zadach, is a Russian acronym meaning Theory of Inventive Problem Solving. TRIZ is a powerful tool that can be usefully applied to resolve such contradictions, using resources usually available within the system of interest. Accordingly, this paper introduces the issue background, followed by an introduction to some key concepts of TRIZ such as the 40 principles, separation principles and directed evolution. The paper goes on to apply the 40 principles to two case studies. The results show that TRIZ could be a useful tool to generate potentially innovative and sustainable approaches. Its most appropriate position would be as a supplement to current decision-making procedures, and as a validation tool to review existing solutions for possible improvements. Keywords: minerals, environment, TRIZ, contradiction, resources

Sep 1, 2012

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Jochen Petersen, Steven Bradshaw, Guven Akdogan, Ngoie Mpinga, James Mwase, Jacques Eksteen, Cornelius Snyders

"The platinum group metals (PGMs) and associated minerals are particularly refractory to most traditional direct leach processes. However, the remoteness of many new ore deposits, socio-political risks, the scarcity of skilled labor and constraints on the availability of water and electrical power makes it increasingly more difficult to implement the conventional mill-float-smelt-refine process routes to extract and refine PGMs in remote areas. This paper discusses a process to extract PGM’s from low grade ore and concentrate using a sequential stage heap leach process entailing heap bioleaching and high temperature cyanide leaching, and evaluates the feasibility of implementing a carbon-in-pulp process to recover the PGMs from the pregnant leach solution. The heap bioleaching extracts the base metals in an acidic sulfate medium using a mixed culture of thermophiles. After heap bioleaching the heap is reclaimed, rinsed, agglomerated and restacked for high temperature cyanide leaching where the cyanide liquor is directly heated via solar energy in panels. Palladium, gold and platinum are recovered during the cyanide leaching stage. The pregnant leach solution was evaluated for potential carbon-in-pulp adsorption and subsequent elution similar to gold processing. The kinetics of adsorption and elution compared well with gold adsorption and elution."

Jan 1, 2014

By Z. Naziemiec

Since several years in Poland a huge demands on mineral aggregates occur, for the reason of intensive development of housing and road industry, as well as industrial building. Limitations in re-sources of broken aggregates in Central and Northern parts of Poland cause, that both the non-waste production of aggregates with high quality and the production of alternative aggregates from recycling gain greater importance, nowadays. It entails increase in demands for crushing devices, which are easy and reliable in operating as well as inexpensive and enabling to obtain a good quality products. Jaw crusher, regarded as the most spread in Polish industry, meet these requirements, however, their crucial disadvantage is a large content of irregular grains in crushing products. Numerous investigations show, that the shape of grains is a significant feature of aggregates, which influences on durability and quality of produced concretes. The advantage of jaw crushers is their easy operation, low price as well as low amount of dusts (wastes) generated in comminution products in comparison to other types of crushers (i.e. hammer crushers).

Jan 1, 2014

By F. N. Shi

Ore breakage characterization plays an essential role in the design and optimization of comminution circuits. Recently, the JKMRC comminution research team has developed a Rotary Breakage Tester (JKRBT). The JKRBT uses a rotor-stator impacting system, in which particles gain a con-trolled kinetic energy and are impacted against the stator, causing particle breakage. The first unit of industrialised JKRBT was installed at the Anglo Research in South Africa in March 2007, and five more JKRBTs are currently being fabricated for some of the world?s major mining companies. In addition to the JKRBT, an improved breakage model has been developed at the JKMRC, which more accurately describes the effect of specific energy, particle size and incremental breakage caused by repetitive impacts. The validation outcomes show that the JKRBT, together with the new breakage model, generate statistically similar breakage parameters to the traditional drop weight tester (DWT), but with significant advantages over its predecessor. The limitations of the DWT, specifically its lack of precision of the energy input, the lengthy time required to run individual tests and the challenges en-countered in testing small particles, have all been overcome by the JKRBT. The recent developments in the JKRBT and the new breakage model offer several prospective applications. These developments have the potential to revolutionize the ore breakage characterization in the years to come.

