Search Documents

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

By W. E. Oching, M. M. Ghomshei

Attracting and retaining workers in mining industry has become an uphill battle to many mining companies. As workers with significant experience retire, it is getting more difficult to attract not only new workers but also top talent to the mining industry to replace professionals exiting the workforce. To make matters worse, students’ enrolment in the post-secondary mining programs in Canada and USA is continuously declining year after year for reasons not directly linked to job market. This raises a question of how can the future needs of mining be met? This paper focuses on avenues for collaboration of industry and educational institutions to meet the current and future needs of mining. It provides effective approaches that mining institutes can engage with program advisory committees, role of the mining industry in supporting both faculty and students, how to harness the benefits of diverse workforce in the country and use of innovative technologies to attract young workers in mining. This work presents Human Resources (HR) professionals with tools that they can use to hire and retain skilled workers with strong interest to work in the mining industry. It also provides HR professionals with an opportunity to re-evaluate their restructuring practices during economic downturns as they reduce number of employees on temporary or permanent basis. The paper stresses the need of working together of the mining stakeholders including mining industry, academic institutions, First Nations’ communities and provincial(state) and federal governments to meet the current and future demands of mining as the industry experiences shortage of labour and low students’ enrolment in post-secondary mining programs. It is shown that mining educational institutes can enhance their programs and recruitments through establishing a better communication with all stakeholders. This communication can be facilitated by creating a national advisory board, to work with all mining programs at the national level for sustainable mining.

Jan 1, 2023

By D. Song

In this paper, the differential equations governing the mass transport and the electrochemical reaction in a cathode catalyst layer of polymer electrolyte membrane fuel cells are solved based on the polynomial series expansion method. Explicit expressions for the polarization curve as well as for the distributions of oxygen, current density and overpotential are obtained when a quadratic, cubic or quartic polynomial is employed to approximate the oxygen concentration distribution. These kinds of explicit solutions are desirable for MEA design and diagnosis purposes. The comparison between the conventional numerical approach and the explicit solution approach proposed here shows that satisfactory accuracy can be reached by the first four terms of the polynomial series. The effect of the catalyst layer thickness on the accuracy of the obtained explicit polynomial solutions is also discussed.

Jan 1, 2005

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017

By Fathi Habashi

"On August 3, 1888, German Patent No. 43977 entitled ""A Process for the Production of Aluminum Hydroxide"" was issued*. The discovery which led to the patent was made by the Austrian chemist Karl Josef Bayer (1847-1904) (Fig. 1) who was at that time in Russia, and the process became known as the Bayer Process in his honour(1)(2)- The process imediately achieved industrial success, displacing the pyrometallurgical process that had been used until that time to produce alumina. The Bayer Process involved the pressure leaching of bauxite with NaOH solution to obtain sodium aluminate solution from which aluminum hydroxide was precipitated by seeding. Today bauxite is not only the principal source of aluminum but also of gallium, both metals being effectively recovered by the Bayer Process. The purpose of this paper is to outline the historical background of this discovery and its importance to hydrometallurgy."

Jan 1, 1999

By Les Philips

National Institute for Safety and Health?s (NIOSH, USA) Office of Mine Safety and Mine Safety and Health (OMSHR) has definitions for: -Proximity Detection as detection of personnel, vehicles and other objects near a machine using some type of sensor technology -Proximity Warning (aka Collision Warning) as detection of personnel, vehicles and other objects near a machine resulting in alarms that ?Warn the operator only ?Warn the operator and nearby personnel (two-way) -Collision Avoidance as the processing of sensor information resulting in control signals or actions that alter machine status/movement to avoid a collision by ?Computer control ?Human control

May 1, 2013

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By A. L. Mular

This paper provides a worthwhile contribution to the knowledge needed for calculating and using mathematical models of grinding circuits. The computer search algorithm proposed should remove much of the guesswork as well as reduce computer processing costs and improve the accuracy of estimated parameter values for grinding mill models.

