Search Documents

By R. L. Dunsmore

Introduction If one had been called upon to describe petroleum oil refining seventy-five years ago, he could have acceded to the request quite satisfactorily in about fifteen minutes. Fifteen years ago, an hour and a half would have been sufficient to give a general idea of oil refining, and of the equipment used for this purpose. Today, so extensive has been the research into all phases of the refining and manufacturing of petroleum products, and so rapid the strides in improvement in technique and equipment, that I doubt if a week would suffice to give an adequate outline of ail the ramifications of present-day oil refining. I propose to only 'hit the high spots', dealing particularly with the equipment and methods employed at the Imperoyal refinery, which you are to visit. Crude oil, the refiner's raw material, contains essentially only two elements, hydrogen and carbon. These are not present in the free state but are combined in various proportions as 'hydrocarbons'. A given crude oil is not made up of just one hydrocarbon, but of myriads; some solid, others liquid, and still others gaseous at atmospheric temperature and pressure, ail dissolved one in the other. Moreover, the nature and the relative amounts of the several hydrocarbons vary very considerably in crude oils from different sources. That is, a 'crude' from Oklahoma will contain hydrocarbons not present in crude from Mexico, and is different again from the Venezuela crude. Not only this but oil in a certain well in, say, Peru may be differently constituted from that in a well half a mile distant from it.

Jan 1, 1931

By R. H. Chambers, L. Alderman

"The paper is introduced by an examination of the factors which have led to the present world-wide interest in charging preheated coal to coke ovens. Various possible methods of preheating and charging the coal are considered and reasons are given for the adoption of the methods chosen. The design of the pilot preheating plant for the British Coke Research Association is discussed and its influence on the design of the commercial units for the South African Iron and Steel Corporation's plant at Pretoria and the British Steel Corporation's plant at Beighton are explained. Operating procedures on the pilot plant are described, particularly with regard to the charging of the preheated coal. Design features of the commercial installations, engineered by Simon-Carves Ltd., are explained with emphasis on the built-in safety of the control system of the preheating plant, and the particular problems associated with the erection of such plants on working coke oven batteries. Commissioning and operating procedures are described and the problems associated with the integration of the preheating plant into the normal pushing schedule of the plant are discussed. Preliminary operating results with regard to the effect of preheating on coal throughput on the commercial plants and on the properties of the coke produced are given."

Jan 1, 1972

By A. E. Boudreau

Abstract-It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydrothermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward- migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By A. E. Boudreau

It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydro thermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward-migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By K. Thuro, H. Käsling, C. Wieser, G. Nuijten

"The time-dependent behavior of brittle rocks during stress relaxation is of great interest for mining industry, nuclear waste disposal as well as tunneling and underground construction. Several studies have shown that both elastic as well as inelastic deformation occur during stress relaxation (Emery, 1964; Zang & Berckhemer, 1989). While elastic strain occurs already during the drilling process, inelastic deformation is time-dependent and can endure for hours, days or weeks. To investigate the evolution of microcracks during core relaxation, two crystalline core samples were recovered from high in situ stress conditions in Europe’s deepest mine in Pyhäsalmi (Finland). Samples were prepared for testing within one hour after coring such that a large portion of the time-dependent component of relaxation could be recorded over several days using ultrasonic velocity as well as acoustic emission (AE) measurements.Results from AE analysis show an exponential decrease in the number of events over a period of several hours. Repeated sudden increases of acoustic events can be related to the propagation or the interaction of cracks. In the first hours of recording also the signal energies reached the highest values and the increases in signal energy correlate well with increased event rates. On additional drill cores, P-wave velocities were measured parallel and in 45° distances perpendicular to the core axis. After core recovery, stress-induced microcracking caused an exponential decrease in wave velocities similar to AE rates. Lowest compressional wave velocities were measured parallel to the core axis and thus normal to the foliation and in the direction of the maximum in situ stress component. The highest measured velocities occurred parallel to the foliation plane. Within the samples, the anisotropy ratios were up to 1.37 at the beginning of the measurements and increased to values of up to 1.8 after 45 days. The wave velocity anisotropy is in agreement with the in situ stress orientations."

