Search Documents

By J. C. Kurnia

Methane is recognized as one of the prime causes of underground mine disasters around the globe. A cost-effective mine ventilation system and methane control is required to ensure a safe and productive environment in an underground mine whilst keeping energy usage and operating cost at minimum. Typically methane enters a mine environment or tunnel from localized distributed sources at high initial concentration. Hence, an understanding of its dispersion from discrete sources is important to design a methane management system via effective ventilation. This study employs computational fluid dynamics to model methane dispersion in an underground tunnel which has a number of discrete sources of methane and effective ways to dilute and or disperse it. Air flow distribution within the tunnel as well as methane dispersion is simulated by solving the governing transport equations subject to appropriate boundary conditions. First, the effectiveness of ventilation duct placement is examined. Several possibilities are explored and investigated. It is found that the common configuration utilized in underground mine performs best as compared to other configurations in maintaining the concentration of methane below permissible levels. Next, a novel intermittent airflow ventilation system is proposed and evaluated via simulation with the goal of reducing the energy cost whilst maintaining methane level in the mining face below the allowable level. Parametric studies are conducted to investigate effects of various factors influencing the effectiveness and performance of this novel intermittent ventilation system. This study will provide some new ideas for designing an efficient and effective underground mine ventilation system by lowering the net average amount of air that needs to be circulated in the tunnel for a safe operation. KEYWORDS

Aug 1, 2013

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By Anthony T. Eyton

Intelligent Systems: Advantages for Mining ? Increased safety (reduced risk to workers) ? Increased productivity (reduced downtime) ? Reduced maintenance costs ? Customized solutions for different mines ? Growing acceptance among mine managers A Typical Precarn Project ? Meets definition of intelligent systems ? Involves at least two Precarn members ? a technology developer partner and a user partner ? in a true collaboration ? Involves at least one university and may have various other players ? Leads to a demonstrated prototype ? Costs $2-4 million, and lasts 12-30 months ? Gets up to 40% of its funding from Precarn (max. $1 m) ? Produces new intellectual property -- owned by the project team

May 1, 2002

By L. E. Gutiérrez

A new filtration model based on porous media transport theory is presented. It predicts capacity and final moisture content in the filtered cake as a function of design and operational variables at the plant. FilterSim® is the computer code where this new model is programmed. Application of FilterSim® to ten-month operation of an industrial copper concentrate filtration plant is shown on a daily basis and using a single set of internal parameters for the whole period. Average error is less than 5%, both in capacity and moisture estimation. FilterSim® abilities to optimize industrial filtration plants as well as to estimate future budgets are illustrated with several real examples.

Jan 1, 2007

By Deni Côte, Michel Dagbert, Marcel Vallée

"Greater reliability of mineral deposit and reserve estimates can be attained through better quality control of the data and information acquisition, and the estimation processes. This paper reviews the following key requirements:1. greater awareness of the significant figures of both data and estimates, and better understanding of the probabilistic aspects of the estimates, their confidence limits and margins of error;2. greater reliability of the information that supports the estimates, by more explicit and more rigorous methods and standards for data acquisition and for interpretations;3. more quantitative estimations of geological/mineral continuity, based on improved three dimensional sampling patterns and the use of geostatistics; and 4. better integration at the project engineering and mine production stages, of the mineral deposit characteristics and mining method constraints, for more efficient mineral recovery and mine quality control.RÉSUMÉUne plus grande fiabilité des estimations des gisements et des réserves minières requiert plus d'emphase sur le contrôle de la qualité de I ‘acquisition de l'information et du processus d'estimation. Les exigences suivantes sont revues:1. le respect du niveau d'exactitude des données et des estimes en n'utilisant que le nombre approprie de chiffres significatifs des observations et mesures, et en exprimant le niveau de confiance et la marge d'erreur des estimations;2. l'amélioration de fa fiabilité des données par des normes plus rigoureuses pour leur acquisition et leur vérification, et par des méthodes plus systématiques d'interprétation et de modélisation;3. l'estimation plus rigoureuse de la continuité des minéralisations dans les trois dimensions des gisements, par des patrons échantillonnages mieux adaptes awe paramètres géologiquement minéralogiques, et par l'utilisation des méthodes géostatistiques; et4. l'intégration plus poussée, particulièrement lors de la planification de l'exploitation minière, des caractéristiques des gisements avec les contraintes des méthodes d'exploitation, pour améliorer la récupération et le contrôle de la qualité en exploitation."

