Search Documents

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By M. Carvalho

The primary motivation underlying the proposal of polygeneration systems for mine sites is to increase the efficient use of natural resources by combining different technologies and energy resources while satisfying energy service demands. For many mineral producers, particularly in Canada?s mining extremes of climate and depth, energy in support of mineral production can be the second largest cost centre after labour. A generic methodology is proposed for the design of energy supply systems in mine sites, based on a search for the minimum discounted cost of energy supplied for all feasible different plant configurations. These configurations can be represented within a connectivity matrix which corresponds to a network representation. A Mixed Integer Programming formulation is set out for the multiperiod synthesis and operational planning problem. This is characterized by i) binary variables for the selection of technologies, ii) integer variables for the determination of the number of units installed, and iii) by continuous variables for the representation of energy and economic flows. Through the integration of particular energy supply strategies matching specific mine circumstances (on-grid, remote, degree days, etc) and consideration of technologies that improve energy efficiency, hitherto not considered new technologies and demand management systems or new perspectives on optimal mine site energy supply can be investigated. Some of these investigations identify the economic conditions through which biomass energy feedstocks should be used, for direct heat production, for gasification and providing for Fischer-Tropsch syndiesel manufacture. As well as integrating demand from mobile diesel-fuelled plant into an optimization procedure that hitherto has only been considered for static energy production and consumption plant, this analysis shows how the techniques can be used to explore economic conditions of threshold prices for biomass (purpose-grown biomass and peat are considered herein) and trucked-in diesel. The methodology also allows for electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply.

Aug 1, 2013

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By R. D. Parker

Location The Frood ore-body is expressed on surface as a prominent gossan ridge, with a total length of approximately two miles. The original Frood (the old No. 3 mine of the Canadian Copper Company) is at the southwest end of this gossan; adjoining it on the northeast is the Frood Extension (until 1929 the property of i:he Mond Nickel Company), while at the extreme northeast end is the Stobie mine. The first two of these divisions of the ridge form the Frood mine as it is known today.? This lies in lots 6 and 7 of the sixth concession, township of McKim, and is two and a half miles north of the city of Sudbury. The general elevation is 1,000 feet above sea level. The Ore-Body The Frood-Stobie parallel offset(l), as its name implies, has no connection in the field with the main mass of the Sudbury nickel eruptive-a norite. It lies one mile to the southeast of that body, and, in general, parallels it in strike. The ore occurs as a more or less tabular structure in what is known locally as the Sudbury series. They are the oldest rocks of the district, and have been placed by Collins(2) as earlier than the lower Huronian, of pre-Cambrian time. The series is comprised of sediments, volcanics (both acid and basic flows), tuffs, agglomerates, breccias, and basic intrusives, all highly metamorphosed, yet all forming a more or less regular picture. The controlling feature of the area has been the attitude of the sedimentary strata, from which has arisen the present sill-like character of the flow rocks, the basic intrusives, and the ore-body itself.

Jan 1, 1932

By Charles B. Newmarch

Abstract In the course of coal studies undertaken by the B.C. Department of Mines in southeastern British Columbia, special attention was directed to problems of coal seam correlation. Methods that had been used successfully in other coalfields were found, in the Crowsnest area, to have a restricted use or furnished only additional evidence that might prove helpful when used in conjunction with other criteria. A correlation technique involving semi-quantitative spectrographic analyses of coal ashes was developed. Elements detected in the ash include Si, B, P, Fe, Mg, Mn, Pb, Ti, Cr, Ga, Ca, Al, Ge, Ba, Mo, V, Ag, ?y;b, Na, Zn, Zr, Ni, Sr, Cu, K. Of these, the elements found to be most useful in correlation were Na, Ba, Si, V, and Mg. The element Na was invariably detected in the ash from one of the seams but was not found in samples taken from any of the others. In all of the four seams sampled statistically, significant differences in the amount of certain trace elements were noted. When the values obtained for these trace elements were portrayed in the form of histograms, the resulting diagrams had a characteristic shape for each seam. The diagrams provided a basis for seam identification within the limited area (8,000 feet by 4,000 feet) that was investigated. Introduction During the field seasons of 1946, 1947, and 1948 the British Columbia Department of Mines undertook a geological investigation of the coal measures of southeastern B.C. As field work progressed in the Crowsnest area it was found that, within the Kootenay formation, which contains all the commercial seams of the region, the coal beds are the most persistent stratigraphic units. Because of relatively rapid changes in ?both the thickness of the seams and the interval between seams, difficulty has invariably been experienced in attempts at correlation. Even short-range correlati0ns by able geologists who have worked in the Crowsnest coal basin have been questioned by the operating companies. It was apparent, therefore, that a more dependable correlation technique was needed so that stratigraphic and structural studies could be of greatest value. This paper presents, firstly, a summary of the results obtained in attempted correlations using methods that have been found effective in other coalfields. Secondly, a method based on semi-quantitative spectrographic analysis of coal ash is described and the apparently promising results are discussed.