Jan 1, 2015

By Henri-Loui Jacob, Suzie Nantel

"Depuis la fin des annees 1800, la province de Grenville represente pour Ie Quebec une source importante et diversifiée de minéraux industriels. Le Ministère de l'Énergie et des Ressources du Québec, dans Ie cadre de I'entente auxiliaire Canada-Québec, et les compagnies minieres y ant multiplié, surtout depuis 1983, leurs travaux d 'exploration, de cartographie, et d'évaluation pour les minéraux industriels. Ces travaux ant conduit ala découverte et ala mise en valeur de gisements de granite architectural, de graphite, de dolomite et ant aussi permis de repertorier des gîtes et des indices prometteurs de wollastonite, de silice, de calcite. de dolomite, de silicates d'alumine et de terres rares. Les gisements récemment découverts sont actuellement exploités au sur Ie point de l'être et les gîtes et les indices les plus prometteurs ant été jalonnés.ABSTRACTSince the late 18oos, the Grenville Province in Québec has been an important and diversified source of industrial minerals. The Ministere de l'Énergie et des Ressources du Québec, under the Canada-Quebec Mineral Development Agreement, and the private sector have put an emphasis on exploration, mapping and evaluation programs in the Grenville Province for minerals, particularly since 1983. These programs have led to the discovery and the development of deposits such as architectural granite, graphite and dolomite, and have also led to inventories of occurrences and prospects of wollastonite, silica, calcite, dolomite, alumina silicates and rare earths. The deposits discovered lately are presently being quarried or will be in the near future. The most promising occurrences and prospects have been claimed."

Jan 1, 1990

By W. J. Mcgaughey, M. A. Vallée

"Abstract -The application of geophysical technology to resource delineation aims to improve the quality of resource/reserve estimates by integrating high-resolution survey methods, geophysical modeling and inversion with three-dimensional representations of geological and mineral deposit data. The use of geophysics can cost-effectively improve a geological interpretation based only on geological and sampling data. Success depends upon the ability to use geological visualization and modeling software, first to develop a three-dimensional geological model and then to modify it interactively by integrating geophysical data with the geological and sampling data.The high resolution required for mineral delineation geophysics results in a focus on borehole seismic and high-frequency electromagnetic methods. Borehole wireline logging is used to develop an understanding of the relationship between physical properties and geological description. Data from core samples and borehole wireline logs allow the construction of a three-dimensional physical property distribution, consistent with the existing geological interpretation. The three-dimensional physical property distribution is used for both geophysical forward modeling (to compare to field data) and as a starting model in iterative inversions.Advanced visualization techniques allow the simultaneous viewing of the three-dimensional physical property model, the geological information and data from which it is derived, and the geological interpretation and the geophysical results. Geophysical results may be simulated responses from a forward model or the output from a numerical inversion in the form of an updated physical property distribution. Iterative refinement of the geological interpretation is required to ensure consistency with the geological and geophysical data. The key to success with this approach is that all relevant geological, geophysical, and rock property data reside in a common, visual model of the earth.Examples from massive sulfide deposits illustrate the benefits obtained by the integration of geophysical and geological data."

Jan 1, 1998

By R. E. Stewart

"Using the concept of economic life and marginal analysis, it can be shown that proper equipment replacement timing can save a mining company many thousands of dollars. To assist management with determining the economic life of mining equipment, a new computer package has been developed. The package, called ERG (equipment replacement guide), incorporates all important economic factors related to equipment usage, such as operating costs, maintenance costs, salvage values, depreciation, volume of work, tax credits, inflation rates, ROJ, etc. The information is used in a series of equations which balance the costs of new equipment against the total cost of old equipment. The solution of the equations determines economic life and the point in time when the old equipment should be replaced. IntroductionIn an operating mine, equipment must eventually be replaced or downgraded for a variety of reasons. Fleets of haul trucks, dozers and other major pieces of equipment deteriorate over time until the mounting costs of maintenance and repair force either a major overhaul or the ir replacement by new and more efficient pieces of equipment.The question of determining the best time to replace old equipment has been approached in many different ways. Various methods, ranging from operating experience, intuition and physical necessity to sophisticated computer models have been devised to help cope with equipment replacement decisions . The best of the se will incorporate the most important economic factors related to equipment usage, such as operating and maintenance costs, salvage values, depreciation, work delivered, the cost of capital, tax credits and, of course, the effects of inflation.Economic TheoryThe fundamentals of equipment replacement theory grew out of the interaction between economics, engineering and finance. The use of annual cost comparisons and rate-of return calculations were helpful in handling situations in which assets with different finite lives were being compared. Later developments bringing together the concept of economic life and marginal analysis helped provide additional refinements to the theory. Taylorui showed that the displacement of an aging asset with a similar, but newer, asset can be justified economically when the marginal cost of keeping the asset one more year exceeds the minimum uniform annual cost equivalent of the proposed replacement."

