Search Documents

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By Wang Xianzheng

For a long period of time, the Chinese Government has been attaching great importance to and supporting the rapid development of the coal industry. Particularly since more than 30 years ago, when China introduced the Reform and Opening-up policy, the reform and development of the Chinese coal industry has witnessed world-recognized achievements. National coal production increased from 618 million tonnes in 1978 to 3.52 billion tonnes in 2011. While China?s coal production accounts for 49.5% of the world?s total, its annual production growth contributes to over 80% of global production growth. China is a country utilizing coal as its main source of energy. As the Chinese Government gives support to the rapid development of new and renewable energy sources, as well as to increased coal utilization efficiency, the ratio of coal in the primary energy consumption mix will gradually decline. However, for a long period of time to come, the total volume of coal demand will keep rising modestly. The Chinese Government has been highly committed to and actively promoting the overall, coordinated and sustainable development model, which puts people first. It has put forward a strategic task to build an ecological civilization, and highlighted its resolve to uphold the basic national policy of resource conservation and environmental protection, with a view to the pursuit of sustainable development. China will incorporate its response to climate change into the national economic and social development program, and take effective measures to lower CO2 emissions 40?45% per unit of GDP in 2020 compared to 2005. At the same time, China will increase the ratio of non-fossil fuels to 15% in the primary energy consumption mix. All of the above factors have raised requirements for the Chinese coal industry, with implications for clear directions, plans and goals for the development of the coal industry.

Aug 1, 2013

By Hökmark. H., M. Lönnqvist

"The Swedish Nuclear Fuel and Waste Management Company are planning to construct a permanent storage facility for high-level nuclear waste at about 500 m depth in fractured crystalline rock. One potential concern for the long-term performance of the repository relates to large fracture shear displacements, since these may damage intersected waste containers. Although details in fracture surface geometries are known to influence slip magnitudes and distributions, fractures are commonly approximated as planar features with lab-scale properties due to lack of relevant field-scale data and to limitations in available modelling tools. The purpose of the work described in this paper is to explore the possibilities to use the distinct element code 3DEC to generate and analyze models with isolated, non-planar fractures and, based on the results of such models, get perspectives on the influence of basic disturbances such as ridges, steps and waves. Given the model set-up, fracture segments with orientations deviating from the critical one will contribute to stabilize the fracture. As a result, all analyzed non-planar fractures slip less than the critically oriented planar fracture. We demonstrate that the angle of deviation is the most influential parameter determining the slip magnitude for comparable surface geometries. Similarly inclined steps and ridges have almost equal slip reductions despite differences in surface area restricting the movement. Although it may be possible to translate the influence of such irregularities to an effective coefficient of friction that could be used as input to models with idealized planar fractures, additional analyses with randomly shaped and distributed asperities, different fracture sizes and with alternative stress loads, need to be carried out to devise a defensible strategy for this type of parameter variation. INTRODUCTIONThe Swedish Nuclear Fuel and Waste Management Company’s (SKB) concept for deep geological storage of high-level nuclear waste is the KBS-3 method according to which the waste will be encapsulated in copper canisters and deposited, surrounded by compacted bentonite clay, in vertical deposition holes at about 500 m depth in fractured crystalline rock (SKB 2011). A site has been selected in the Forsmark area, which is located some 120 km north of the Swedish capital Stockholm. One potential concern for the long-term performance of the repository that has been identified by SKB (SKB 2011) is related to large shear displacements along repository host rock fractures induced by a nearby earthquake, since these may cause mechanical damage to intersected waste containers. Due to lack of relevant data at the appropriate field scale and to limitations in available modelling tools, fractures are commonly approximated as planar features with lab-scale properties. The standard numerical tool, 3DEC (Itasca 2013), used in SKB’s rock mechanics analyses, for example, generates planar fractures by default. Results from dynamic 3DEC earthquake-models (Fälth et al. 2010) currently provide input to layout decisions, i.e., the diameter of the smallest planar fractures that must be avoided when deciding on waste container positions at different distances from potential earthquake faults. It is, however, well known that fracture surfaces are rough or undulating on a wide range of scales (e.g., Candela et al. 2012) and that such deviations from planarity influence the mechanical behaviour of the fractures (e.g., Dieterich and Smith 2009, Marshall and Morris 2012, Ritz and Pollard 2012). It will probably never be a realistic option to attempt to represent the geometrical complexity of a population of fractures of different size, shape and surface structure in any large-scale rock mechanical analysis relevant for the performance assessments of the nuclear waste repository. It may however be possible to find approximate ways to represent different styles and degrees of non-planarity by assigning mod"