Jan 1, 1950

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By G. Barr

"The Polymetallic Twin Metals Project deposits in Northern Minnesota are being developed by Twin Metals Minnesota. Amongst the flowsheet alternatives being examined at a prefeasibility study level is one involving flotation of a bulk concentrate followed by high temperature autoclaving of the concentrate using the PlatsolTM Process to solubilize all the valuable metals in the concentrate (Cu, Ni, Pt, Pd and Au). Autoclave operating conditions have been established in which recoveries of all the pay metals are in the 92 to 99% range, and the autoclave residence time has been reduced to an hour. The stability of the precious metals in solution after autoclaving has been assessed, as well as the impact of internally recycling process liquors to the feed to the autoclave.INTRODUCTIONPlatinum group metals (PGMs; platinum, palladium, rhodium, ruthenium, iridium and osmium) are traditionally recovered from their ores by production of a high-grade concentrate by flotation and/or gravity concentration followed by smelting of the concentrate. Concentrates are smelted to remove nonsulphide minerals and converted to remove iron and sulphur. The resulting high PGM grade matte is processed hydrometallurgically to leach the base metals, leaving a residue with a very high grade (20-40%) PGM concentrate for final refining to individual PGMs. Due to the complexity of this process and its high capital cost, this process can only be applied economically to high grade PGM ores. Lower grade PGM concentrates might be accepted as copper and nickel concentrates but may not yield attractive payment terms for the PGMs. The mineralized Duluth Gabbro region of Minnesota hosts several low grade base and PGM deposits and Twin Metals Minnesota is working to develop the Twin Metals Project deposits. Earlier studies at both pre-feasibility and feasibility level, by other mining companies, have failed to yield an economically viable project based on the traditional process. It is possible to produce a saleable copper concentrate from these ores, but economic recovery of nickel and PGMs into saleable concentrates proved elusive.In the late 1990’s and early 2000’s the Platsol™ process was developed at SGS in Lakefield, Ontario (at the time Lakefield Research Limited) for the NorthMet deposit (also within the Duluth Gabbro) owned by PolyMet Mining. The process developed was a high temperature chloride-assisted pressure oxidation process capable of dissolving simultaneously the base metals (Cu, Ni, Co, Zn), gold and the PGMs."

Jan 1, 2012

By W. J. Dick

THE purpose of this paper is to point out, briefly, the importance of the coal mining industry of Alberta and to stress the economic factors that hinder its development; also to offer suggestions relating to the major problems of the industry. The minor problems will not be dealt with in detail, because, if the major problems are taken care of, it is felt that the industry itself can take care of ,he remainder. COAL MINING NO LESS IMPORTANT THAN GOLO MINING The large increase in metal mining development in all provinces of Canada, excepting Saskatchewan, Alberta, and the Maritimes, has had the effect of focussing public attention on this branch of the industry. The fact, also, that this development came at a time of depression has been of immense benefit to Canada as a whole. On account of the necessity and consequent demand for gold, with its attendant increase in price, through government action, from $20.67 per ounce to $35.00 per ounce, it is safe to say that the public of Canada have become, today, gold mining conscious. While everyone admits the great value. of the gold mrn111g industry, nevertheless, the equal value to Canada of certain other industries must not be lost sight of. The coal mining industry, in particular, is worthy of greater public and government support than has been accorded it in the past. It would seem unnecessary to stress this matter to a meeting of the Canadian Institute of Mining and Metallurgy, but unless certain facts are brought to your attention, there is danger that the coal mining industry will not be developed to the extent its national importance deserves. Too many public men and men in authority are unaware of the value of coal mining.

