Search Documents

By S. Rash Ahmadi

Thin brittle coatings are deposited or developed on component surfaces for different reasons. In many practical applications the coatings are stressed by externally applied loads. Under such conditions, coating failure can occur. In this paper the probability of the extension of surface crack in coated materials due to cylindrical sliding indentation is analyzed. Contact loading problems typically result in multi-axle and strongly inhomogeneous stress fields near the contact surface. This property which strongly affects the stress intensity factors is taken into account in the failure analysis. Edge cracks were selected to model the actually accruing surface flaws. A suitable method is described for calculating the contact stress fields in coating and substrate. The coating is idealized as a brittle-elastic layer of uniform thickness, which is bonded to the surface of a half space. Method of linear elastic fracture mechanics are then used to calculate the load required to cause fracture in the coating.

Oct 1, 2011

By S. A. Sadough vanini

In this paper the influence of temperature on the flow behavior and rheological characteristics of an A356 alloy in the semi-solid state using backward extrusion process are studied experimentally and numerically. Simulation process is done by dynamic explicit in ABAQUS software for each forming condition. A cooling slope treatment was employed in order to obtain a non-dendritic microstructure. Experiments were performed in 5 temperatures and 4 different wall thicknesses. In the low forming speeds, liquid fraction had time to escape from solid phase forward the samples? wall. This condition was the main reason for the segregation phenomenon seen in the base and walls. Viscosities were determined using the force-displacement graphs obtained form back-extrusion tests. As observed experimentally, in a constant temperature, increase of shear rate resulted in decrease of alloy viscosity exponentially. Raising the temperature increases the liquid fraction hence reduces the semi-solid alloy viscosity. The results of experimental and simulation are compared and there is a good adaptation.

Oct 1, 2011

By T. Ward, K. Shah, K. Murray

The mining industry is processing deposits with ever decreasing grade at ever increasing operating costs while margins are under constant pressure by material substitution and recycling. We are reaching the point where building it bigger just isn’t good enough as social and environmental constraints become more intense. In response to the growing demands on our industry, Goldcorp has embarked on a journey to increase resources by converting Waste to Ore. Gravity pre-concentration and sensor sorting testwork has been completed on samples from our Canadian operations in order to determine the amenability of our mineralized waste to sorting and upgrading. As expected some material was amenable to sorting and a review of the economics supported demonstration plant testing. The ability to economically sort mineralized waste into ore and barren rock is being demonstrated by Goldcorp. It has been made possible by leveraging the experience mineral sizer manufacturers have gained in the oil sands and hard rock applications, seeking more energy efficient screening machines and embracing the advancements that ore and recycling sorter suppliers have achieved. The paper will discuss the testwork and results achieved to date from both the lab and demonstration plant.

Jan 1, 2018

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

Introduction A Hypothetical Scenario: Suppose that your company's research department has developed a new device which represents a significant innovation. You would like to begin selling it as soon as possible. The new device has not been publicly disclosed. You're not sure about what type of intellectual property protection you should be seeking, or when you should be seeking it. As discussed below, assuming that the costs are worth it, a patent application probably should be filed before any public disclosure is made. In general, if you do not file a patent application prior to a public disclosure, you will lose rights. Major Types of Intellectual Property In this paper, intellectual property protection is broadly discussed. Practical steps which can be taken to minimize the possibility of losing intellectual property rights (and maximizing the possibility of benefiting from your company's intellectual property) are outlined at the end of this paper. The issues discussed in this paper are somewhat complex, because a number of outcomes are possible, depending on the facts. It is strongly recommended that you seek legal advice in your jurisdiction in connection with any particular circumstances relating to intellectual property rights. "Intellectual property" refers to a number of different types of rights. The major types of intellectual property are: (i) patents; (ii) trademarks; and (iii) copyright. Trade secrets are also usually considered to be a type of intellectual property, and they are also discussed in this paper because of their importance. In general, each of these types of intellectual property protects different subject matter, although there can be some overlap. Intellectual property rights are generally territorial in nature. The scope of protection of a type of intellectual property in a country (e.g., patent protection) depends on whether the specific national requirements for protection have been met.