Jan 1, 2014

By I. Baltov

The Chelopech Mine, located in Central Bulgaria, is one of Europe?s largest underground copper- gold mines, currently mines and processes approximately one million tonnes of ore per year. Copper concentrates containing gold and silver with significant arsenic content are produced and sold on the world markets. The operation was acquired by Dundee Precious Metals in 2003. A modernization program for the Mine and Plant has since been in progress to increase both production and mechanical reliability, and also to optimize metallurgical recoveries. Since then, mine output and plant throughput have doubled, plant availabilities and utilization have increased significantly, and overall metallurgical performance for copper and gold improved. The paper presents the systematic approach for obtaining and analyzing data, communicating it, and making suggestions for changes to the technological parameters and flowsheet in order to maximize metal recoveries. These studies have correlated the ore characteristics (particle size distributions, metal assays, and Cu and Au mineralogical and phase analyses) with the actual plant performance (kinetics, recoveries, and throughput). Cu recovery by size has been calculated from the mineralogical analyses of feed, concentrate and tails, with the most significant losses being identified in terms of fraction and phase recoveries. This has provided the recommendations (some of them tested in plant) for changes in the grinding and flotation circuits.

Jan 1, 2014

By M. Eraydin

Dewatering fine particles (e.g., flotation concentrates) is inefficient, energy intensive and often requires large capital and operating costs. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids and a hyperbaric centrifuge. Typically, the moistures obtained using these methods are 30% to 50% lower than those obtained using conventional methods, as demonstrated in laboratory and pilot-scale test programs. With another novel dewatering technology that has been tested in bench-scale tests, the moistures can be reduced to levels once believed to be attainable only through the use of thermal dryers. In this communication, test results obtained with these advanced dewatering technologies are presented and compared.

Jan 1, 2014

By V. A. Zhilina, I. V. Shadrunova, O. E. Gorlova

"The aim of the study is to develop and scientifically justify a new adaptive approach to the separating processes of deep and complex processing technogenic mineral raw materials. Technogenic mineral resources as a waste of mining and processing industry are mostly complex objects that have specific features of material composition and technological properties and make it processing ineffective with traditional schemes of mineral raw materials enrichment. Mineral wastes are regarded in this study as a complex object with a large number of signs in conditions of uncertain environment and object. However, adaptation is regarded as the process management system’ adaptation to the specific the properties of the object and the environment that has several hierarchical levels corresponding to different stages in the management of complex object. An adaptive approach is considered as a methodological basis of multivariate schemes for opening the mineral resources and creating mechanisms that could transfer these potential technogenic resources to the actual that significantly expand the mineral resource base of the country's black, coloured, rare, noble metals and construction materials. In this case, potentially the solution to the most pressing social and environmental problems associated with the adverse effects of past economic activity simultaneously with the commercial objectives. This approach to the wastes mining and related processing manufacturers meets the core idea of sustainable development as the balance of interests of State, society, business, private enterprise and each person in the areas of rational use of resources, economic efficiency and environmental safety. On the example of metal-containing raw materials in the form of slags of ferrous and nonferrous metallurgy, ferrous metallurgy sludge, mature fine tailings, the application of adaptive approach illustrates to the development of technologies of its deep and complex processing as phased, thoughtful movement from a comprehensive study of technogenic raw materials to build optimal topologies of technological schemes for processing the mineral wastes. INTRODUCTION Involving the Russian economy in the system of global economic relations significantly changes the nature of the country's competitiveness in the development of the world market and urgently requires competent management of its own natural and mineral resources. The latter at the present time in real economic processes cease to be a passive material foundation and become the producing basis in the production processes in the status of so-called natural capital. Introduced in the field of economic theory at the end of the 20th century, this term means both the flow of natural services and real natural resources. Consequently, natural objects, which act as natural resources of a certain production, today must necessarily be evaluated in a strategic sense. Modern standards of sustainable development presuppose that the economy should equally be oriented to balance the interests of the state, society, business, individual enterprise and each person in the spheres of rational use of resources, preservation of healthy ecosystems, ensuring well-being, high quality of life and environmental safety of not only the current generation, but also respect for the rights of future generations, that is, intergenerational equality. Most types of minerals are classified as non-renewable resources, therefore resource-saving in the sphere of mineral and raw materials complexes is one of the most important factors-indicators characterizing the degree of approximation to the model of rational subsoil use, and, consequently, sustainable development (State Report, 2017)."