Jan 1, 2015

By M Safa

Addressing deficiencies and defects that occur during construction projects is costly and time consuming. The manual quality assurance programs currently used in the industry have certain limitations, including human error and lack of consistency. Hence, there is a need for integrated electronic models that employ new technologies and methods. This research introduces an integrated construction quality control system that has the potential to improve quality management processes in the construction field for piping construction, which is a complex process often requiring rework. The proposed integrated system relies on data collected from construction sites using photogrammetry and laser scanning, which is then used to compare actual work performed to that designed. The proposed system aims to improve the promptness and accuracy of quality assurance processes, in particular dimension measurements, by avoiding human error and integrating defect detection and quality management. The use of this system has highlighted some of the limitations during data fusion and acquisition process, which are highlighted in this paper. These aspects must be considered to increase the reliability of the acquired information.

Aug 1, 2013

By J. Qi

Based on the commercial steel 42CrMo (4140, SCM440), a new generation of CrMo steel was developed by increasing the content of Mo, adding the alloy element of V and Nb, and decreasing the content of P and S. This new CrMo steel has higher strength of 1500MPa and better delayed failure property. TEM and EDS were used to study the distribution and function of the alloying elements in this steel. A new EELS technique was developed to study the bonding strength of the grain boundary in the steel. The mechanism of strengthening of the new steel has been studied.

Jan 1, 2004

By James D. Hall

THIS essay deals with the materials and methods used in the waste filling of scopes in Canadian mines, with especial reference co the methods used at the Sullivan mine, Kimberley, B.C. The author would like to thank members of the staff of the Sullivan mine for information obtained, and acknowledges material from the following publications: Waste Filling of Stopes: Information Circular 6816, U.S. Bureau of Mines. Mining Methods and Practices at Lake Shore, by Leslie S. Weldon; Trans., C.I.M. & M., Vol. XXXIX, 1936, pp. 142-202. Development and Mining (at the Mcintyre Mine), by D. E. Keeley; Eng. & Min. Journal, November, 1933. INTRODUCTION Although mining in Canada is a relatively youthful industry, many of our mines have reached a stage of extraction which requires waste filling, both as a means of support and co make possible the winning of ore that would otherwise have co be left in the mine. Fill may be used at regular intervals as one of the cycle of operations, as in cur-and-fill and square-set scoping; or it may be introduced into a completed stope co provide permanent support for overlying rock formations, and co permit mining of pillars of valuable ore. Waste fill is sorted in resuing, which is a form of cut-and-fill scoping employed in narrow veins.

Jan 1, 1937

By Jesus Garcia Iglesias, Jorge Loredo

"Abstract -The Asturian fluorspar district consists of vein and stratiform deposits where mineralization is controlled by a combination of lithological and tectonic factors.It is postulated that these fluorspar deposits have been formed under disequilibrium conditions created during circulation of ascending hydrothermal solutions along faults and other high permeability conduits. Mixing of solutions is inferred from fluid inclusion studies. Cavity filling and replacement processes are very important in localizing the ore deposits and in determining their morphology.Permian volcanic rocks in the area yield a regional positive geochemical anomaly in fluorine implying that Permian vulcanism may be a possible primary source of fluorine.On a regional scale a relationship can be established between some of the ore deposits and important tectonic lineaments. The stratiform deposits preferentially occur within a calcareous-detrital facies located at the margins of basins. These basin margins are related to important synsedimentary faults.Fluorite is the only economic mineral in these deposits. Quartz, carbonates, barite and pyrite are common minerals accompanying fluorite. Other minerals that may occasionally be present as minor components are: marcasite, chalcopyrite, fahlore, sphalerite, galena and related supergene minerals."