Jan 1, 1993

By Ting An Zhang, Chengzhi Jiang, Xiujing Zhai, Feng Xie

The extraction and concentration of nickel from aqueous solutions by emulsion liquid membranes (ELMs) using tributylphosphate (TBP) as extractant has been investigated in this research. The emulsion liquid membrane consists of a diluent (kerosene), a surfactant (Span 80), a mobile carrier (TBP), and a stripping solution (ammonia solutions). Important factors influencing the separation process including membrane composition, feed composition, and mixing speed have been examined. The results show that more than 90% of nickel in the feed solution could be extracted by ELMs under the experimental conditions, indicating the feasibility to use the designated ELMs to detoxify nickel-containing industrial waste solutions.

Jan 1, 2014

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By Nancy C. Mohn

?Even though the age of many existing coal units exceeds 30 years, these units continue to perform with excellent reliability and at a competitive cost with other fossil fuel units. ?NERC data shows a consistent increase in availability for all utility coal generation ?With the opening of power markets, the challenge for coal is to produce competitive electricity while meeting increasingly stringent, and costly environmental limits. ?During the 60s and 70s, subcritical steam power plants dominated the market. The emphasis was on scale-up to larger MW size units. ?In the last decade, we have seen interest in a broader set of technologies with new drivers: ?Fluidized bed technology was developed to respond to increased environmental requirements, particularly with lower quality fuels ?Supercritical pressure units have gained interest for both fuel cost savings and reduced emissions due to higher efficiency.

May 1, 2001

By W. H. White, A. J. Sinclair

"Unaltered biotites from three samples of monzonite and gabbro from the Copper Mountain stock and a single sample from a pegmatic biotite-chalcopyrite vein cutting the Triassic Wolf Creek formation have a mean K-A age of 193±7 m.y. These data support a suggestion based on geological evidence that Copper Mountain ore deposits are related genetically to the Copper Mountain stock.A cogenetic mineral pair (biotite and clinopyroxene) from a sample of sericitized and chloritized monzonite of the Copper Mountain stock have identical K-A ages of 150 m.y., which probably represents a time of wide-spread, post-ore, hydrothermal alteration. This alteration is believed to be related genetically to a group of post-ore intrusions known as the ""mine dykes,"" suggesting that they also have an age of 150 m.y."

Jan 1, 1968

By Silvio E. Kruger

Real time measurement of wear and corrosion provides crucial information needed to determine an optimal schedule for corrective maintenance and is a powerful tool to maximise equipment availability and reliability. It also leads to savings from optimized spare parts handling and helps to avoid costs of accidents and their negative impact on safety and the environment. This paper presents the technology of ?painted-on? ultrasonic transducers that can be integrated to structures and accurately measure the remaining thickness and therefore determine wear or corrosion losses. These transducers have a small footprint, a performance comparable to other commercially available ultrasonic transducers and can sustain temperatures as high as 400ºC. The application of this technology to mining equipments and its potential benefits are discussed.

Aug 1, 2013

By B. Coupal, F. D'Hennezel

Sorption measurements show that peat moss has much stronger affinity for oil than straw, which is currently used. Microscopic studies of peat moss show a highly porous and fibrous material, and this property, associated with the phenomenon of selective absorption, had been used to absorb oil. Laboratory experiments show that peat moss absorbs up to eight times its weight of oil. Field tests have proved that peat moss can be an effective absorbent and can be used on a large scale.

