Search Documents

By Edouard Asselin, Tasawar Javed

The precipitation of hematite from ferric sulphate - cupric sulphate - lithium chloride acidic solutions was studied in a batch reactor. The effect of several variables on the extent of hematite precipitation as well as on its crystallinity and purity was investigated. The variables studied include: initial ferric concentration (1.5 - 30 g/L), retention time (0 - 12 h), initial sulphuric acid concentration (0 - 30 g/L), temperature (150 - 220 °C) and chloride concentration (0 - 25 g/L). The results show that hematite is preferentially precipitated at lower initial iron concentrations. Longer retention times increased the fraction of hematite in the precipitates but did not affect its crystallinity to a significant extent. On the other hand, higher temperatures increased the purity and crystallinity of the hematite. At lower acid concentrations hematite and goethite were precipitated. However, only hematite was precipitated when the initial acid concentration was > 12.5 g/L. Better crystalline hematite was formed at lower acidities. Increasing chloride concentration increased the amount of hematite and decreased the amount of iron sulphate hydroxide phases, but did not affect the crystallinity of the hematite.

Jan 1, 2015

By R. L. Bruening, R. M. Izatt, N. E. Izatt, S. R. Izatt

"Molecular Recognition Technology (MRT) is a simplified, green chemistry process with applications in selective separations of Ni(II), Co(II), and platinum group metals in primary ore beneficiation processes and secondary recovery operations from spent products, scrap, and environmental waste solutions. Simplification in MRT processes is achieved by non-use of solvents, reduced space requirements, and a simple separation system involving columns packed with metal-selective SuperLig® resins. Minimal waste is generated and metal recovery is achieved at 99% levels from g L-1 to <mg L-1 concentrations. MRT systems are attractive technologically and economically compared with solvent extraction, ion exchange, and precipitation separation processes. Commercial examples of MRT use include removal of impurity metals Cd, Cu, Ni. Fe, and Pb to mg L-1 or lower concentration levels from Co streams to produce battery-grade Co. Highly purified Co is required for optimal function of lithium ion rechargeable batteries and superalloys associated with aerospace and gas turbine operations. Impurity metals are recovered for reuse or proper disposal rather than being discarded to landfill. Green chemistry processes, such as MRT, are needed in metal separations going forward into the 21st century to achieve global metal sustainability in processing of native ore and treatment of secondary sources.INTRODUCTION Maximizing efficiencies of metal separations and optimizing metal recovery rates during separation processes are important goals on the road to achieving metal sustainability. Achievement of these goals is consistent with stated principles of green engineering (O'Connor, Zimmerman, Anastas, & Plata, 2016) and green chemistry (Anastas & Eghbali, 2010). Molecular Recognition Technology (MRT) separation processes using SuperLig® resins have a 25-year record of performing competitive, commercial metal separations with metal recovery rates approaching 100% (Izatt, Izatt, Izatt, Krakowiak, & Bruening, 2017). SuperLig® resins are characterized by high selectivities for specific metals over concentration ranges from g L-1 to mg L-1 or lower. MRT systems use no solvents and are simple in design and operation resulting in reduced capital and operating expenses."

Jan 1, 2017

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By Harry F. Weaver

WHEN 1 was assigned by the Director of the United States Bureau of Mines to present a paper at this annual meeting of the Mining Society of Nova Scotia, 1 was grateful, honoured, and elated to realize finally a life-long desire to see your beautiful land and visit with you who have the good fortune to live and work here. Naturally, in preparing for this important event, 1 wanted to give you something of special interest within the limits of the subject so I chose an area dose to my heart -the operation of our Federal coal mine inspection service, which has, as its fundamental purpose, the prevention of accidents in and around ?Coal mines. In 1957 the United States had 10,879 active coal mines scattered throughout 28 States and the Territory of Alaska. The production of coal for the year was about 515,472,000 tons, including 2.5,472,000 tons of anthracite and 490,000,000 tons of bituminous coal and Hgnite. Anthracite is mined principally in a comparatively small area of one State. AU the 28 States and the Territory produce bituminons coal and/or lignite. The beds mined range from 18 inches to more than 100 feet in thickness and from the horizontal to the perpendicular.

