Search Documents

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By E. M. De Souza, A. M. Coode

"When Canadian potash was brought into production in the 1960s substantial research was carried out to develop the technology needed to cope with the unique conditions in Saskatchewan mines. The intense research has established Saskatchewan&apos;s position as a leader in production technology on a world scale, and as a leader in setting international standards for potash production. The industry is now more than two decades old and, although the mines operate efficiently, there are a number oj prominent areas of concern. High among these is the prediction, prevention and control of sodium rich brine inflows. Control has proven difficult or elusive in the potash mining horizon, but work continues in this area. Control of brine in the superincumbent limestone formation has proven to be easier and more conclusive.The first part of this paper describes the rehabiltation, diamond drilling, and grouting completed at Central Canada Potash, which reduced the brine inflow from approximately 82 l/min . at the beginning of the work to O.9/1min. when the backfilling was placed.The second part of the paper describes the rationale for choosing the rock mechanical instrumentation, the reasons for their placement and the rock mechanical data recorded with some interpretation.IntroductionCentral Canada Potash is located approximately76 km southeast of Saskatoon, near the Yellowhead Highway. The commercial production of potash at CCP started at the end of 1969 at a depth of 1021m below surface. The potash zone, which is presently mined, is approximately 3.35 m thick . Stress relief methods using yielding pillars are used in the design of the mining layouts. The planned extraction ratio averages 35070 . The mine is designed to produce approximately 3.3 million tonnes of sylvinite per year to give approximately 1.3 million tonnes of finished product (muriate of potassium) per year."

Jan 1, 1990

By D. M. Baird

Copper mineralization occurs at several places along the shore of Notre Dame bay, Newfoundland, and at one time formed the basis of a considerable mining industry. The sources of the mineralizing solutions and the structural settings of some of the deposits have not been clearly understood. This paper reports new investigations into the origin and structure of the deposits between Bett&apos;s cove and Stocking harbour, in a strip about ten miles long and two miles wide along the western shore of Notre Dame bay. The most complete previous descriptions of the area are those of Snelgrove (1929, 1931, 1938), Douglas, Williams and Rove (1940), and the writer (1947). The discovery of the Bett&apos;s Cove deposits took place about 1860, soon after the discovery of the well-known Tilt Cove deposits to the north. Several other small prospects were found between Bett&apos;s cove and Stocking harbour between 1880 and 1910. At Bett&apos;s cove, active mining began in 1875 and a small smelting plant was built near the mine in 1877. .Mining operations came to an abrupt halt in 1883 after a major cave-in. In 1900, and again in 1906, attempts were made to drain the old workings and reopen the mine but were abandoned long before completion. Total production amounted to about 130,000 tons of hand-picked copper ore which averaged about ten per cent copper, and 2,450 tons of pyrite (Snelgrove, 1938, pp. 52-55).

Jan 1, 1948

By E. Mohammadi Zahrani

In this study, Mg-doped fluorapatite (Mg-FA) nanopowders were prepared through a sol-gel, technique and characterized. Designated degree of Mg2+ ions incorporation into the apatite structure was indicated by the x value in the general formula of (Ca10-xMgx (PO4)6F2), where x=0, 0.25, 0.5, 0.75, and 1. XRD, AAS, FTIR and TEM techniques were utilized to characterize the synthesized nanopowders. In vitro bioactivity of the powders was evaluated in simulated body fluid. Powders had a crystallite size less than 100 nm. It was concluded that Mg-substitution could alter bioactivity and dissolution behaviour of Mg-FA. These two parameters were proportional to magnesium content of the powders.

Jan 1, 2010

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

By Fathi Habashi

Poland has a unique copper industry. Copper sulphide concentrates are smelted in six shaft furnaces to produce matte and in a flash furnace directly to blister copper. Anodic slimes from electrorefining are treated by a modern technology to recover the precious metals. INTRODUCTION Poland&apos;s copper industry began in 1950 when the old and relatively small mines Lena and Konrad, located in Lower Silesia, were drained and recommenced production. In 1957 the industry entered a period of rapid development with the discovery of a rich ore body in the vicinity of Lubin and Polkowice which was the basis for the establishment, in 1961, of the Copper Mining and Smelting Combine (KGHM). In 1991 the Combine was restructured into a state-owned, joint-stock company under the new name of KGHM ?Polska Miedz? (KGHM ?Polish Copper?). It consists of three mines, three smelting and refining plants, and one rolling mill, and produces about 4% of the world?s copper and about 7% of the world?s silver.