Jan 1, 1972

By J. M. R. Carvalho, M. T. A. Reis, M. R. C. Ismael, M. J. N. Correia, S. M. C. Santos, J. M. Carvajal

A sulphide zinc concentrate (Zn-40%) has been leached in sulphuric and chloride media to optimize the conditions for the recovery of zinc and copper. Previous results showed that extractions of 95% zinc and 20% copper can be achieved in just one stage, after two hours of leaching at 80°C with a solution 0.5M in Fe2(SO4)3 and H2SO4 and a solid/liquid ratio of 5%. This work presents the results obtained in the leaching experiments carried out in sulphuric and chloride media using two and three crosscurrent stages and a countercurrent process simulation for a solid/liquid ratio of 10%.

Jan 1, 2008

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events, and so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the body of knowledge captured from diverse mining industry experts for the management of unwanted strata incidents, and explosions in the underground environment. This knowledge is divided into a series of initiating events within both topics (as listed) with further degrees of classification based on design, operation, and management concerns. Strata Underground Initiating Events: Explosions Initiating Events Loss of strata control at longwall face Fire or ignition in a sealed area Loss of strata control in outbye roadways Fire or ignition in an unsealed goaf area Loss of strata control in roadways under development Fire or ignition in an extraction face Loss of control of overburden and caving behavior Fire or ignition in outbye Loss of pillar system stability Loss of control of goaf edge in pillar extraction Fire or ignition in a development panel or first working Loss of strata control in shafts The system guides the user in generating substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By Paul Delottinville, Maynard Hall, Henry Hillier

"An expert system application for supervisory control and optimization of the indurating process at the Iron Ore Company of Canada (IOCC) has been developed and installed in closed-loop. Prior to the installation of the expert system, the indurating machine was rebuilt and the instrumentation revamped. A Foxboro I/A Distributed Control System (DCS) was installed for regulatory control, and a new control strategy configured. The modernization of the regulatory control has resulted in significant improvement in both production rate and product quality. Expert system control was implemented in September 1996. Preliminary indications are that the expert system has further improved the consistency of product quality, enhanced fuel efficiency and increased productivity. The expert system considers both wet and dry sections of the circuit, and its optimization scheme is driven by pellet tumble index and compression strength. Statistical Process Control (SPC) rules were implemented in the expert system as part of the quality analysis and control scheme. The expert system application was developed and delivered using the Comdale Expert Optimizer (CEO), and has been in continuous closed-loop control since its installation. The system development and implementation is described, and preliminary benefits are presented..... IntroductionIn early 1996 the Iron Ore Company of Canada (IOCC) contracted Comdale Technologies of Toronto to develop and implement a real-time expert system for optimizing the indurating pelletizing furnace at our plant location in Labrador City, Newfoundland.The decision to install the expert system has been timely. Like many other resource-based industries in increasingly competitive markets, IOCC recognizes the need to find ways to improve the efficiency of our production process and ensure that product quality is maintained at the highest levels. With the Labrador City plant producing 11 million tons of iron ore pellets annually, implementing the best technology solutions to meet these objectives is critical."

Jan 1, 1998

By Graham Swan

The case is presented for the development of a spray-on liner for ground support, but only in the context of a new mining system, consistent with the technical and business case advantages of liners compared to alternatives. Over the past 10 years much effort has been expended in specifying and testing the mechanical/environmental properties of various liners, without actually fulfilling any mining system requirements. The results have been generally disappointing, with no consistent and sustained application in a dayto- day production environment being achieved, anywhere. Central to this shortcoming has been the failure of mining/liner ma nufacturing companies to realise that screen/mesh or shotcrete cannot simply be replaced with thin, deformable liners: success will depend upon closely defining and evolving a new, liner- functional mining system. The paper begins with a discussion of some fundamental technical capabilities and constraints associated with 3M Canada?s liner material that has been developed in partnership with Falconbridge Limited. Intended applications for this liner include the support of bursting ground associated with deep mining conditions. With safe application and consistent performance in mind, the paper argues for a new mining system that derives in the first place from best quality drilling and blasting practices. Taking this as a given, a system for waterscaling and liner application prior to mucking out is proposed, followed by bolting through the liner while arranging for the bolts to be explicitly connected to the liner. Some logistical and equipment related challenges of such a mining system are then reviewed and discussed in the context of the business case for liners. It is concluded that this approach, if successful, will provide the greatest benefits in the areas of safer mining, due to reduction in worker exposure, and in reduced mining cycle times.