Jan 1, 1958

By H. Saeedi Ali, A. J. Monhemius

"Anglo Asian Mining’s Gedabek mine is situated in the Lesser Caucasus mountains in Western Azerbaijan. The ore body is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold and copper-bearing ores. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions. Ore processing at Gedabek is by agitation leaching for high grade ore (>1g Au/t) and heap leaching for lower grade ore. In order to cope with the high copper concentrations in the cyanide leach liquors, a unique combination of resin-in-pulp for selective gold extraction and SART processing for copper removal and cyanide recovery is used. In 2015, a flotation plant was added to treat the tailings from the agitation leach plant before the tails are sent to the tailings dam. This plant produces a copper sulphide flotation concentrate and also recovers some of the residual gold and silver in the tailings. Since February 2017, due to lower grades of gold and higher copper in the feed ore, the decision was taken to alter the flow sheet and to carry out flotation ahead of agitation leaching, to reduce the cyanide consumption during leaching by removing soluble copper minerals. The paper compares and contrasts the performance of the plant in the two configurations, namely, (i) leaching followed by flotation and (ii) flotation followed by leaching.INTRODUCTION In May 2009, Anglo Asian Mining started open pit mining for gold on its Gedabek property in the Lesser Caucasus Mountains in western Azerbaijan. Gedabek is situated on the highly mineralized Tethyan Belt that runs from the Himalayas to the Balkans. The ore body at Gedabek is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold-bearing ores. The sulphidic ores contain mainly pyrite and chalcopyrite, with some secondary copper sulphide minerals, such as bornite and chalcocite, and minor amounts of sphalerite, galena and tetrahedrite. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions and passivation of free gold."

Jan 1, 2017

By V. G. Papangelakis, T. Clark, G. Kolliopoulos

Sustainability of the hydrometallurgical industry requires the development of processes for effective water recovery; if process water is recovered and recycled, fresh water intakes will be reduced. Forward osmosis (FO) is an innovative membrane process that promises to recover water from industrial process aqueous streams or seawater with less energy input compared to reverse osmosis (RO) and evaporation; the energy efficiency relies on the spontaneity of the process (no energy input required). The driving force of the process is the osmotic pressure gradient between a dilute feed solution (process water) and a concentrated draw solution. The draw solution is an engineered aqueous solution that contains a highly soluble chemical reagent that is able to osmotically "draw" only water from the dilute stream, through a semi-permeable membrane, leaving behind a small volume of concentrated brine. The draw solute is separated and recovered for reuse, leaving behind water. The main energy requirements of the FO process arise from the separation and the regeneration of the solute chemicals from the diluted draw solution. This work focuses on the evaluation of aqueous carbonated trimethylamine (TMAH:HCO3) as the draw solution and reports recent findings on the separation efficiency of TMA and CO2 from the solution.

Jan 1, 2015

By Pura Alfonso, Teresa Escobet, Hernan Anticoi, Eduard Guasch, Josep Oliva, Sarbast A. Hamid