Feb 1, 2008

By I. Colquhoun

Current practice tends towards "integrity as an afterthought". That is, integrity is treated as an isolated aspect of operations and maintenance. In fact, this works quite well. But it would work so much better and with less uncertainty if integrity management measures were introduced at the design phase and addressed the entire life-cycle of the pipeline asset. The talk will address the measures and metrics that can be implemented on a new pipeline during design to optimize integrity and deliver a comprehensive operating manual and integrity management program for the pipeline system. This deliverable should describe the risks to be assessed and monitored, and the actions to be taken to control these risk adequately. Properly executed, integrity by design will provide a good working estimate of the life-cycle integrity management costs and maximize system reliability.

Jan 1, 2005

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By Rashid Bashir

Shaft sinking through solid rock, which contains little or no water, poses little difficulty. However, when loose, water-bearing strata have to be contended with, water control measures, and pumping facilities are needed. Shaft sinking in Athabasca Basin requires sinking through water bearing sandstone which can be highly fractured. Intersection of local zones of extensive fracturing results in the potential for high water inflows with pressures up to 5 Mpa. Grouting is carried out ahead of each shaft sinking interval as water control strategy. In the grouting method, liquid cement is forced into the water-bearing earth under very high pressure. Shaft sinking performance which can be quantified in terms of rate of advance is highly dependent on the days spent at each interval grouting before sinking can advance to the next interval. This paper presents the shaft sinking experience in Athabasca basin and how some of this is translated into Geoscientific Investigations for Future Shafts. A comparison of Geoscientific data collected from future shafts at McArthur River and Millennium Mines is compared to historical data collected from pilot holes, where shafts have already been sunk. The paper concludes with the strategies for better integration of hydrogeological, geotechnical and geophysical data.

Aug 1, 2010

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By Rashid Bashir

The presence of groundwater in the form of large aquifers can have an important influence on investment decisions for underground mines. The design for such mines requires development of special mining methods, and mine dewatering infrastructure to avoid hazards during shaft sinking and underground development. The costs associated with mine drainage control and Mine Dewatering Systems (MDS) are relatively small compared to the huge consequential losses that can occur in case of an uncontrolled inflow and subsequent flooding of the mine. The design of MDS needs consideration of accurate prediction of the maximum uncontrolled inflow rate, availability of the system during an uncontrolled inflow while the inflow is mitigated, and decision on pumping system technology to have capability to operate under water. The research presented in this paper provides a theoretical framework for a reliability based design procedure which takes into account the uncertainty in the estimate of the maximum uncontrolled inflow, performance of the system during the period of an uncontrolled inflow and a methodology to decide on appropriate pumping technology considering the reliability of the system and available underground storage. The reliability based mine design procedure integrates the ideas of Effective Reserve and Hydraulic Reliability Index to come up with a unified methodology for design of Mine Dewatering Systems.

Aug 1, 2010

"These standards were developed by the CIM for use with the value or worth of a Mineral Property as opposed to “evaluation” where the key objective is an economic assessment or determination of the economic merit of a propertyP1 .0 BACKGROUNDPl.1 There are at present no comprehensive standards for valuation of Mineral Properties in the Canadian mining industry. The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) specifically recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties.Pl.2 On May 5, 1999 at the Calgary Annual General Meeting, CIM Council approved the formation of a Special Committee on Valuation of Mineral Properties (CIMV al) to be co-chaired by Keith Spence (Chairman of the CIM Mineral Economics Society) and Dr. William Roscoe (Roscoe Postle Associates Inc.).Pl.3 The mandate of CIMVal is to recommend Standards and Guidelines for Valuation of Mineral Properties to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges.Pl.4 The members of CIMVal represent of a mix of professional disciplines and experience in the field of Mineral Property valuation:Keith N. Spence (Co-chair), Alliance Pacific Resources Inc., TorontoWilliam E. Roscoe (Co-chair), Roscoe Postle Associates Inc., TorontoMichael J. Bourassa (Secretary), Aird & Berlis LLP, TorontoChristopher R. Lattanzi, Micon International Limited, TorontoRoss D. Lawrence, Watts, Griffis and McOuat Limited, TorontoPaul E. Lunney, Noranda Inc., TorontoCraig A. Roberts, Pacific International Securities, VancouverDavid A. Scott, CIBC World Markets, TorontoIan S. Thompson, Derry, Michener, Booth & Wahl Consultants Ltd., VancouverWilloughby A. Trythall, retired Placer Dome executive and consultant, Vancouver"