Jan 1, 2018

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"The effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases.Electrokinetic methods were used to elucidate the mechanism of surfactants adsorption and to correlate these findings with the optimum flotation conditions. The polymeric surfactants would reduce the negative values of zeta potential of quartz while the reverse is true for feldspar. After treatment of microcline with HCl, its electrokinetic behavior in the presence of Tritons X surfactants became similar to that of quartz.The obtained results would suggest that separation of quartz from feldspar using nonionic surfactants of octylphenoletoxylated alcohols having shorter oxyethylenic chain length at low pH could be achieved"

Jan 1, 2003

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014

By H. Ding

Calcium carbonate/Titanium dioxide composite, characterized by coating TiO2 on the surface of CaCO3 particles, is an important substitute for titanium dioxide. This paper studies preparation method of CaCO3/TiO2 ,composites based on mechano-chemical effects, measures its properties as a pigment, analyzes the binding form and interface reaction mechanism between CaCO3 and TiO2. Through single finely grinding of CaCO3, co-grinding of CaCO3 together with TiO2, and mecha-no-chemical effects produced in the course of grinding, CaCO3/TiO2 composites can be prepared successfully. Results indicate that grinding fineness of CaCO3, co-grinding time of CaCO3 and TiO2, the weight ratio of grinding media to mineral feeding, and the amount of TiO2 have much influence on the properties of CaCO3/TiO2 composites. CaCO3/TiO2 composites have the properties same as titanium dioxide pigment, oil adsorption and ultraviolet adsorption same as TiO2, and 90% of hiding power as that of TiO2. Wet grinding of CaCO3 causes the production of mechano-chemical effect and hydroxyl group, through which CaCO3 and TiO2 can be bonded together. Repulsion occurs between the particles of CaCO3 and the particles of TiO2, respectively, they are both in good dispersion. But attraction occurs between CaCO3 and TiO2. TiO2 particles are distributed evenly on the surface of CaCO3. Therefore, coating of TiO2 on the surface of CaCO3 particles and chemical bond between them make CaCO3/TiO2 compo-sites have pigment properties of Titanium.

Jan 1, 2014

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

By B. Peszko

There are many measuring methods of grain sizes. Taking into consideration the fine grained materials, one of the existing techniques is measurement of grain size by the Coulter Counter method. This method is based on the measuring the changes of electrolyte resistance during grains flow through the calibrated diaphragm. This method is relatively simple to apply, significantly precise and the results are given quickly. However, the problem is that the measurements are limited by the size of diaphragm. Because of this situation, measurement of grain sizes by this instrument is possible in range from 10% to 60% of diaphragm diameter. This limitation causes the necessity of re-placing diaphragm in case when the measured grain size distribution concerns the material of large size range. In purpose of determining the total grain size distribution, the synthesis of some partial distributions, given for individual grain fractions (with different diaphragm applied), is required. This is possible to do by calculating the mixture of distribution functions, created from the partial distribution functions. Two materials were selected to research: quartzite and glass, which were comminuted in cylindrical crusher, additionally grinded, screened and then analyzed by Coulter Counter for five grain fractions: 0~125 µm, 0~80 µm, 0~56 µm, 0~40 µm and 0~25 µm. For each fraction, five different partial distributions were given (in case of glass ? four), which are the basis for the creating the joined grain composition. To assure the adequacy of the given distribution function, it is necessary to obtain the possibly best approximation of partial distributions. In the work, both the parametric and non-parametric methods of density approximations of investigated random variable. For each grain fraction the approximations were done by three traditional distribution functions: RRB, GSA and log-norm distribution functions and three methods of non-parametric approximation: Gauss kernel, Epanechnikov kernel and orthogonal Fourier series method. As the criterion of the certain distribution function acceptance, the value of the residual deviation was assumed, given by the formulae:

