Search Documents

By T. W. Wong, M. A. Whitney, A. Hadadzadeh

Uniaxial compression tests were performed on cylindrical specimens, 10mm in diameter and 15mm in height, machined from an extruded AZ31B magnesium billet. The tests were conducted under isothermal conditions to a true strain of 0.5. The study compares macroscopic flow anisotropy between the extruded (ED) and transverse (TD) directions in the temperature range of 300°C to 500°C, and strain rate range of 0.001s-1 to 1s-1. Compression of ED specimens at low strain rate (0.001s-1) exhibited axisymmetric flow, and no significant differences were observed between geometries of specimens deformed above 350°C under the same strain rate. Deformation of TD specimens at low temperature and/or low strain rate resulted in elliptical cross-sections, with the anisotropy of flow being less significant at higher temperatures. Other studies performed using rolled plates have proposed that pyramidal slip and cross-slip at higher temperature eliminate the effects of initial texture, while the dominance of prismatic slip at lower temperatures will result in anisotropic flow. It is believed that the initial fiber texture common among extruded HCP-structured materials plays a role in the anisotropic deformation behaviour observed in the extruded specimens

Jan 1, 2015

By G. Granata, C. Tokoro, T. Kato

"The goal of this study was to evaluate the effectiveness of mechanochemical activation by planetary milling as method to enhance the recovery of cerium from rare earth ores. For this purpose, a weathered ore was first ground by planetary milling and then leached by sulfuric acid. The influence of planetary milling was investigated by assisting the experiments with X-ray absorption fine structure (XAFS) in cerium LIII-edge and inductively coupled plasma spectrometry to measure the concentration of cerium dissolved by leaching. Results showed that, by increasing the grinding time, although the particle size of the specimen increased due to agglomeration, the recovery of cerium significantly increased. This finding clearly indicated that a smaller particle size actually hinders the recovery of cerium. In particular, XAFS analysis revealed that the longer the grinding time, the more tetravalent cerium could be converted into trivalent cerium and such conversion, also called mechanochemical reaction was beneficial to the recovery of cerium. Based on the obtained results, it was confirmed that approximately 70% of cerium could be recovered by mechanochemically activated leaching of rare earth ores.INTRODUCTION Rare earth elements (REEs) are a group of 17 chemically similar metallic elements comprising lanthanides, scandium and yttrium. Since REEs have various unique physical and/or chemical properties, they have become essential materials for advanced application (Adachi, 2015). REEs used in industry are usually supplied as rare earth minerals. In the last decades, flotation, gravity separation, magnetic separation and leaching have been widely applied to recovery of REEs from rare earth minerals like monazite (Archana, Rekha, Manis, Jitendra, & Jin, 2015). Among these operations, leaching has been widely studied in the recent years to improve the state of the art (Archana, Rekha, Manis, Jitendra, & Jin, 2015; Xiao, Feng, Huang, Huang, Chen, Liu, Wang, & Long, 2016; Farzaneh, Fereshteh, & Ahmad, 2017). Aiming to enhance recovery of REEs from rare earth minerals, a possible advancement of leaching technology could be the mechanochemically activation of the ore by high-intensity milling (Alorro, 2016). In the mechanochemical activation, an improvement of the leaching performances can be achieved through high-intensity milling operations which result into a dramatic decrease of the mineral particle size with a consequent improvement of the physical kinetics of leaching. Furthermore, the high mechanical energy provided to the sample during milling can determine the rupture of the crystal structure of the mineral, thereby transforming it into a more leachable form."