Jan 1, 2003

An essential tool for every step ? Early field survey ? Handheld satellite phones ? Portable satellite phones ? Exploration and Drilling ? Handheld satellite phones ? Portable satellite phones ? Production ? Handheld and portable ? Fixed Satellites systems ? Asset tracking systems Main applications via satellite ? Voice and Fax communication ? Internet access and E-mail ? Video conferencing ? Interconnection to mobile phones, 2 way radios, long range WIFI ? Equipment Tele-maintenance ? Telemedicine ? Crew and morale calling ? Vehicle and asset tracking

May 1, 2006

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By A. C. Halferdahl

The Granby ores may be divided into three groups or classes. The No. I ore is a heavy pyrite, chalcopyrite, pyrrhotite, sulphide carrying some free silica, and calcite. No. 2 ore carries the same general group of sulphides as does No. 1, but in a lesser amount. The gangue is an altered greenstone. No. 3 ore has a smaller amount of sulphides than either of the others. Analyses of these ores is as follows: Cu. Si02 Fe. CaO S. Al 203 MgO No. I. Per Cent. 1.8 17.5 33.0 5.7 34.5 2.3 1.3 No. 2 Per cent. 2. 0 35. 6 23. 9 4. 3 I .5. 0 9. 2 6 .. 0 No. 3, Per cent. 1 . 5 40. 9 21 . 7 3. 0 I 1 . 3 11 . 0 5 . 4 The sulphide minerals in No. 2 and No. 3 ores occur largely in bands in the gangue, and for these portions comparatively coarse grinding serves to release the gangue. Drill cores show a certain dissemination of sulphides in portions of the rock, so that grinding to 5 per cent. + 65 mesh with 65 per cent.-200 mesh liberates the sulphide minerals very completely. The association of the sulphides is fundamental. The pyrite was probably deposited first and was followed by a portion of the chalcopyrite, or these two portions of the sulphide minerals were deposited together.

Jan 1, 1924

By A. F. Matheson

"The Jellicoe is the most westerly mine in the Little Long Lac area with a record of gold production. The property is largely covered with overburden and the ore deposit was found by diamond drilling along the projected strike of a gold bearing zone at Magnet lake 1 ½ miles to the east on the property of Bankfield Consolidated Mines, Limited. In 1940-41 Jellicoe mined the whole orebody of approximately 14,000 tons, recovering 5,620 ounces of gold.The vein is in light-coloured greywacke. A mile-long dyke of fine-grained quartz feldspar porphyry 5 to 10 feet in width lies 100 feet south of the vein. A similar, even longer dyke lies 700 to 800 feet north of the vein. Some narrow diorite dykes are also rather closely associated. The porphyry dykes are gold bearing, but not ore. The vein material is quartz and silicified and brecciated greywacke. Mineralization consists of native gold, pyrite, arsenopyrite, and some sphalerite."

Jan 1, 1954

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

By Ron H. Derammelaere

Coal Slurry Test Pipeline and First Recorded Commercial Pipeline Wallace Andrews founder of New York Steam Company awarded patent for ?Method of Transportation? that involved pumping finely divided coal in slurry form built test facility at Madison Avenue and East 58th Street in New York City died in 1899 in a fire and coal pipeline work was not continued First recorded commercial coal slurry pipeline designed by Gilbert Bell in 1914 to move coal from barges on the Thames River in London to a powerhouse in 8? tubes (660 yards long)

May 1, 2013

By Michael R. McPhie

Topics of Discussion 1. The Global Mining Initiative (GMI) and MMSD North America (Brief) 2. Task 2 of MMSD North America ? A Test for Sustainability 3. The Seven Questions and their Application 4. Key Recommendations and Next Steps GMI = Global Mining Initiative Significant international collaborative effort supported by more than 30 of the world?s largest mining/minerals firms which sought to involve all communities of interest. Three major streams of activities: 1. Mining, Minerals and Sustainable Development Project (MMSD) ? 4 regional Process (North America, Southern Africa, South America, Australia) 2. Creation of ICMM (formerly ICME) 3. Major conference in Toronto in May, 2002

May 1, 2002

By H. R. Hammond, E. Sadar

Cominco is making substantial savings in secondary breaking by replacing dynamite with a new nitrate-based explosive. Compareo with dynamite. the new explosive, known locally as "Fine NCN," is significantly cheaper, more effective and safer to use. It also works better than prilled NCN, which is unsatisfactory for secondary blasting because of inadequate sensitivity, low strength and awkward handling properties. A simple apparatus has been devised for pulverizing prilled NCN to a fineness practical for effective secondary breaking. Blasting systems using cheap detonating cord for initiation have been developed.

Jan 1, 1966