May 1, 2001

Evolution of Maintenance Practices. Mechanization processes in underground mining operation became stronger in the 70?s - 80?s. Did maintenance practices changed over the years ? What are the the major differences of today?s practices? Speaker, Robert Hamilton Working at different positions into maintenance organization since over 25 years, Robert has accumulated a various and rich experience of ways to maintain equipment. He started as mechanic on construction projects and open pit mines. Early in his career Robert had supervision&apos;s responsabilities. He started in open pit operation (QCM) and after in underground operation with Lac Minerals, working at Bousquet, Doyon and Louvicourt mines, as U/G mechanical foreman and mechanical general foreman, and Maintenance superintendant with Cambior . He also experienced the underground mines equipments supplier&apos;s side working with Sandvik Canada.

Feb 1, 2008

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981

By Donald MacFadgen

Since 1950, a total of 164 miles of levels and rooms have been roof-bolted in the collieries of the Dominion Coal Company. Roof bolting is an efficient and economic method of sup-port where heavy timber sets or steel booms are necessary for temporary roof support, or where conventional methods of support interfere with the passage of mechanical mining equipment. This paper discusses present roof bolting practices and special bolting applications. THE practice of roof bolting in be collieries of the Dominion Coal Company dates from 1950, when preliminary studies and experiments were carried out in a mechanized room and pillar section of Dominion No. 20 Colliery. These studies were made in close liaison with members of the United States Bureau of Mines who were conducting similar studies. Following the successful application of roof bolting in No. 20 Colliery, this method of roof support was introduced into other collieries

Jan 1, 1963

By J. Petit

"In July 2004 workers at the ABI Smelter in Bécancour (Quebec, Canada) went on strike. Contingency plan were ready to face the situation and plan was done to operate one potline out of three. Two lines were stopped; keeping in mind the restart on cold metal after the strike was over. The subject to be presented and shared includes a summary of work organization including training, schedule of restart, pot cleaning, pot preparation, crash start method, follow up after crash start, safety and environment. This major project has been a very big challenge. It shows that people involvement is a must and the key success. It is then true to say : ""People who believe in success will work and act in order to get there"" and ""People who don&apos;t believe in success will act in such a way to fail"" Then both will prove they were right to think their own way ! Sharing such experience can be interesting because it&apos;s a true story and people like true stories."

Jan 1, 2006

By L. Yacher

Most metallurgical plants already have sophisticated control systems as well as a process-historian that manage thousands of real-time and historical variables. There exists a huge potential for operational improvement through the inference of patterns, correlations and cause-effect relationships within these records. The ability to run online and offline advanced multivariate statistical analyses represents a great potential for the mining industry, in various areas such as cathode quality improvement in an SX/EX plant, the analysis of the correlation between the ore characteristics and the mill throughput, the determination of early failure alerts for major equipment, etc. The background theory is described, as well as some practical experiences of operations in Chile and Peru. Cu2007

Jan 1, 2007

By R. D. Brown

In the spring of 1977, Revenue Canada announced its intention to proceed in 1978 with a plan to impute a taxable benefit on interest-free and low-interest loans provided to employees. Such loan arrangements are often an important aspect of the compensation packages provided by many companies to their employees. Since the original announcement, there have been many submissions to Revenue Canada opposing this change, and the Finance Minister has now brought down a compromise solution with the introduction of a proposed amendment to the Income Tax Act. The amendment, which would not take effect until the 1979 taxation year, would require an employee, a shareholder or a related person to include a benefit in income measured as the difference between the interest on any such loan computed at bank prime rate and any interest actually paid. Only the amount of such a benefit in excess of $500 in a particular year would be required to be included in income. Of particular interest is the exclusion from these benefit rules of loans up to $50,000 in respect of the purchase of a house on the relocation of an employee and loans provided for the purchase of shares of an employer corporation.