Jan 1, 2017

By W. Hawker, A. M. Ivana

"Pressure oxidation is used to liberate gold from refractory sulphide ore and concentrates with over fifteen autoclaves in operation. Despite the importance of pressure oxidation, the autoclave chemistry and chemical thermodynamics are not well established. For example, there is no consensus on aqueous iron speciation or stability of jarosite phases. Additionally, there remains questions about basic ferric sulphate formation and stability. In addition to a review of the current state of knowledge, a methodology to study the ferric precipitation reaction and relate the results to chemical thermodynamic predictions is presented which will be used to accurately define the phase boundaries of the iron precipitates in the future (hematite, jarosite and basic ferric sulphate).INTRODUCTION With declining availability of orebodies that respond to simple leaching conditions, pressure oxidation has become a prevalent technology to liberate gold locked in sulphide mineral matrices. Gold pressure oxidation was established 32 years ago, with McLaughlin being the first facility in 1985 (Thomas & Pearson, 2016). Pressure oxidation is carried out at elevated temperatures ranging from 180 to 240°C as shown in the summary of operations in Table 1 (Ruonala et al., 2016; Fleming, 2010).A considerable amount of research has been done to study iron solubility and precipitation under autoclave conditions (Tozawa & Sasaki, 1986; Umetsu et al., 1977; Sasaki et al., 1993; Fleuriault, 2016; Cheng & Demopoulos, 2004; Papangelakis et al., 1994; Yue et al., 2003). These reports provide a description of the process chemistry and iron behaviour in the autoclave. However, there remain questions about the type and stability of aqueous species and solid phases. This detailed information is required to build a robust chemical thermodynamic model of the system, allowing for equilibrium and kinetic reaction limitations to be discerned."

Jan 1, 2017

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By Haibin Ma, Jie Song, Qingyou Han, Xiaoming Wang, Wei Vian

In the grain refinement of aluminum, Al3Ti and TiB2 particles are introduced to reduce the casting grain size down to 200 micrometer level, which makes cold working possible. The particles are brought in by the addition of Al-Ti-B type master alloys. It is generally believed that TiB2 particles are stable and nucleate a-Al grains in solidification in the presence of extra titanium than the stoichiometry of TiB2 from the dissolution of Al3Ti particle in the master alloys. Titanium in solution either form Al3Ti layers on the surface of TiB2 particles or as solute to promote the nucleation and to restrict the growth of a-Al grains. However, a consensus on a grain refinement mechanism is still to be reached due to the lack of direct observation. This paper presents finding on the TiB2/Al3Ti interfaces in an aluminum matrix. It demonstrates a strong epitaxial growth of Al3Ti on the surface of TiB2 particles, a sign of the formation of an Al3Ti layer on the surface of TiB2 particles in grain refinement practice. The Al3Ti layer has a crystal coherency with a-Al and hence offers a substrate for heterogeneous nucleation of a-Al grains.

Jan 1, 2015

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By Saikat Chatterjee, Xintong (Brett) Liu, Kinnor Chattopadhyay

Magnesia carbon bricks are commonly used in BOFs and are generally pre-heated before the BOF goes into service. Owing to very stringent emission regulations, the BOF pre-heating process need to be controlled and optimized so that, the emission standards are met. One of the major concerns in organic emissions are its stringent limits on emission rates and total volatile emissions. In the present work, an attempt has been made to integrate CFD and Thermodynamic models to predict the emission rate of volatile organics during the pre-heating process. A one dimensional heat transfer model was developed using visual basic and then integrated with thermodynamics calculations using FactSage 6.4. The parameters that affected organic emissions were the pre heating procedure, gas composition of the burner, heating rate and type of the burner. Typical composition of MgO-C bricks and binder materials were obtained from literature and vendor data sheets. Chemical reactions between organic materials, refractory and burner gasses were considered. The model predictions indicated that certain burner conditions could destroy all organics before it exits the vessel while other conditions needed the use of an after burner at the mouth of the vessel. The model was also able to predict the organic emission rates based on the chosen pre-heating profile. This kind of predictive model will be very useful for the steel industry and enable them to justify permit limit applications and stick to the limits by fine tuning their pre-heating process.

Jan 1, 2015

By P. Chu, J. A. Finch

The formation of small bubbles in flotation is usually accomplished by the use of frothers, or sometimes is due to the presence of inorganic salts in the process water. The effective mechanism associated with the presence of these solutes is generally considered to be coalescence inhibition. However, recent work has demonstrated that the presence of frothers and salts also reduces the size of bubble at the initial formation stage. In this paper we adapt the same experimental setup to investigate the time that it takes for a bubble to form; for a known system power input, the energy to form a bubble can then be estimated from the time. The hypothesis is that the presence of frother and salt will reduce the time for a bubble to form, which can be interpreted as an added energy component being derived from the solute. Testing different types and concentrations of frothers and salts, the hypothesis is supported: the mechanical energy required to form a bubble decreases by about 10% in the presence of these solutes.