Jan 1, 1994

By W. W. Bake

INTRODUCTION IN IN JUNE, 1943, the main pillars of the Beattie Mine glory hole failed, allowing over a million yards of wet clay and debris to flow into the mine, completely filling all workings to within seventy feet of the 3rd level. The resulting Job of clearing these workings and rehabilitating the mine represents a unique and hazardous operation, seldom, if ever, previously encountered in Canadian mining. The purpose of this paper is to describe one phase of this operation -that of cleaning and rehabilitating the mine from the 6th to the 9th level -to outline briefly the events which led up to this work and to describe the techniques and costs involved. It will be noted that such costs, methods, and performance figures as are dealt with in this paper refer only to work in the internal shaft and adjoining workings from the 6th to the 9th level, previous work having been done under other supervision and management. The Beattie mine is in Duparquet township, northwestern Quebec, twenty miles northwest of the town of Noranda and twenty-three miles southeast of the town of La Sarre. The mine and the town of Duparquet, which it?supports, are accessible by highway from Noranda throughout the year. Production at the Beattie mine began in May, 1933, and up to June, 1943, twenty-one million dollars in gold and silver had been recovered from five and a half million tons of ore.

Jan 1, 1951

By I. Filzwieser, A. Filzwieser

The Peirce Smith converter is the key metallurgical vessel in the majority of copper smelters. During the two step process, oxygen enriched air is injected through a row of tuyeres into the matte received from a primary smelting unit. Additionally, in the first step the iron content is oxidized into a fayalite slag by the addition of silica. During the second step, the remaining copper sulphide is converted into blister copper with a final sulphur content of approximately 200 ppm. The overall efficiency of this process is determined by the total reaction time, the slag quality and quantity, and the chemistry of the final blister copper. To increase the reaction kinetics during both stages, the METTOP Process Control and Regulation (MPCR) system was developed, which consists of four elements: OPC - Optical product control ACR - Automatic computer regulation GCU - Gas control unit GIS - Gas injection system The OPC system from SEMTECH records the optical spectrum emitted by the off gas flame providing immediate, detailed process information. Using this online data, additional gas can be automatically injected into the converter through a gas injection system opposite the tuyere zone. An improved oxygen distribution in the melt and the accurate determination of the process end point results in a significant reduction in the process cycle time. Furthermore, by maintaining the reaction closer to the equilibrium the final sulphur and oxygen content can be reduced compared to the conventional process. In particular, the final sulphur content can be lower than 70 ppm, eliminating the need for an oxidation step in the anode furnace.

Jan 1, 2007

By G. P. Contractor

Many factors affect the forge ability of steels. One of the major factors is chemical composition.' This article discusses the individual effects of alloying elements and the effect of the resultant modification of microstructure onforgeability. INTRODUCTION T HE use of alloy steels is expanding considerably and the fabrication procedures for such alloys are becoming more complex. An attempt is made in this article to describe the effect of alloying elements on the hot-workability of steels. Most of the data reported here are taken from the studies of Ihrig, Clark and others (Refs. 1-4). Chemical composition is not the only controlling factor. Grain size and surface condition of the material, forging temperature, and speed of deformation are also important. Certain conclusions can be drawn regarding the effect of various alloying elements on the hot-work-ability of forging stock. The results of hot-twist tests are considered useful in this connection as the number of twists to failure has been taken as the level of forgeability at a particular temperature. The peak in the "Number of Twists -Tem--