Jan 1, 1980

By K. L. Ford, D. R. Lentz, J. H. Rickard, R. P. Taylor

Abstract - Coupled gamma-ray spectrometric and lithogeochemical studies throughout the Heath Steele Mines area, Bathurst Camp, New Brunswick, indicate that primary and secondary geochemical differences exist between the stratigraphic footwall and hangingwall crystal tuff units which host the massive sulfide deposits. Of particular interest is Th, and to a lesser extent, Zr and Y, which are more concentrated in the hangingwall than the footwall crystal tuffs, whereas the opposite is true for TiO2. This expands on earlier lithogeochemical-chemostratigraphic results concentrated in the eastern part of the Heath Steele belt that led to revision of the local stratigraphy, and necessitated a structural re-interpretation of the area with implications for exploration. Although K depletion (decreased K and K/Th) is typical of chloritized footwall zones of chloritization, these features were not fully apparent here due to the recessive nature of these altered zones. In situ radiometric analysis using a portable gamma-ray spectrometer is a rapid, inexpensive analytical technique for chemostratigraphic characterization of rock units within volcanogenic massive sulfide deposit settings, provided there is a contrast in the distribution of natural radioelements, particularly Th and K.

Jan 1, 1998

By Richard J. Haslinger, C. Mark Rebagliati, James L. Oliver

Abstract - Exploration at the Specogna gold deposit has identified a geological resource of 65.0 Mt grading 1.63 g/t Au, which equates to 3 million ounces of contained gold. This resource is hosted in a low-sulfidation epithermal deposit of Miocene age that is localized along the northwesterlytrending Sandspit fault. The fault has juxtaposed Late Cretaceous mudstone of the Haida Formation to the west, with Late Tertiary coarse clastic sediments and lesser andesitic volcanic rocks of the Skonun Formation to the east. A plagioclase porphyritic dacite dike intrudes the Haida mudstone and Skonun sediments along the fault. Gold mineralization, in hydrothermal breccias, veins and stockworks developed mainly in Skonun sediments and dacite. These are formed in an 800 m long zone that roughly parallels the Sandspit fault. The gold zone is funnel-shaped in cross-section, approximately 300 m wide at surface, 220 m above sea level, and narrows to approximately 50 m, at sea level. The deposit lies within an elongate zone of moderate to intense hydrothermal alteration that, at surface, extends over a known area of approximately 2 km2. Its western extent is bounded by the Sandspit fault. There is an asymmetric alteration zonation, with a core of silicic-potassic (adularia) and smectite-illite clay alteration that is bounded to the east by argillic alteration. Similar zoning defined by the distribution of metals reflects the position of the main feeder conduit. Mineralization of altered wallrock is dominated by 1% to 4% auriferous pyrite and marcasite. Gold and silver occur as electrum; individual silver minerals have not been identified. Other sulfides are rare, and are identified only microscopically. The mineral suite is typical of low-sulfidation epithermal systems. Gold occurs in early, multi-phase, variably bladed and banded quartz veins and breccias, which are cut by barren, single phase, drusy quartz veins.

Jan 1, 1998

By Tim C. Webb

For almost 350 years, industrial rocks and minerals have been produced, used locally and exported from New Brunswick to markets throughout the world. Up until the early 1960s, commodities like grindstone, building stone, gypsum, and limestone served as the foundation of the province's non-fuel mining industry. The importance and high level of activity surrounding industrial rock and mineral development in New Brunswick is reflected in a multimillion dollar industry generating substantial revenue and providing a valuable service to its people. New Brunswick's varied geology is reflected not only by the diversity of industrial rock and mineral resources presently under development but also in several promising exploration and potential development opportunities. The province also hosts several industrial rock and mineral processing facilities, each with established technologies ensuring high-quality products and each with sufficient flexibility to supply customized products for various specialized niche markets. With the imminent availability of natural gas to parts of the province, the prospects for additional value-added processing and re-examination of known, yet presently undeveloped deposits, appear excellent. These variables coupled with the province's advantageous geographical location, highlighting tidewater access to global markets and within one day's trucking distance to a regional market of several million people, guarantee prompt delivery of high-quality products at competitive prices.

Jan 1, 2001

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By Rodrigo Craig Cerello

The Brazilian economy has always presented a strong correlation with the mineral activity. Since colonization days, due to the territorial expansion caused by the explorers search for gold, mining in Brazil became a basic sector of national economy. Currently, the Brazilian mineral sector¹ estimates a 550% production increment (Figure 1A) in the last 10 years, reaching the US$ 50 billion value, reflecting the increased global demand for raw materials from mineral origin. According to the Brazilian Constitution², mineral resources belong to the Federal State and, consequently, their exploitation must be authorized, under penalty of engendering federal crime. Furthermore, activities of this nature are prone to cause environmental degradation such as, but not limited to, deforestation, pollution, soil deterioration and water contamination. The GPEMA represents the forensics group of the Brazilian Federal Police responsible for the technical analysis of traces related to crimes against the environment and consequently, illegal mining cases.

