Search Documents

By H. Sahay

This paper summarizes the history and ore-grade statistics of mining the Ming orebody, and then details the mining methods. Included are raising, stoping, drilling and blasting techniques. Particular attention is paid to ground support, ventilation and pumping requirements.

Jan 1, 1979

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005

By Raymond C. Voige

"The use of current electronic technology in the design of new underground mine communications equipment is providing improved and expanded voice communications which can, in turn, contribute to improved productivity and safety. A review of equipment that is now available or under development Includes the following categories:WIRED SYSTEMSI.Pager phones with selective calling, audible and visual alerting and message indicator.2. Mufti-conversation pager phones that use multiwire cable ormultiplexing techniques.WIRELESS SYSTEMSLow-and medium-frequency inductive systems utilizing ""near"" magnetic fields for both vehicular and personal communications.Wired SystemsCommunication systems in underground mines have evolved slowly in many parts of the world. For many years, magnetotype telephones were the only means of communication from one mine level to another and to the surface. These units were located near the shaft and communications to the working areas were limited."

Jan 1, 1981

By Paul Grady, Martin Froehling, Curtis Mohns, Eliab Roman

"Since the idea of processing rock to unlock the valuable minerals inside was put into practice, efforts to improve production began. Methods have been learned that allow for operation in environments and under circumstances where it would not have been possible until now. All existing operations have experienced at least some form of productivity improvement measures. The objective is simple: generate more product of better quality in less time and at lower unit cost. Since the year 2000, various modifications have been made at the Kemess Concentrator in efforts to improve productivity. The following is a discussion of these modifications and their contributions to the success of the operation.INTRODUCTIONThe Kemess South Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines with a modern mill controlled by a fully integrated Foxboro IA DCS system and employing 134 people. On February 11, 2000 Northgate Exploration Limited (now Northgate Minerals Corporation) acquired Kemess Mine from receivership. Since acquisition in 2000, Kemess has seen many accomplishments, including the reduction of costs by 40% site wide.The mill has a nameplate capacity of approximately 56,000 tonnes per day which is processed through a Metso (Svedala) 60” x 89” Primary Gyratory Crusher and then conveyed by a 60” conveyor to a stockpile with 48 hours of total storage capacity. The nominal minus 6” rock from the stockpile is fed to two parallel grinding circuits (A & B). Each section consists of a 10.4 m F x 4.7 m SAG mill with dual drive motors (4,480 kW apiece) discharging onto a 2.4 m x 7.3 m Metso (Svedala) single deck vibrating screen to remove the coarse material for recycle to the SAG mill by a Continental 45º high angle sandwich conveyor. Screen undersize is pumped along with ball mill discharge to a cyclopac consisting of twelve Krebs 66 cm F cyclones to classify flotation feed to a size of approximately 65% minus 200 mesh. Cyclone underflow feeds a Metso (Svedala) 6.8 m F x 11.0 m ball mill, also with dual drive motors (4,480 kW apiece). The primary grinding circuit has 35,840 kW available for grinding."

Jan 1, 2005

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By Matthew P. Wickham

The use of existing mine records in conjunction with an appropriate classification scheme can be used successfully to identify and characterize the composition of existing waste rock facilities where traditional approaches based on sampling may be impractical or costly. This paper describes an alternative approach used in an acid rock drainage investigation at a porphyry copper mine with numerous waste rock dumps of varying ages and composition. The approach integrated detailed lithologic and mineralogic information about the ore body and overburden materials with records of pit development and dispatch. A waste rock characterization matrix was developed for the site to meaningfully classify lithology and mineralogic composition of the waste rock. The approach resulted in a focused geochemical testing program and facilitated interpretation and application of the test results.

May 1, 2002

By J. -P. Saindon, L. D. Nel, A. E. Hall, S. G. Hardcastle

"This paper reports on an investigation into gas and dust concentrations in Ruttan Mine's exhaust air. The values obtained indicate that there is excellent potential to recirculate approximately 25% of the hot exhaust air into the intake air to reduce winter heating costs. Contaminant concentrations vary significantly during the course of the working shift and decrease in the mine exhaust system as the air returns to surface. A proposed on-line control system is outlined which would permit recirculation to be implemented with a pay-back period of less than two years. IntroductionIncreased energy costs and depressed mineral prices have resulted in mines, which use winter ventilation air heating, reviewing their systems to try to reduce costs. Heating costs can be significant, for example, Potash Corporation of Saskatchewan spends an average of $580,000 per mine per year and Ruttan mine spends approximately $IM per year on propane for its direct-fired heating system.Several method s of reducing heating costs have been considered and the following have potential application.Heat Exchange Between Exhaust andIntakeThis is usually accomplished by run-round glycol systems. The system is limited by ice formation on the coils in wet exhaust air and by the low exhaust air temperature, usually l0ºC. It also requires close proximity of the intake and exhaust airways to ma~e the cost of the connecting pipeline and pump systems economic . A feasibility study by Inco's Thompson operation reported that a proposed system of this type had a 19-year payback period and was, therefore, uneconomic. Potash Corporation of Saskatchewan is currently investigating plastic heat exchangers for a trial system because of corrosion on metal exchangers. It has the advantage of a 17°C exhaust temperature and relatively dry exhaust air.Waste Heat ReclamationThe waste heat from compressors and hoists can be used for heating in some mines. The feasibility of such a system depends on the individual layout and the proximity of the heat source to the inlet airway. Other mines have considered using the exhaust air in greenhouses to provide a cash crop."