May 1, 2003

Adaptive Processing as proposed in geometallurgy has to rely on spatially interpolated information on geometallurgical parameters like phase composition, size distributions of particles of different phases, grain shape parameters, and portions of value elements in different grains. Using the geostatistically predicted values for adaptive processing, e.g. for the selection of milling diameters, thresholds in physical separation, or choices on using an extra pre-separation step, is typically not optimal. Mathematically this effect is introduced by two forms of nonlinearities: 1) The nonlinear scales of compositions, distributions, and shapes have special properties with respect to geostatistics. Classical geostatistics creates some artefacts for these nonlinear scales. On the other hand, modern geostatistical procedures adapted to these scales do not provide unbiased results with respect to linear transformations of the data (e.g. biased block estimates). 2) Neither economic nor ecological effects (e.g. monetary gain) of processing decisions are linear in the interpolated geometallurgical parameters. These nonlinear transforms are not unbiasedly estimated by the likewise transformed unbiased geostatistical predictions of the geometallurgical parameters. Furthermore, we need to optimize the conditional expectation of the gain, rather than obtain an unbiased estimate. Standard geostatistics as such does not provide the "right sort" of estimates for adaptive processing. A nonlinear kriging procedure is needed to approximate the nonlinearities mentioned before. We propose to solve these problems simultaneously using a nonlinear geostatistical technique for predicting the target function (the monetary gain), rather than to predict the geometallurgical parameters and compute the gain from them. The optimization can then be performed directly on this estimated function. It can be shown that this optimization performed on the conditional expectations, not on unbiased predictions, would yield the best possible processing choice. We propose a procedure choosing the processing parameters on an approximation of the conditional expectation. The difficulties with the classical approach and the effectiveness of this new approach are illustrated by a simplified simulation example with a single processing parameter and a simple dependence on the microstructure.

Aug 1, 2013

"The ore currently being milled at Delnite is a high pyrrhotite ore with the gold intimately associated with the pyrrhotite. To get maximum recovery of the gold with the lowest reagent cost, it is necessary to keep the pH as low as possible In the laboratory the best results were obtained with a pH of 10 but in the plant it was found that a pH of 11 was the minimum practical pH. With the n1anual control it was difficult to maintain this figure.The Mines Branch had a conductivity probe (see Fig. 1), developed by Dr. G .G. Eichholz that they wished to try out in plant operation.On June 17, 1963, the probe with all necessary control equipment was installed in the regrind circuit (see Fig. 2) at Delnite Mines. Crushed quick lime is fed at this point but it is also necessary to feed hydrated li1ne at two other points in the cyanide circuit in order to maintain the pH close to 11. 0 throughout the circuit. Only the feeding of the quick lime at the regrind mill was controlled in this test.One thing that concerned me with the operation of the probe was whether the reading on the probe chart would correspond to the pH. A look at the graph accompanying this paper will show that except for very minor variations the graphs of the chart reading and the pH reading are parallel. The upper graph shows that the pH reading and the lime titrations also correspond and that the cyanide titrations appear to have little effect on the pH reading.Table 1 gives the results obtained for the two months before and after the instal1ation of automatic control as well as the two months of control. Unfortunately there was a decided change in ore just after the automatic controls were removed. There was much less pyrrhotitc in the ore than usual thus changing the need for lime and cyanide."