Aug 1, 2013

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By Iina Vaajamo, Jani Jansson, Lauri Pesonen

In pyrometallurgical operations, structural integrity of a high temperature furnace plays a crucial role in the overall safety, profitability and ecological footprint of the plant. Furnace integrity is related to how reliable a furnace is and it can be compromised, for example, by having poor operating and maintenance practices, an inefficient cooling system and flaws in the overall furnace design. These flaws and poor practices might lead to unexpected shutdowns, production losses, increased emissions, or worse. This paper presents the main factors to consider when engineering a furnace and developing its operating practices, while ensuring safe and reliable operations without compromising process efficiency and quality of the final products. In this respect, Outotec’s solutions for the cooling system and for automation systems like PROSCON, Process Advisor, Sentinel and our Smelting Information Management System, are also introduced.

Jan 1, 2015

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By G. Minhas, M. Pule, Y. Laffitte, M. c. McGurn, T. Tzanetakis, Peacey. J., R. Susilo

Titanium (Ti) metal production from titanium tetrachloride (TiCl4) using magnesium (Mg) as a reducing agent is the well-known Kroll process. A chloride route is used to avoid oxidation of the titanium sponge. The sponge is consolidated into ingots and can then be made into powder by melting and atomizing or by hydriding/dehydriding. Attempts at direct powder production have met with difficulties, including low Ti yield and the formation of very fine particles (particles between 25-100 µm are desired). This paper discusses two methods to produce Ti powder in a molten salt medium using magnesium powder as a starting material instead of a pool of molten magnesium. The first method is a direct reduction of gaseous TiCl4 injected in the melt with the magnesium powder in suspension in the molten salt. The second method is a two stage TiCl4 reduction reaction where recycled Ti was used to form titanium dichloride (TiCl2) in the first stage followed by addition of magnesium powder into molten salt in the second stage. A correlation between Ti yield and processing variables such as TiCl4 to Mg ratio, Mg particle size, TiCl2 concentration in the melt, and reaction temperature was studied. The Ti powder formed was also analyzed for particle size distribution. Despite challenges and difficulties encountered, this paper shows some promising results which could provide guidance to others working on direct Ti powder production.

Jan 1, 2015

By J. Zhang, T. Oleniuk

It is well-known that Saskatchewan has the world’s richest uranium deposits and advanced processing technologies. Unlike the Saskatchewan deposits, complicated mineralogy is common for other places in the world. Mineralogy dictates the process. Mineral Processing at the Saskatchewan Research Council has been working with the uranium industry worldwide since its inception to develop effective processing technologies to suit the unique mineralogy of each deposit. This paper reviews the research and development of uranium processing technologies in the current major uranium production areas such as Canada, as well as the potential development regions like Argentina and Sweden. Acidic and alkaline leaching processes, as well as by-product recovery technologies are discussed based on mineralogy.

Jan 1, 2020

By A. J. Hargraves

"It is difficult to quantify comparatively the gassiness of a property. The most common index to gassiness, cubic feet of gas per ton of coal mined, is very arbitrary and does not take into account the geological setting nor the mining operation. The gassiness of a virgin coal in situ can be assessed, but no method is precise and the most accurate methods involve prolonged field and laboratory experiments. In general, gassiness increases with depth. Whereas 'gas' normally implies methane, other gases such as nitrogen, carbon dioxide, etc. may be present in seam gas also. The inflammability of methane is a problem, particularly the explosibility of a methane-air mixture; also oxygen dilution is involved in high gas concentrations and some gases are poisonous even in low concentrations. Cross measuring into a virgin seam is usually not as troublesome as development in the seam, where narrow openings may require strong ventilation to dilute gases exuding from the face and sides. Total extraction presents problems of gas from the working seam, or from adjacent seams, particularly at the return side, or of gas-laden air from the goaf streaming out or sometimes surging out intermittently, again on the return side. In pillar extraction or longwall retreating special roadways may be required to allow the side-to-side and end-to-end flushing of the goaf which is somewhat inherent in longwall advancing. Layering may occur, particularly where ventilation conditions are not brisk. Outbursts of gas from adjoining seams may be induced by sudden rupture of roof or floor in caving workings. Outbursts of coal and gas from the working seam may occur, mostly in development work, under special environmental circumstances. Gas problems may be reduced or eliminated by predrainage of gas ....:. rarely successful from the working seam - usually undertaken from adjoining seams prior to escape of gas released by caving. The ideal solution - general predrainage of gas to the surface from measures prior to mining - has yet to be accomplished. • In the planning of gassy mines it is possible to make an assessment of gas contained in the seams and to estimate what proportion will be released into the mine air, but emission of gas into mine workings is never steady and at present there is no better planning criterion than experience at the mine next door!"

Jan 1, 1973