Jan 1, 1988

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surface disposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash."

Jan 1, 1980

By P. A. Witt

"Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located 75 km southwest of Kamloops, British Columbia (Fig. 1).The ore is situated within a porphyry copper deposit and is mined at a rate of 135,000 mt/day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 people and is planned to operate until 2009. The operation is a partnership between Teck Cominco (63.9%), BHP Billiton (33.6%), and others (2.5%). Management is shared by the two principal owners and directed by a management committee."

Jan 1, 2005

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By J. Châteauneuf, R. Dupéré, D. Mrabet

"In gold processing plants, it is common to start gold cyanidation in the grinding circuit by simple cyanide addition or as a result of recycling residual cyanide. In such cases, advantages such as a decrease in gold lockup and reduced leach time have been noticed. The prevailing conditions in grinding circuits such as intense mixing, particle breakage and friction or high temperature are quite different from those found in tanks and so is the resulting cyanidation behaviour. To gain a better understanding of the cyanidation behaviour in mills and of the pertinence of cyanide addition in grinding circuits, lab tests were conducted using an industrial ore from Canadian Malartic mine. In this study, the effects of different parameters on cyanidation in grinding circuits were examined; parameters such as such as temperature, dissolved oxygen, cyanide concentration and pH. The results showed that the kinetic benefits of high temperature in the mill can overcome the low dissolved oxygen concentration thus leading to an overall gold dissolution kinetics improvement for temperatures up to 50°C. However, gold leach in the studied grinding circuit at lab scale caused an increase in cyanide consumption with a higher generation of iron cyanide and SCN-. These results were confirmed by tests in the Canadian Malartic plant where the cyanide addition was moved from the SAG mill to the leaching tanks resulting in a 20% savings in cyanide consumption.IntroductionCyanidation in grinding circuits can benefit gold processing by decreasing gold lockup and by reducing leach time. However, other aspects regarding gold and cyanicide dissolution come into play in the conditions prevailing in grinding circuits. Indeed, high turbulence, high temperature, recycling load, friction and particle breakage make cyanidation behaviour in grinding circuits different from in-tank cyanidation (Marsden and House, 2006). In several cases, cyanide in grinding is limited to a very low level or completely avoided such as in circuits with gravimetric separation, for ores requiring oxidative pretreatment or for preg-robbing ores. In other cases, water management imposes a certain recycling of residual cyanide. This problem is generally addressed by a case-by-case approach. However, the chemistry of cyanidation in mill circuits is worth investigating in order to assess the advantages and disadvantages."

Jan 1, 2016

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By Nilce Alves Santos, Vânia Lúcia de Lima Andrade, Keila Lane Carvalho Gonçalves, Harold Wyslouzi1

"When confronted with the difficult decisions on advancing an exploration project to the feasibility and construction stages, it is important to know how various regions of the ore body will react in the milling and concentration processes. While bench scale test work is common and inexpensive, the results and information provided are somewhat limited due to the difficulty in accurately predicting the effects of recirculating middling streams or gradual changes in solution chemistry.Conventional Pilot Plants, processing 100 to 1,000 kg/hour of sample ore, provide the detailed engineering data required to develop a final process flowsheet and to size the equipment. They are, however, expensive to set-up and operate, and are really only viable for major projects that are well advancedIn the latter part of 1999, the Mineral Development Center at CVRD (MDC) purchased a new piece of mineral processing equipment which can run continuous flotation tests using drill core samples. To evaluate its performance, and to compare it with conventional testing methods, various types of flotation tests were carried out using two different types of copper ore. The limitations and advantages of open circuit and locked cycle bench tests, as well as the Mini Pilot Plant and the Conventional Pilot Plant were evaluated.Open circuit tests carried out at the bench scale only provide basic information. More complete and trustworthy information is obtained, in terms of the recirculation of flows and reaching a permanent and stable flotation regime, as the dynamics and complexity of the tests increases. The data obtained showed that the MPP’s metallurgical performance was equivalent to that of a conventional pilot plant."

Jan 1, 2002

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003