Jan 1, 1978

By Donald Brisebois

The mining of high-grade, narrow vein deposits is an important field of activity in the precious metal mining sector. The principle factor that has undermined the profitability and effectiveness of mining such ore zones is the substantial dilution that occurs when blasting with explosives during extraction. In order to minimise dilution, the Thermal Fragmentation Mining Method enables the operator to extract a narrow mineralised corridor, 50 cm to 1 metre wide (according to the width of the vein), between two sub-level drifts. By inserting a strong burner powered by diesel fuel and compressed air into a pilot hole previously drilled directly into the vein, a thermal reaction is created, spalling the rock and enlarging the hole to 80 cm in diameter. The remaining ore between the thermal holes is broken loose using low powered explosives, leaving the waste walls intact. This patented method produces highly concentrated ore, resulting in 400% - 500% less dilution when compared to conventional mining methods. The mining method reduces the environmental affects of mining operations since much smaller quantities of rock are displaced, stockpiled, and treated using chemical agents. The fully mechanised equipment operated by a 2-person team (1 thermal fragmentation operator, 1 drilling operator) maximises the effectiveness of skilled personnel, and increases productivity and safety. The Thermal Fragmentation is currently employed in 3 mining operations in North America.

May 1, 2010

In order to avoid impurity problem and enhance absorption/desorption kinetics of Mg-based compounds, nanostructured Mg-based compounds were synthesized from Mg, Ni and other elemental nanoparticles produced by hydrogen plasma-metal reaction. XRD and TEM results demonstrate that homogeneous nanostructured Mg-based compounds with less impurity were successfully synthesized by this method. DSC in hydrogen atmosphere, pressure-composition isotherm and the kinetics of hydrogen adsorption/desorption were investigated at different temperatures. The results show that the nanostructured Mg-based compounds can absorb hydrogen in a high speed at a low temperature.

Jan 1, 2005

By C. Langer

Although the existence of precious metals, particularly those of the platinum group, in the nickel ores in the Sudbury district has been known for a good many years- almost as long as the ore deposits themselves- the Mond Nickel Company were the first to effect their recovery on a commercial scale. The precious metals values of the different Sudbury ores vary considerably, and are generally higher in the copper-rich ores. These values are so very small that a direct determination in the ores gives quite unreliable results. This is not surprising if one considers that some of the ores contain on1y one unit of total precious metals in about two million units of ore, and that this one unit will consist of seven different metals, each with a different chemical behaviour. It is only after the ores have been smelted to a Bessemer matte containing about 80 per cent combined copper and nickel that the precious metals content can be determined with some degree of certainty. From the figures thus obtained, the precious metals content of the ores can be calculated, provided the tonnage of ore used to produce one ton of matte is known. The recovery of these minute quantities of precious metals out of ?such a large amount of gangue and sulphides of iron, copper, and nickel seems at first glance a commercial and technical impossibility. Nevertheless, science has found a way to conquer all the difficulties, and quite substantial quantities of the precious metals contained in the Sudbury nickel-copper ores have been regu1arly recovered for many years by the Mond Nickel Company.

Jan 1, 1927

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal, F. A. Muñoz

Different authors and publications indicate that Optibar Segmented Intercell Bars cause a remarkable distortion in the distribution of the current in a cell group. However, these results were based in inaccurate computer based models and do not represent the technology. During the last trimester of 2010, a 92 cells circuit from Barrick Zaldívar EW plant was implemented with Optibar Segmented Intercell Bars. The technology was incorporated progressively without disrupting the plant production. Depending on operational conditions, this led to a 2 to 4% current efficiency increase and 3 to 5% specific energy consumption reduction. By October 2011, 40,000 tons of copper will be produced with the technology.

Jan 1, 2011

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

By Mousa Mohammadi

Due to operational advantage of dragline in simultaneous excavation and back-filling, the equipment has gained vast importance in open-pit mining. Besides, absence of auxiliary haulage units and a myriad of other benefits are also credited in favor of excavation of muck piles by the draglines. However, the aspects of production, productivity and economics are of utmost significance in dragline operation and planning. In this light, the present paper is an endeavor to analyze availability and utilization of dragline operations. The paper presents a good amount of data for 4-draglines operating in one of the major opencast projects in India. The study reveals the trends of availability and utilization of these draglines during last 11-years. Furthermore, the study also highlights the salient reasons for loss of available hours and for idling of the draglines. Some startling information and facts have been illustrated in form of graphs and pie charts.

Aug 1, 2013

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006