Search Documents

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By W. H. Zieman

NORMAN WEISS, Milling Engineer, American Smelting• and Refining Company: The subject of the Forum on Rod and Ball Mill Liners is very fascinating, and there is no end of discussion when operators get together on grinding. However, the hypotheses and suppositions easily outrun the facts, especially when we •consider the inaccuracy of many reported observations. Still surprisingly small is the number of concentrators even reasonably well equipped to measure power consumption of each grinding mill, together with running time, so that data on this tangible factor, at least, can be obtained with precision. While the more elaborate devices of this nature, producing for each 24-hour period the total power consumption, average kilowatt hours per hour, short-term demand chart, instantaneous demand, and print-out, may cost in the neighbourhood of $2,500 per mill and may be difficult to justify, the combination of an ammeter, watthour meter, and running-time meter will cost only a few hundred dollars, so there appears to be little reason not to in-stall them in view of their numerous advantages.

Jan 1, 1959

By A. Fahr, T. Byczkowski, M. Genest, C. Mandache

"Layered aluminum structures assembled with rivets are often found in aircraft fuselage. These structures are exposed to various mechanical loads and a range of environmental conditions that contribute to their ""aging"". The rivet holes are the source of stress concentrations and the location of crack nucleation and growth. Detection and sizing of second and third layer cracks under fasteners represent a major challenge for non-destructive evaluation (NDE) technicians. Electromagnetic methods are currently the most feasible NDE techniques that are capable of successfully inspecting such structures. However, different probe lift-offs, due to protruding rivets and paint coatings, or interlayer separations, due to sealant or air gaps, pose difficulties in detecting and sizing cracks. In addition, the use of conventional eddy current technique is limited due to the inverse relationship between the probe spatial resolution and its field penetrability. In this paper, we present an alternative approach that overcomes the previously mentioned shortcomings by using pulsed eddy current excitation and magnetoresistive sensor pick-up. Various signal manipulations are employed for defect detection and quantification."

Jan 1, 2006

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By S. Akhlaghi

In many electronic/optoelectronic devices, interaction between the metal stack and solder is undesirable. If a reaction happens, a nonuniform joint containing spikes and voids is likely to form and as a result the heat dissipation deteriorates significantly, which in turn, leads to the degradation of the bond. In the present work the interaction between Ti/Mo/ Au metallization system, which was sputter deposited on AlN substrates, and Pb-Sn solder was studied by using scanning electron microscopy (SEM). Also, an EDX system was used to trace the changes in chemical composition of the layers after solder tests. The microstructural examinations show that the Ti and Mo layer from the Ti/Mo/ Au metallization system are not impermeable enough and thus Ca from the surface of the substrate moves all the way up to the interface of Au/Mo and forms an intermetallic at the interface, which grows over time.

Jan 1, 2006

By P. L. Schwartz

The present method of shipping potash to the myriad of consumers is inefficient, not only because of the extreme and unpredictable nature of seasonal demand, but also because railway car turnaround times are very lengthy. The Floating Train system employs unit trains of potash operating from Saskatchewan mines to distribution warehouses located throughout the six corn-belt states of Minnesota, Iowa, Wisconsin , Illinois, Indiana and Ohio, transshipment points at Thunder Bay and the U.S. waterway network, and, where applicable , large consumers. These unit trains would "float", meaning that they would not originate at the same mine nor terminate at the same warehouse on each trip . They would " float " freely among the origins, destinations and participating railways. The potash would be shipped uniformly throughout the year and usually stored in warehouses located within the six states. It would be subsequently delivered to consumers within a 75-mile radius. Distribution warehouses and rolling stock would be provided by a new company, Potash Distribution Limited, consisting of major potash producers and the Canadian railways. Potash Distribution Limited would be responsible for the distribution of potash from the origin through the warehouses to the final consumer. The additional costs of providing warehouse space and outbound delivery will be offset by the reduction in both rail rates and "peaking" expenses.