Jan 1, 1964

By Abdurrahman Tosun

It is very important for after blasting processes that muck pile fragmentation is predicted and controlled during blasting. Therefore, a significant research effort has been devoted to the development of mathematical equations that predict the value of average muck pile fragmentation. The specific charge parameter used in all of these equations is determined as the ratio of the total mass of explosives used to break a volume of rock. The length of blast surface and the row number of the blasthole are ignored in the calculation of the specific charge. However, in a blasting operation, blasthole geometry may result in additional material being impacted by a blasthole. This is due to effect shares of in both end sides of blastholes and the back region of blasting surface. In this study, a total of 14 blast tests, 8 at the first quarry and 6 at the second quarry of the Bati Anadolu (Western Anatolia) Cement Factory, were performed. In each study area blast tests were designed in the same direction continuously to provide stable structural properties of the rock. Therefore muck pile fragmentation depended on only specific charge values for each blast tests. Specific charge values were calculated according to both an average blasthole and also the total volume of material occurred as a result of blasting for each blast tests. During loading until the end of blasted material the front, the back, the arm off and the bucket off pump hydraulic pressure values occurred in hydraulic pistons of the loader were determined with a lot of data received for each blast tests. After that the relationships between specific charges values obtained according to two different methods and hydraulic pressure values of the loader were established with two correlations. The relationships between specific charges values obtained according to the total volume of material occurred as a result of blasting and hydraulic pressure values of the loader occurred as the best results especially the blasting operations that have the total length of blasting surfaces are short.

Aug 1, 2013

By Rodney G. Orr, Phil Robertshaw, Roland Loewer, Klau Lehnert-Thiel

This paper documents the 1988 discovery and subsequent evaluation (to 1991) of diamond bearing kimberlites in the Fort à la Corne area, Saskatchewan, by Uranerz Exploration and Mining Limited. Cameco Corporation began participating as a joint venture partner (50%) in mid-1989. The first indications that kimberlite-type intrusions might exist in the area carne from Geological Survey of Canada aeromagnetic maps. Because of the overburden thickness (over 100 m), magnetometer surveys continue to be the main exploration tool in defining pipe locations and sizes. Magnetometer surveys in varying levels of detail have outlined one main cluster and two sub-clusters, the main group being some 10 km by 50 km in size. In excess of 70 individual targets have been interpreted from the magnetics as probably representing kimberlites. The size range of the individual magnetically-defined bodies is between 1 ha and 74 ha. Proof that the magnetic anomalies were kimberlite intrusions carne in 1989 when each of seven test holes, all drilled on different targets, intersected the potential diamond host rock. The majority of the targets tested were diamond-bearing, with the indicator mineral chemistries suggesting that both peridotitic and ecIogitic diamond parageneses could be expected. To date, 18 individual kimberlite bodies have been drill-tested. A total of 39 bulk samples, amounting to 186 t (representing 360 t of theoretical sample recoveries) were processed in 1990 and 1991. One hundred and sixty diamonds were recovered, averaging 0.04 carats in weight, the largest being 0.6 carats. Most of the bulk sample grades are less than 2 carats/loo t; only three bulk samples have higher grades, the best being approximately 10.5 carats/l00 1. The diamonds are predominantly gem-quality stones.

Jan 1, 1992

By A. J. Sinclair

"Abstract-Geology contributes essential information toward obtaining high-quality resource/reserve estimates. In this context, geology can be considered under the following overlapping topics: regional geology, detailed (deposit) geology, mineralogy, ore deposit models and continuity, with geological mapping being fundamental to all. Each of these topics is considered here in terms of potential contributions to "improved" mineral inventory estimation. Some of the principal conclusions are:1. Regional geological relations must be consistent with deposit geology. It is common that important geological relations are more clearly evident in various regional locales than in highly altered and/or highly deformed mineralized areas containing mineral deposit.2. Detailed geology provides information for a geometric model of a deposit, a model that serves as a basis for mine planning. It is important to distinguish fact from interpretation in such models. Substantial effort is required to characterize the geometric margins of a deposit and the relation of these margins to the simplistic geometric form that normally emerges as an interpretation.3. Mineralogical studies relate to many aspects of deposit evaluation including abundance of ore and deleterious minerals, spatial distribution of ore and deleterious minerals, grain size characteristics of important minerals, mill design, etc.4. Ore deposit models contribute substantially to confidence in developing a three-dimensional geometric model of a deposit for mine planning. Specifically, they are a basis on which to develop rules for interpolation and extrapolation of ore, and they contribute to recognition of domains, each with its own characteristic continuity and margin character.5. Continuity is dependent on mineralization style and may be controlled structurally and/or chemically. It is important to distinguish geological continuity and value continuity. A wide range of classical geological methods are useful in examining geological continuity; value continuity is best viewed as a statistical characteristic that is quantified by any of several measures of autocorrelation."

Jan 1, 1998