Jan 1, 2014

By D. Renda

With thise Process of obtaining a solid fuel which is both ecological clean and has a high calorific value by a two-stage method of enriching preferably type lignitic coals to remove a high content of all sulphurs, incuding organic sulphur, which method comprises converting the coal to a semi-coke from followed by magnetic separation. In the Experiments given the best results the washed lignite coal in the West-Turkey, Tavsanli- Region, size -3.35 mm on dry basis. In the microscopic studies of the brigh-thin cross-section taken from the samples of sulfur min-erals pyrite in the dimension of 2~50 micrometers and melnicovite 10 micrometers particles. An thermal treatment an semi-coking themperature between 370°C to 650°C give the best Result of 480 °C. The oxidation and decomposition of sulphur minerals pyrite and melnicovite in lignite coal proceed the iron oxides Fe2O3 and pyrrhotite FeS on the surface layer. The Magnetic Seperator (Rare Earth Magnetic Separator, REMS) is capable this two form of sulphur, including organic and inorganic sulphur, in semi-coke and resulted in the magnetic-fraction in REMS. The non-magnetic-fraction remove total sulphur by 68 %, ash by 44 % and increase the upper calorific value in 15 %. The clean lignitic coal can be utilized in human or energy power stations.

Jan 1, 2014

By B. Csoke

In a first stage of our investigations material properties of fly ash (three acidic and one alkaline type originating from combustion of various age coal) obtained from four various dumps have been characterized. In a next step systematic mechanical activation experiments??grinding??and measurements have been performed with various ashes to establish relations between grinding fineness (specific surface area), specific work input demand of grinding and activity. In a third phase utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of interrelationship(s) between the degree of activation of fly ash, the lime concentration and the resultant strength of the obtained concrete. Finally, pilot size experiments were conducted and a test road section was built to explore possibilities for the production of suitable binding composition from the mixture of fly ash and lime as well as the applicability such mixture for road construction. After summarizing major achievements of the first and second stages of the work (history) the present study deals with the research conducted in stages three and four. Experimental results support the conclusion that the obtained binding material is suitable for construction of road bedding.

Jan 1, 2014

By Auhin Kumar Maparu

Metal oxide nano-particles are used as additives in various industrial applications such as pigments in paints, additives in adhesives, plastics, cosmetics, functional coatings, personal care and health care products, for antibacterial applications and more recently in heat transfer applications. In most of these applications, usually dry nano-particle powders are added to the formulations. However, often it becomes difficult to achieve a uniform and stable dispersion of nano-particles in the given formulation. Thus, a scalable and commercially viable process for in-situ production of stable nano-particles suspensions in the desired medium will certainly be more beneficial. Ultra-fine grinding in high energy mills (planetary mill, stirred media mill) has been used to produce fine particles (sub-micron size). However, in order to obtain nano-particles (particle size <100 nm), the choice of appropriate dispersant and solvent is crucial, since freshly generated nano-particles tend to agglomerate due to their high surface reactivity. We have employed molecular modeling (MM) based selection methodology to arrive at the most suitable solvent?dispersant combination for preparation of the given metal oxide nano-particles. Molecular modeling techniques are employed to compute the interaction energy of a given dispersant with surface of the metal oxide particles in the presence of the dispersion medium. The interaction energy helps identify a dispersant that has strong affinity for the metal oxide surfaces allowing for strong dispersant adsorption and hence a more stable dispersion. For example, in case of aqueous nano-titania suspensions, poly-carboxylic acids like citric acid provide better dispersion than mono-carboxylic acids like lauric acid, mysristic acid, and oleic acid. While in non-aqueous medium like ethanol, p-hydroxybenzoic acid and glycerol trioleate perform better. The suspension is produced in-situ by ultra-fine grinding of the metal oxide powder in the presence of the selected dispersant and dispersion medium in a planetary ball mill. By careful selection of various process parameters such as percent loading of powder, jar filling, grinding media to powder ratio, time and amount of dispersant addition, both aqueous and non-aqueous suspensions of metal oxide nano-particles with average particle size less than 100 nm are produced. The aqueous suspensions of alumina and titania produced in presence of citric acid dispersant exhibit median particle size of 83 and 62 nm, respectively. These suspensions have been found to be stable for nearly 3 years. The nano-particles thus produced are used in the preparation of nano-fluids?advance heat transfer liquids, which show enhanced heat transfer capabilities and unaltered stability and performance even after several heating-cooling cycles. The nano-particles are also utilized for making efficient photo catalysts, which are found to be highly effective under sunlight. Keywords: stability, nano-fluid, milling, grinding, thermal conductivity, nanocoolant, photocatalyst

Sep 1, 2012

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003