"The liberation modelling of mineral particles using mineral liberation analysis have been used in the past to model comminution and concentration processes. In this work this concept has been taken a little further, using comminution and concentration for applying the mineralogical characteristics of particles. This approach is shown using the image analysis, mineral liberation analysis and the distribution density functions for liberation modelling. The work focused on the effect of comminution on mineral liberation for liberation modelling. To model this, effect the mineral liberation of the particles using distribution density and the cumulative distribution was linked to the image analysis of the ore particles. These properties have been estimated by statistical measures such as the distribution density and liberation grade, which were extracted from MLA data and images analysis, using proper image analysis and techniques based on MATLAB software. A comparison of different tungsten ores of liberated particles, has been introduced and evaluated by estimated results and image analysis.INTRODUCTION The chief economic minerals of tungsten are wolframite [(Fe,Mn) WO4] and scheelite(CaWO4), and approximately two-thirds of the world tungsten reserves consist of scheelite deposits (Lassner and Schubert, 1999). Tungsten has unique properties and is widely used in various industrial high strength and high temperature applications. It occurs coarsely aggregated in low grade ores. Most of tungsten ores, particularly scheelite, wolframite and ferberite, occur in deposits with very low content of WO3 (0.1–2.5%) that is not economically viable to apply directly metallurgical methods to extract tungsten (Martins, 2014). Tungsten is considered as a critical metal by the European Union by the economic importance and also the high supply risk (European Commission, 2014; Chakhmouradian et al., 2015).Currently, scheelite is playing an increasingly important role in tungsten industry because the mineral reserve of wolframite is getting depleted after gradual exploitation and utilization (Min et al., 2016). In mineral processing, the liberation of valuable mineral from the gangue determines the efficiency of subsequent separation processes. The liberation characteristics of an ore are primarily dependent on its texture, the association of mineral in the host matrix of gangue minerals, and to some extent on the grinding process (Zhang and Subasinghe; 2013)."

Jan 1, 2017

By F. Henríquez, V. Iriarte, L. Vinnett, J. Yianatos, F. Díaz

Metallurgical characterizations of the collective (Cu/Mo) and selective flotation plants were carried out in Minera Los Pelambres, Chile. The selective plant allows the valuable minerals of Cu and Mo to be separated. The evaluation involved two surveys consisting of metallurgical sampling as well as residence time distribution (RTD) measurements to determine load distribution. The RTD data were obtained in real-time by means of the radioactive tracer technique. In addition, metallurgical data was reconciled and supported by effective residence times. In the collective plant, a performance comparison of parallel rougher circuits was carried out, which included a bank of six mechanical cells of 250 m3 and banks of nine mechanical cells of 130 m3. In the selective plant, the Cu and Mo evolution along the plant was evaluated. The results in the selective plant allowed for performance evaluation of mechanical and pneumatic cells in primary flotation. In both plants, mineral losses were evaluated and their relationship with circuit configuration (cell types and circuit layout) was determined. The metallurgical characterization was a powerful tool to evaluate circuit performance and to detect improvement opportunities at industrial scale.

Jan 1, 2015

By M. Sukhram

In the year 1992, T.A. Utigard published a paper titled "The measurement of the heat-transfer coefficient between high temperature liquids and solid surfaces." In that work, he instrumented an agglomerate of materials with thermocouples to infer the heat transfer coefficient of a high temperature liquid on a solid. The purpose of that research was to help in the design and operation of metallurgical reactors. Since that time there have been many researchers that have worked to characterize heat, mass, and momentum transfer phenomena in high temperature metallurgical processing operations. This paper presents results from the author’s experience with instrumenting thermocouples in copper elements coated with carbon to infer velocity of high temperature liquid metals. It also presents a methodology to determine velocity of a high temperature liquid by inferring the local heat transfer coefficient at a solid-liquid interface

Jan 1, 2015

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

By G. Cailletaud, I. Guillot, D. Larouche, R. Martinez, D. Massinon

The precipitation of Al2Cu particles in a 319 T7 aluminum alloy has been modeled. A theoretical approach enables the concomitant computation of nucleation, growth and coarsening, based on an implicit scheme using the finite differences. The equation of continuity is discretized in time and space in order to obtain a matricial form. The inversion of a tridiagonal matrix allows us to determine the evolution of the size distribution of Al2Cu particles at t + dt. The fluxes of solute in-between the boundaries, as well as the ones at the boundaries, are computed in order to respect the conservation of the mass of the system. The main results of the model are compared to TEM measurements. Simulations provide quantitative features on the impact of the cooling rate on the size distribution of Al2Cu particles in good agreement with the TEM measurements. This metallurgical model is integrated into FEA software in order to perform mechanical computations. This kind of multiscale approach allows new perspectives to be investigated in the process of designing cylinder heads. It enables a more precise prediction of the microstructure, its evolution as a function of continuous cooling rates and its impact on the integrity of the structure.