Jan 1, 2015

By Y. Thibault, L. Morin, R. Cameron, D. Gould

"There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite tailings in the Sudbury area alone, with an average nickel grade ~0.8% (plus cobalt). Pyrrhotite is a highly reactive sulphide mineral that has the potential to generate acidity; consequently, it is stored in large tailings ponds that require perpetual treatment to avoid the production of acidic drainage. Re-processing this material using bioleaching technologies has the potential to recover valuable metals, while reducing the toxicity, reactivity, and acid generating potential of the remaining residues. CanmetMINING is currently developing a stirred-tank bioleaching process to recovery nickel and cobalt from pyrrhotite-rich tailings. Stirred-tank experiments have been conducted with one tailings sample over a range of pH and temperature conditions, resulting in 80 to 90% and 70 to 80% leaching of nickel and cobalt respectively in 10 days.INTRODUCTION Sulphide tailings may represent a significant financial liability for mining companies as these wastes may produce acidic drainage under some disposal conditions. As a result, the companies must post financial bonds large enough to ensure there are sufficient funds for perpetual management of these wastes. At the same time, there are billions of dollars in metals incorporated into these mining wastes waiting to become valorized. Many sulphide tailings are amendable to bacterial oxidation for metal extraction. Re-processing of tailings using bacterial leaching has the potential to recover valuable metals from waste; and reduce the toxicity, the reactivity, and the acid generating potential of the remaining residue. By reprocessing these wastes there is an opportunity to significantly reduce liabilities and financial assurance bonds, while recovering metal values. There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite-rich tailings in the Sudbury area alone with an average nickel grade ~0.8% (Peek et al., 2011) plus cobalt and copper. Pyrrhotite is separated from pentlandite concentrates by magnetic separation and flotation. It is already finely ground and has often been segregated from other tailings material, making „mining? relatively inexpensive. This represents roughly (> $100/ton) in contained value, with negligible mining costs. This paper reports on the development of a stirred-tank bioleaching process for recovering nickel and cobalt from pyrrhoitite-rich tailings, which is currently underway at Canmet MINING."

Jan 1, 2017

By M. A. Halim, V. I. Lakshmanan, Z. Jankovic

An innovative mixed-chloride process for the separation of iron from lateritic ore is described. The separation of Fe(III) from leach liquor is an important process step for the recovery of nickel and cobalt. The patented process of Process Research ORTECH Inc. uses a lixiviant containing hydrochloric acid (HCl) and magnesium chloride (MgCl2) for the leaching of lateritic ores/concentrates followed by the selective solvent extraction step of Fe(III) over other value metals such as Ni and Co. The use of MgCl2 increases the activity of the hydrogen ion in the lixiviant, which reduces the consumption of HCl in the leaching stage and enhances the formation of HFeCl4-, thereby increasing the solvent extraction efficiency of Fe(III) with ketone. The process produces high purity iron oxide (Fe2O3) and regenerates HCl by the pyrohydrolysis of the FeCl3 rich pregnant strip solution. The developed process flowsheet is in closed loop, economically attractive and environmentally friendly.

Jan 1, 2015

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously 'based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By Dorothy Walters

As an increase in the number of producers alters fact ors affecting supply, long-term prospects in traditional markets for many minerals weaken. At the same time, conflicts between national and international objectives undermine existing competitive elements in mineral markets and Canadian costs escalate. Such changes may dramatically alter the environment in which the mining industry operates.

Jan 1, 1979

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By T G. Callcott

Australian coking coals are either class 434<tlj534<2l, at Port Kembla, or 634<3> at Newcastle. The former yield good blast-furnace cokes; the latter yield poor ones. However, increases in conventional strength indices, by methods applicable with normal coking ovens, seem unlikely to be economically attractive. Characterization of the coals has enabled an "economic" blend to be developed in the Newcastle area, and this has affected mining, preparation and handling operations. Coking studies have led to a specification for the making of strong coke, especially from the high-volatile Newcastle coals. Continuous coking studies, developed from the efforts to make very strong coke, have taken two directions. Firstly, coking thin layers of coal on strands; secondly, coking, in various types of vessels, compacts of coals with or with-out the inclusion of non-coking coals, iron ores or other inert materials. Gas, "sand" and hot metal coking have been tested for use in compact coking. Particular attention has been paid to pellets of coal and ore. The probable industrial problems in adopting any of the ideas are presently being examined.

Jan 1, 1963

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017