Jan 1, 1970

By D. C. R. Espinosa, P. Aliprandini, F. P. C. Silvas, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel ores are divided into two types: sulfide deposits and lateritic deposits. About 60% of nickel resources are found in laterite ore, while the remaining 40% is contained in sulfide ore. Laterite ore is usually processed via pyrometallurgical means or through hydrometallurgical techniques that include acid leaching and metal value recovery from solution. In this study, copper and nickel adsorption by Dowex M4195 ion exchange resin from an acidic sulfate liquor was investigated. The acidic sulfate liquor was collected from an atmospheric leaching process (AL) of laterite ore. Ion exchange experiments were conducted in a batch system by varying parameters such as pH, time, metal concentration and temperature. Initially, mono-elemental synthetic solutions of nickel and copper were used in the experiments and then a synthetic solution simulating AL liquor was tested. Test results showed that the resin exhibited high selectivity towards copper and nickel, however, a high concentration of iron in the synthetic AL solution interfered with the recovery of nickel and cobalt by the resin.INTRODUCTION Nickel is one of the most important industrial metals in the world. It is widely used in industrial applications, such as the production of stainless steel, magnets, electroplating and special alloys (Dizge et al., 2009). The main sources of industrial nickel production are sulphide deposits; only 40% of industrial production uses lateritic ores. However, it is estimated that 60% of global nickel resources are found in nickel laterite deposits (Kuck, 2016). Since industrial nickel demand continues to grow, the development of new technologies for the extraction of nickel from laterite ores has become an interesting research topic (Agatzini-Leonardou, 2009)."

Jan 1, 2017

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By Peter Hayes, Evgueni Jak, Taufiq Hidayat, Gary O’Connell, Denis Shishin, Jeff Chen, Francis Letarte

"Knowledge of slag properties is required for the optimisation of smelting operations. The phase equilibria and viscosities of the Al2O3-CaO-FeO-Fe2O3-MgO-MnO-NiO-Cr2O3-SiO2 slags at conditions of interest to Koniambo Ni-laterite smelting operations have been investigated. High-temperature re-equilibration phase equilibrium experiments of industrial slags followed by rapid quenching and direct measurement of phase compositions using electron probe X-ray microanalysis (EPMA) have been undertaken in the olivine and pyroxene primary phase fields at temperatures between 1475 and 1600°C and SiO2/MgO weight ratios between 1.57 and 2.09. Phase equilibria predictions were performed using FactSage thermodynamic software. A slag viscosity model available in the FactSage thermodynamic package has been used to calculate the viscosities of the liquid slags. The Einstein-Roscoe equation combined with the predicted phase equilibria data have been used to estimate the viscosities of the slag slurries (slag + solids). The information provided can be used to assist in the evaluation of the furnace performance, to assess further optimisation of slag composition and to explore possibilities of targeted feed changes.INTRODUCTION One of the key steps in the production of ferronickel from nickel laterite ore at Koniambo Nickel SAS involves reduction and smelting of pre-dried nickel-bearing saprolitic ore (high Mg and Si) in an electric furnace at temperatures up to 1650°C. The characterisation of the slag properties as functions of key operational parameters, such as, temperature and composition, including liquidus, the proportions of solids and viscosity, is essential for improving control and optimisation of the operations. The slag produced in the smelting process is a complex oxide system with the major chemical components including Al2O3, CaO, Cr2O3, “FeO”, MgO, “MnO”, “NiO” and SiO2. Characterisation of these multi-component systems using a solely experimental approach becomes increasingly complex as the number of components is increased."