Jan 1, 2015

By A-A. Bogno, M. Rappaz, J. Valloton, H. Henein

"Rapid solidification of Al-Cu droplets of eutectic composition was carried out using Impulse Atomization in an argon atmosphere, to study the microstructures forming at different cooling rates and undercoolings. Two distinct morphologies were observed within the investigated Al-33wt%Cu droplets microstructures: (i) A regular lamellar morphology and (ii) an undulated morphology. The volume fraction of each type of morphology was measured as a function of the droplet size and the nucleation undercooling was deduced using the hypercooling limit equation. The scale of the microstructures was determined through measurements of inter-lamellar spacing across and along the growth direction. Growth velocity and undercooling were deduced using Jackson and Hunt (1966) eutectic growth theory. Finally, mechanical properties were estimated through micro-hardness analysis using a Vickers hardness tester, revealing exceptional properties for an aluminum-copper alloy. Indeed, the hardness values, increasing with growth rate and undercooling, were 3 times higher than the values obtained in hypo-eutectic Al-Cu alloys.INTRODUCTION Eutectic alloys are very attractive due to their good fluidity allowing ready shaping of parts in casting processes as well as in thermal spray deposition. In addition, they yield microstructures with high mechanical properties, by the virtue of their scale/size which is defined by the solidification parameters and the thermodynamic and thermophysical properties of the given alloy. Therefore, it is important to understand the relationship between the microstructures and the solidification parameters of eutectic alloys in order to control their solidification path and mechanical properties. The latter could be improved by either adding an appropriate strengthening component to a base eutectic material (Böyük, MaraslI, Kaya, ÇadIrlI, & Keslioglu, 2009) or by refining the microstructures for more effective dislocation pinning (Campbell & Campbell, 2003). Tailoring the microstructure can also be beneficial to chemical (Freitas, Osório, Spinelli, & Garcia, 2014; Osório, Freire, Caram, & Garcia, 2012) or electrical (Kaya, 2012) properties of the material. Eutectic-type microstructures, usually formed from liquid (eutectic transformation) or solid (eutectoid transformation), are made up of two or more different phases, generally of lamellar or fibrous (rod like) morphologies (Kurz & Fisher, 1998). In general, a binary eutectic structure can be regular (when both phases are non-faceted) or irregular (one of the two phases is faceted), the two solid phases having roughly the composition of the liquid from which they are formed."

Jan 1, 2017

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By Zhou Yanwen, Fudong Wang, Shing Liu

Mixed CrB2 and MoS2 powder (Cr:Mo=1:1 atomic %), without any further process, were used as the targets to be sputtered and deposited onto stainless steel and silicon substrates by pulsed DC power supply. The structures and properties of the CrBMoS films were then analyzed by using SEM, XRD, micro-hardness tester. The SEM morphology of the films showed dense, defect free structure, and the preferred orientations of the films were CrB2 (111) and MoS2 (200) according to XRD spectra. The thicknesses of the films were measured and the relationship between the deposition rates and pulsed factors was determined. The films, with the micro-hardness as high as 19GPa and friction coefficient as low as 0.02, could be considered to be the hard solid lubricant films.

Jan 1, 2015

By Yihan Liu, Jintao Zhang, Chen Xiao, Xiaomeng Zhao, Guanglei Song

To estimate the performance of the inert anode materials based on NiFe2O4 spinel ceramic during it used for aluminum electrolysis, we investigated the wetting process of cryolite molten salt which is in composition of industrial aluminum electrolysis with carbon anode and NiFe2O4 based cermet materials, by means of determination the interface wetting angle between the molten cryolite electrolyte and the solid anodes interface. The results show that the wetting angle between the electrolyte and carbon anode is larger than 90 angulation, this means that they basically can not wetting; however the nickel ferrate spinel ceramics behaves much better. In regard to the NiFe2O4 matrix materials, their initial wetting angles is 76.9. The initial wetting angles for 1.0wt%MnO2, 2.5wt%TiO2 and 0.5wt%V2O5-doped samples are respectively 56.86°, 52.98° and 51.93°. However, after 50s later, all the wetting angles came down below 15°.

Jan 1, 2015

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017