Jan 1, 1978

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

"THE GOLD MINING REGION of Timmins - Val d'Or, astride the Ontario-Quebec border, has long suffered the effects of rising costs during the period when the U.S. price of gold was fixed at $35 per ounce. The federal government, through such assistance programs as that set up under the Emergency Gold Mining Assistance Act (E.G.M.A. ) in 1948, has subsidized the gold mining communities of Canada for a total of over $300 million to March 31, 1972. Of this, the Timmins - Val d'Or ""gold belt"" has received more than twothirds, almost $220 million. In spite of these continuous subsidies, only 12 gold mines are still producing in the Timmins - Val d'Or belt, whereas 71 mines have received subsidies for some period since 1948. The vital question is how the communities previously supported principally by the mining of gold will survive in the long run, as many of the older mines either are already depleted or are quickly becoming so. With the rising price of gold on the 'free market in recent months, prospects look a little brighter for the time being. Even with the increased official price of U.S. $38, which made the maximum government subsidized price about $48 per ounce, gold mines have not sold any gold to the government since January 1972 and some stopped doing so months before that. The populace of the region has not been enthusiastic about relocation nor about extensive retraining programs in the past and probably will not be in the future. So, when the remaining gold mines become depleted, the old problems of community depression will remain."

Jan 1, 1973

By M. Mezbahul-Islam

Thermodynamic modeling of the Mg-Cu-Ni system is carried out as a part of multi component thermodynamic database for Mg alloys. This system is being modeled for the first time using the modified quasichemical model, which considers the presence of short range ordering in the liquid. The thermodynamic descriptions of the binaries Mg-Cu, Cu-Ni and Mg-Ni have been extrapolated to the ternary Mg-Cu-Ni system using Toop geometric model. The constructed database has been used to calculate and predict thermodynamic properties, isothermal sections and liquidus projections of the Mg¬Cu-Ni system, which showed very good consistency with the experimental data.

Jan 1, 2011

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy, E. D. Shepeta

This paper studies the features of known and newly synthesized dialkyldithiophosphates and reagents with thioamide groups when separating copper-containing and arsenic-containing minerals in the flotation of skarn-scheelite-sulphide ore at the Primorskaya concentration plant. The optimization of dialkyldithiophosphate collectors was based on the study of their surface activity at the liquid-gas interface and estimated hydrophobic abilities. The flotation experiments show that the selectivity of action of the reagent increases with an increase of its surface activity and a reduction of hydrophobic ability when separating chalcopyrite and arsenopyrite. IMA-225-5 was proposed as a more efficient dialkyldithiophosphate collector, which increases the recovery of copper by 2.8% compared to the industrially used collector IMA-I413. Selection of the optimal structure for reagents with thioamide groups (derivatives of thionocarbamate and thiourea) was carried out according to their acidity and the presence of hydrophilic particles in their structure. Calculations were performed depending on the pH of the solution of chalcopyrite to determine the optimum reagent sorption and to further optimize the structures of these reagents. The tests with reagents with thioamide groups show an increase in copper recovery by 3-4% together with a significant increase of arsenic content compared to IMA-225-5. As a stronger collector with thioamide groups, it was recommended to use sample 234, which belongs to the thiourea derivatives. IMA-225-5 was recommended for industrial tests at the Primorskaya concentration plant. Thus, this study has shown that using dialkyldithiophosphate is more appropriate if it is necessary to increase the selectivity of separation of copper-containing and arsenic-containing minerals, and using reagents with thioamide groups, or their combinations with dialkyldithiophosphates, is more appropriate if it is necessary to increase the recovery of copper or the quality of copper concentrate with less selectivity of the process.

Jan 1, 2016

By R. D. Brown

For the first time in years, the spring budgets of federal and provincial governments have not brought down major new proposals affecting the tax burdens of the mining industry in Canada. It seems appropriate to use this unaccustomed period of tranquility to set out an extremely abbreviated summary of the principal features of the federal and provincial income and mining tax rules affecting the mining industry.