Jan 1, 1962

By Rolf Andreas Lauten, Yanhong Wang, Yongjun Peng

"In mineral flotation, bentonite as a kind of clay mineral imposes deleterious effects on the flotation of valuable minerals, possibly through its ability to increase the pulp viscosity. A higher viscosity lowers the amount of froth and affects the bubble-particle collision frequency. A previous study found that adding gypsum to a bentonite-ore mixture lowered the viscosity, possibly by inhibiting the formation of interconnected network structures. In this study, sulfate as an anion with different types of cations, Na+, K+, Mg2+ and Ca2+ were used to reduce bentonite viscosity and to improve flotation performance. It was found that at the same concentration, MgSO4 was the most effective salt in reducing bentonite suspension viscosity, while CaSO4 was not as effective likely due to the lower solubility of CaSO4. Na2SO4 and K2SO4 reduced bentonite suspension viscosity at high concentration. Flotation kinetics of ore blended with bentonite was increased with increasing the electrolytes concentration, which generally correlated with the reduction of bentonite viscosity. Meanwhile, significant discrepancies were found between flotation results and rheological measurements in the presence of monovalent ions. It is indicated that the morphology of bentonite aggregates in electrolytes solution is likely to influence the hydrodynamics in the froth zone.INTRODUCTIONClay is present in many ore bodies as a gangue mineral. Presence of clay presents several challenges in the processing of valuable minerals. They are soft compared to valuable minerals, which means that during grinding of the ore, clay particles are likely to obtain a smaller particle size than the valuable mineral. Often clay particles may be within the colloidal size domain (<20 µm). The smaller size increases the probability of entrainment in the concentrate. Another challenge is their anisotropic charge distribution, where depending upon the pH, edges (E) and faces (F) carry charges of opposite sign. This facilitates formation of aggregation structures that may impede percolation of bubbles through a froth, but also increase the viscosity more than expected from the mere change in volume fraction. In addition to lowering the froth mobility, a high slurry viscosity will have implications for the gas dispersion in the flotation column as it affects the dispersion of the suspended particles, and it modifies the bubble-particle collision rate and attachment efficiency (Bakker, Meyer, & Deglon, 2009; Shabalala, Harris, Leal Filho, & Deglon, 2011). A pragmatic approach to this problem is to blend high clay ore with ore of lower clay content, reducing the overall clay concentration. Alternatively, one may lower the solids content of the flotation slurry to counteract the viscosity-building properties of clay. While feasible, this approach has the disadvantage of increasing required flotation volume, and it also affects the properties of the froth. Thus, there are currently limited options in lowering the impact of clays and their tendencies to increase viscosity in flotation slurries."

Jan 1, 2016

By Jerry Gagnon, Matt Burr, Timothy Ellis, Abbas Mirza, Larry Webb

"The mechanical properties of RSR anode alloys (lead-calcium-tin, 009+ and lead-strontium-tin) were investigated as a function of time with an objective of developing lead anodes for use in high temperature electrolytic processes such as in copper liberator cells and in cobalt and nickel electrowinning. At a temperature of 70 oC, the mechanical properties of rolled RSR lead-calcium-tin (PbCaSn) alloy currently used in copper electrowinning decreased gradually while the mechanical properties of rolled RSR lead-strontium-tin (PbSrSn) decreased relatively quickly and stabilized at low strength levels. Cast PbSrSn started off as the weakest alloy but its properties remained stable with time. Rolled RSR 009+ anode alloy showed improvement in ageing properties over the other alloys tested. However, its mechanical properties did not stabilize in the study timeframe of 284 days. Further investigations are planned to study the effect of alloying elements on mechanical properties of RSR 009+ anode alloy over several years as a function of time at 70 oC. The mechanical properties will be evaluated to determine the time at which they stabilize. Comparative plant trials with rolled RSR PbCaSn and RSR 009+ will also be performed in copper liberator cells and in cobalt and nickel electrowinning tankhouses to determine their mechanical and electrochemical performance at temperatures of 65-75 oC.INTRODUCTIONLead-based alloys are the primary anodes used in the electrowinning of copper, zinc, nickel, cobalt and manganese from sulfate-based aqueous systems. Lead anode technology has evolved over the years migrating from pure lead and lead-antimonial alloys to the present day PbCaSn alloys for copper and PbAg and PbCaAg alloys for zinc electrowinning (Prengaman, Ellis and Mirza, 2010). It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new lead anode alloys and production processes for lead anodes to be used in copper electrowinning, the industry still has some unresolved issues. These relate to the necessity of having higher mechanical properties especially for the lead anodes in liberator cells in copper electrorefining and for cobalt and nickel electrowinning as these tankhouses operate at temperatures of 65-75 oC compared to 40-45 oC in case of copper electrowinning."