Jan 1, 1936

By John McEwen, Ian R. Jonasson, David H. Watkinson

"Mine Gallen is a zinc-rich pyritic volcanogenic massive sulphide deposit that occurs in a fault-bounded block of intermediate volcanic rocks. The block is completely surrounded at the present erosion level by the eastern part of the Lac Dufault granodiorite. The volcanic succession includes a massive feldspar porphyry that is probably a subvolcanic intrusion, an andesitic flow unit and lapilli tuffs. The latter are variably sericitized and pyritic, especially in the vicinity of the massive sulphide into which they grade.The ore body is predominantly pyritewith local sphalerite contents as high as 20%; minor chalcopyrite and trace galena are disseminated, but are found mainly along late cleavage. Most ore is a breccia of massive to banded pyrite-sphalerite, veined by massive and complexly banded sulphides. These structures formed by repeated blocky jointing, cracking, sealing, healing and annealing as hydrothermal fluid repeatedly passed through a developing sulphide mound. The deposit is interpreted to have grown on the seafloor in a manner similar to active mounds in the Galapagos rift.RESUME La Mine Gallen exploite un gisement de sulfures massifs volcan géniques comprenant essentiellement de la pyrite riche en zinc. Ce gisement se trouve a /'intérieur d’un bloc de roches volcaniques de caractère dacitique a andésitique, limite par failles et entoure de tout cote par la granodiorite du Lac Dufault. La séquence volcanique comprend des coulées andésitiques et des tufs à lapilli ainsi qu'un porphyre feldspathique massif sub-volcanique. Les tufs sont sericitises et pyritises, tout particulièrement au voisinage des sulfures massifs."

Jan 1, 1990

By D. A. Karvonen

In 1970, the Government of Saskatchewan instituted a program aimed at resolving the dilemma of excess productive capacity over the market demand which existed for potash produced in Saskatchewan. The two primary elements of the program were prorationing of potash production to market demand and a minimum selling price. The paper reviews the factors, both local and international in nature that led to the introduction of the program. The licensing mechanics and the operation of the program, along with the changes that have been introduced in two and one-half years of operation, are discussed. Attention is given to the results of the controls as they affect the industry and the province. Also discussed is the outlook for Saskatchewan potash in world markets.

Jan 1, 1973

By G. E. Norman, A. L. Mckague

"The new smelting process commenced operation in 1978. The pelletizing and sinter plants were replaced with slurry-fed roasters and the blast furnaces with electric furnaces. The existing converter aisle and matte handling facilities remained unchanged.Process DescriptionNickel-copper concentrate is partially roasted in two slurry-fed fluid bed roasters. After gas cleaning, the sulphur dioxide gas is transferred to the acid plant. The roaster product is conveyed to two electric furnaces for smelting to produce a waste slag and furnace matte. The slag goes to the disposal area and furnace matte containing the metal values is processed in the converters for further removal of iron and sulphur.The final matte containing about 75 per cent metal values is shipped to the refinery in Norway.The commercial smelter was designed for 2135 tonnes per day of concentrate, with an availability of 85% . Roasters and electric furnaces were sized at 117 per cent of design, or 1250 tonnes per day on each of two lines. Concentrate storage capacity in the plant is sufficient for two to three days' plant operation.The new smelting process will be discussed under the following headings:Concentrate Slurry HandlingFeed PreparationRoaster OperationRoaster Gas CleaningCalcine TransferElectric Furnace Operation and Process Control Converting and Matte HandlingUnder these headings, process control , equipment changes, and plant performance after three years' operation is reviewed. A brief discussion of accident prevention , and working environment is also included ."