Jan 1, 1977

By E. Thomson

This type of microscopic investigation, although still in its infancy, has already found practical applications in several different phases of mining activity. The study of the transparent minerals in rocks, by means of the ordinary petrographic microscope, has for long been a very useful supplement to observations in the field, but the opaque minerals, until recently, have had to rest content with a more or less superficial determination with the hand-lens or the blow-pipe. In a great many cases, particularly where the association of metallics has been somewhat complex, this has been entirely inadequate, and the determination of these opaque minerals under the micro- scope, has opened up a new field of scientific investigation that bids fair to surpass, in practical value at least, the micro-scopic determination of the rock-forming minerals. As the details of this kind of microscopy are possibly not entirely familiar to all mining men, it might be well to outline them very briefly before dealing with the practical directions in which this method may be applied. The ordinary petro-graphic microscope, with but one extra attachment, will serve for this work. A small reflecting device, called a vertical illuminator, is inserted immediately above the objective lens. This reflects the light down to the surface of the specimen and from here the light is directed up the middle of the microscope tube to the eye. As it is desirable that the maximum amount of reflection should be secured from the surface of the section, it is first polished and set in a position perpendicular to the vertical axis of the microscope.

Jan 1, 1924

By Hans Lundberg

An electric survey from a 'plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the 'plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the 'plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the 'plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the 'plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the 'plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By R. Edinger

Aerospace and space products depend, probably more than any other products in industry, on advanced materials. While there are many ways of producing aerospace parts, in many cases the process does not allow the design of the metallurgical properties according to the part or product requirements in accordance with its mechanical configuration. Key to the next level of innovative manufacturing is the capability to control the amount of energy applied to the process, as well as the addition of materials in form of vapor or solid particles such as powder in order to build up the metallurgical composition required. With the development of a high speed pulsed laser-electron beam source, the LASTRON(TM) technology, we deliver the basic requirement for a digital manufacturing process of aerospace and space products. This technology, combining Laser and electron beam, finds application in welding, drilling-machining, and is currently modified to allow digital coating (PEB-PVD) methods. In addition to the coating, a powder metallurgical process, called Rapid Manufacturing (RM), will allow the precision melting of parts based on CAD/CAM files. The RM process and the digital coating will allow the production of graded aerospace alloys in parts for jet engines and aero-structures.

Jan 1, 2006

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By David Weiss

There is significant interest in magnesium alloy castings because of their low density and high strength-to-weight ratio. Lightweight, structural materials are in demand for aerospace components, hand tools, electronics enclosures and have found increased use in automobiles. Increased use of magnesium will depend on the resolution of a number of materials issues and development of more robust and economical casting processes. Most magnesium components are produced via high-pressure die-casting. High levels of porosity generally prevent die-castings from being used for structural applications. Structural castings are usually produced using sand casting, a relatively expensive casting process. Some work has been done on development of lower cost structural casting processes, such as lost foam casting, permanent mold casting or low-pressure casting. New programs are also emphasizing improvements to the die casting process. Research and cost reduction needs are discussed with respect to current programs and future components.

Jan 1, 2006

By M. E. Moraes Castanho de Almeida, A. Ribeiro Cotri

Recovery of cobalt to produce high grade cobalt sulfate from cobalt concentrate by leaching and solvent extraction was investigated. The PLS typically contains Co 10g/l, Mg 2g/l, Fe < 10ppm, Mn < 200ppm, insolubles <100ppm and is extracted with 20wt% Cyanex??272. The typical strip solution contains Co 60g/l, Mg 0.03g/l, and was sent to the current process for the production of cobalt sulfate heptahydrate. The cobalt yield of the plant with two extraction steps was 92%, with three steps was 97% and with four steps 99%. The extraction stage used the concept of "scrubbing" in a countercurrent system. In the first stage of extraction pH was 4.8, and in the last stage of extraction pH 5.5 to promote the exchange of magnesium in the organic with cobalt contained in the PLS. Following the extraction, when using two scrubbing stages, Co/Mg selectivity between of 2,000-3,000 was obtained, and with three scrubbing stages, selectivity was greater than 6,000. The desired selectivity was reached when using a scrubbing configuration with O/A ratio of 10:1. The typical cobalt sulfate heptahydrate had the following composition: Co 20wt%, Mg < 0.01wt%, Fe < 5ppm, Mn < 0.01wt%, Cu < 0.01wt%, Zn < 0.01wt%.

Jan 1, 2014