Jan 1, 2017

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By Gurupraveen Ramanathan

Slot raises are relief holes within a stope in longhole stoping methods, designed to provide a free face that facilitates the expansion of the blasted rock during blasting, ultimately achieving the desired fragmentation. Various methods are employed to produce these slot raises, like conventional drop raise drilling, raisebore & V30 drilling. However, slot drilling is generally characterized by high costs and limitations in precision, resulting in unplanned ore losses and dilution. This paper introduces a novel alternative to slot drilling referred to as the "paste slot", designed specifically for paste backfill operations in underground mining. This new method emphasizes considerations in cured paste strength, paste wall removal, and stope dimensions and employs modified drop raises or dumped rings to optimize blast gas effectiveness and material flow. The paste slot method eliminates the need for reamers and reduces the total slot drill meters an average from 650m to only 300m for narrow stopes (3-4m wide). This significantly reduces the stope cycle time, leading to substantial cost savings and increased productivity. This new method was successfully implemented at the underground mines in Canada and Australia, resulting in a 20% reduction in stope cycle time and cost savings of 53,000 USD per slot compared to the conventional slot. This paper discusses the design and execution strategy of the paste slot method in underground paste backfill operations. It highlights the advantages of the method, shares operational insights gained during implementation, and showcases its potential applicability to other mines across Canada and globally.

Oct 1, 2024

By L. L. Bolton

The Department of Mines as at present constituted has evolved from the organization which came into existence following the passage of the Geology and Mines Act by the Dominion Parliament in 1907. At the outset, it may be said that it is not a function of the Department of Mines, nor of any of its branches, to administer the mining rights vested in the Crown. The title to Crown lands in the provinces of Nova Scotia, Prince Edward Island, New Brunswick, Quebec, Ontario, and British Columbia ( with the exception of certain specified areas, such as Indian Reserves, Ordnance Lands, the Railway Belt of British Columbia, and the Peace River Black) is vested in the respective provincial governments ; the title to Crown Lands in the provinces of Manitoba, Saskatchewan, and Alberta, the Yukon and Northwest Territories, and in the Canadian Arctic, is vested in the Dominion Government, and matters pertaining thereto are (with a few exceptions) administered by the Department of the Interior, Ottawa. Nor are statistics of mineral production at present collected and published by the Department of Mines. This function did belong to the Geological Survey from 1886 to 1906, and to the Mines Branch from 1907 to 1920; but commencing with 192l this duty was transferred to the Dominion Bureau of Statistics, consequent upon the decision of Government to place the collection of all statistics under the direction of one officer.

Jan 1, 1929

By H. R. McCabe

"The study of a detailed series of structure and isopach maps of the Palaeozoic strata of southwestern Manitoba indicates that the principal Palaeozoic tectonic elements -the Williston Basin and Elk Point Basin -have been modified to a considerable extent by major tectonic features of the Precambrian basement. The principal basement feature is the break between the Churchill and Superior provinces, which coincides roughly with the Manitoba-Saskatchewan border. East-west-trending orogenic belts within the Superior crustal block may also be reflected to some extent in later Palaeozoic movements. In addition, the Superior crustal block, as a whole, appears to have had a slightly different response to the tectonic forces, giving rise to both basin subsidence and basin uplift. During periods of deposition, especially during Ordovician time, the Manitoba portion of the basin appears to have undergone a relatively higher rate of subsidence, whereas during periods of erosion relatively greater amounts of uplift and truncation have occurred. As a result, the depositional and erosional patterns for most of the Palaeozoic formations in southwestern Manitoba are somewhat anomalous relative to the regional basin framework.Some prominent Palaeozoic structures probably are the result of salt solution and differential compaction caused directly or indirectly by relatively minor tectonic movements related to Precambrian basement features. In particular, the prominent hinge line at the edge of the Devonian Prairie Evaporite salt basin may be due, in large part, to salt solution. Numerous other small structural lows, structural highs and isopach thicks, probably resulting from salt solution, occur along the salt edge and have been important in modifying and controlling Mississippian oil accumulation in the Daly-Virden producing area."

Jan 1, 1967

By D. W. R. George, J. L. Stewart

Developments in the last decade, which have contributed to increased productivity and decreased coke rates in the iron blast furnace, are reviewed. Future progress in blast-furnace practice is also considered.

Jan 1, 1966

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015