Jan 1, 1984

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By James W. Cameron

DESPITE the fact that, after oxygen and silicon, aluminum is the most abundant and widely distributed element in the earth's crust, it is, commercially, a modern metal. Attempts were made by Sir Humphrey Davy and other chemists to decompose alumina, the oxide, into its elements, but with unsatisfactory results, and it was not until 1827 that Wohler succeeded for the first time in isolating the metal in pure form. Some thirty years later, commercial production of aluminum was started in a plant near Alais, France, using a process developed by Deville which was a modification of that of Wohler. It was not, however, until around 1886 that possibilities of low-cost production were realized. Hall and Heroult discovered, independently, the now famous process for extraction of aluminum by the electrolysis of alumina (Al,O,) dissolved in fused cryolite. This discovery, with its subsequent effect in reducing the price of the metal, was perhaps the greatest single factor contributing to the remarkable growth of the aluminum industry. But only in the years following the Great War did aluminum begin to attain equal importance in many fields with other non-ferrous metals. Numerous factors, political and economic, in the past decade have had a profound effect on the industrial history of the metal. At present, systematic substitution of aluminum for other base-metals is proceeding at a rapid rate in such countries as Germany and Italy with a view towards 'economic self-sufficiency'. Quite naturally, ?the economic depression started extensive research and experiment in various industries in an attempt to improve efficiencies and lower costs. Partial answers have been found in the extended use of aluminum and its alloys. Even against the background of tremendous technological advance that has marked the past fifty years, the rise of the aluminum industry must necessarily stand out conspicuously.

Jan 1, 1939

By Piotr Litwa

The paper focuses on actions aiming at improvement of work safety in mines, particularly in those extracting hard coal, taking into account the characteristics of natural hazards in Polish underground mining and the reasons of mining disasters connected with those hazards. It refers to conclusions addressed to scientific and research centres, drawn during last decade by Commissions appointed by the President of the State Mining Authority in order to investigate reasons and circumstances of incidents, which till now, could not have been accomplished because of financial reasons. Furthermore, the paper presents basic assumptions of the Strategic Research Project Improvement of work safety in mines, announced by the National Centre for Research and Development at State Mining Authority?s President request.

Aug 1, 2013

By Sebastian Siebert

Unmanned Aerial Vehicles (UAV) as a data acquisition platform and as a measurement instrument have become attractive for many surveying applications in civil engineering. However, their performance is not well understood for these particular applications. The specific scope of the presented work is the performance evaluation of a UAV system that was built to rapidly acquire mobile 3D mapping data for large earthmoving construction sites. Details to the components of the developed system (hardware and control software) are explained. A novel program for photogrammetric flight planning and its execution for the generation of 3D point clouds from digital mobile images is explained. A performance model for estimating the position error was developed and tested in several realistic construction environments. Results to these tests are presented as they relate in particular to large excavation and earth moving construction sites. Results and experiences with the developed UAV system are in particular useful for researchers or practitioners in need for successfully adapting UAV technology for their application(s).

Aug 1, 2013

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015

By D. D. Bell

This paper presents the history of uranium procurement and demand, and takes a look at future requirements. The three basic conclusions drawn are: (1) the productive capacity of former and existing producers whose operations may be profitably reactivated is insufficient to meet demand projected beyond 1975; (2) reserves in the $5 -$10 price range do not provide the flexibility to sustain production at the high rates required in the late 1970's; and (3) only higher prices can overcome these deficiencies, as this would provide sufficient inducement for the industry to explore for and develop new reserves and productive capacity.

Jan 1, 1967

By D. -A Tremblay

Dynamic wetting spread factors and interfacial heat transfer coefficients were determined for aluminum droplets solidifying on copper substrates, The spread factors were determined from the droplet geometries while the heat transfer coefficients were obtained by solving inverse heat conduction problems, 1-D and 2-D heat transfer models are presented and the results they provided are compared, For the latter, a sensitivity analysis was also performed to determine the influence of thermophysical properties and boundary conditions. Experiments were alternatively carried out with three different gaseous atmospheres and the dynamic wetting spread factors were correlated to the interfacial heat transfer coefficients.

Jan 1, 2005

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004