Jan 1, 2016

By D. Pérez Escobar

Multiphase steels are quite sensitive to hydrogen embrittlement. Laboratory tests to evaluate this often use electrochemical, charging to introduce hydrogen into the sample, but damage purely caused by hydrogen charging has to be avoided. A ferrite-bainite steel, was charged using various conditions to identify when surface blisters occurred. Samples were also checked for internal, damage by electron microscopy. This study was repeated for three other multiphase steels and pure iron. An HSLA steel, was found to be more resistant whereas pure iron was quite susceptible to internal, hydrogen damage. For al, industrial, steels, cracks concentrated in the middle of the sample were attributed to inclusions and segregations, inherent to production.

Jan 1, 2010

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

By Y. M. Jubeli

"Abstract - Gamma-ray spectrometry, an effective tool in geological mapping, was used to define boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains. This paper describes the role of an airborne gamma spectrometric survey which was orginally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to significant modifications and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack sufficient geological data."

Jan 1, 1997

By Grant Small, Jessica Kinal, Christopher J. Greet

"The conversion from an electrochemically reactive grinding media (forged steel) to a more electrochemically inert alloy (high chrome white iron) not only reduces the wear rate of the grinding media, but also has an impact on the grinding chemistry. Typically the grinding chemistry becomes more oxidising, with less reducing Eh values and more dissolved oxygen in the pulp. There is also a decrease in the EDTA extractable iron, which is an indication of the change in the media corrosion. These changes are indicative of alterations in the surface chemistry of the minerals that the operator is trying to separate. For porphyry copper ores the changes in the pulp and surface chemistry not only affect the copper sulphide minerals, but also impact the iron sulphides (i.e. pyrite and pyrrhotite). Generally, with more oxidising pulp chemical conditions during grinding there is an increase in the oxidation of the iron sulphides which renders their surfaces hydrophilic, thereby depressing flotation. This leads to improved selectivity for copper sulphides against iron sulphides.INTRODUCTIONPorphyry copper deposits are the dominant source of copper that is mined today to satisfy global demand. These style of deposits typically contain one percent copper mostly as chalcopyrite, but may contain other copper bearing minerals (for example, bornite, chalcocite, azurite, malachite), small quantities of pyrite and quartz. Porphyry copper deposits also contain economically significant quantities of gold, silver and molybdenum. Interestingly, the majority of the world’s porphyry copper deposits are concentrated along tectonic plate boundaries (Figure 1)."

Jan 1, 2016

By J. J. Denny

The purpose of this paper is to present, briefly, an outline of Canadian practice in the milling of gold-bearing ores- not, however, including those auriferous ores which are mined and milled primarily for their content of some other metal. It is not the writer&apos;s intention to offer technical data, nor to discuss any particular phase of the metallurgy, but rather to give a general résumé of past and present methods. As it is only within recent years that gold milling has assumed prominence in Canada, much of the technology is modern, and detailed articles describing the practice adopted in the several mining districts, and recording the various changes and innovations that have been made from time to time, are to be found in the Transactions of the Canadian Institute of Mining and Metallurgy, and in the mining journals. Prior to the year 1860, any gold that had been produced in Canada had come from placer operations in British Columbia, but &apos; during that year lode gold was discovered in Nova Scotia, in quartz veins, and in several localities mines were opened and small mills of very simple character were erected to treat the ore. These plants, equipped with stamps, or arrastre, were only effective in recovering the free gold. Concentration and chlorination were introduced in an endeavour to save the gold occurring in intimate association with metallic minerals, but, due to various circumstances, gold mining and milling did not progress in Nova Scotia.

Jan 1, 1930

By Bernhard Schwab

A popular rule in the mining industry is that a property should only be developed if average unit production cost is less than a given proportion of the estimated long-run price of the mineral. This paper provides a comparative analysis of the average cost approach (ACA) with the use of net present value (NPV) as an investment criterion. It is concluded that the ACA is an easily understood and easily applied rule of thumb which may serve as a rough first screening device, for example in the early stages of deposit exploration. Its operational convenience is at the expense of accuracy and validity, and the NPV provides a sounder method of making decisions, especially in the case of marginal deposits.

Jan 1, 1978

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016