Search Documents

By S. S. Sephton, Kirit C. Vyas, Melvin J. Greaves

Energy requirements for various pelletizing systems are considered from a fuel and power aspect, with the presentation of typical energy heat balance flow sheets. A partial calculation for the firing zone of a straight grate system is shown and a comparison of an actual measured and a theoretical-calculated heat balance for a grate-kiln is presented. The power used for each pelletizing system and future possible energy savings a1•e also reviewed.

Jan 1, 1976

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By F. Crundwell, N. Steenekamp

"The leaching of sulphide minerals generates a significant amount of energy. There are three systems that might be used to remove this energy. These are: cooling coils, quench water, and flash recycle. Flash recycle is the recycling of slurry from the autoclave to the feed tank. Heat is removed in this arrangement when the slurry at elevated temperature and pressure is flashed to atmosphere, releasing steam. The slurry is returned to the autoclave at lower temperature, resulting in cooling. The cooling is directly proportional to the steam released from the recycled slurry. Design equations and results for the flash recycle system are presented. A fourth proposal for removing heat is to recycle slurry from the back of the autoclave. These four alternatives not only remove the heat, but also have an effect on the leaching efficiency. Amongst the four alternatives, design calculations indicate that the flash recycle option is the optimal solution in terms of leaching efficiency and heat removal, and recycling product from the back of the autoclave is the worst. In spite of its efficiency in terms of heat removal and leaching, the implementation of the flash recycle system is limited to a few operations in the platinum industry.INTRODUCTIONIn considering ways to improve leaching operations, focus is placed on the chemistry, on the kinetics, the agitation and perhaps even on the gas mass transfer conditions. Attention is less frequently placed on the removal of energy from these reactors and how this might limit performance.The pressure leaching of sulphides releases a significant amount of heat. For example, the reaction for the leaching of chalcocite, Cu2S, given by"

Jan 1, 2012

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By C. Stapel, P. D. Roberts, D. G. Jones, W. G. Macdonald, R. J. De Meijer

"Abstract-Measurement of natural radioactivity has been used in both a qualitative and a quantitative way in mineral exploration, particularly in the search for uranium. In the last five years, the Kernfysisch Versneller Instituut (KVI) and British Geological Survey (BGS) have designed, built and tested a new detector system that greatly improves quantitative applications in mineral exploration, especially on the seafloor and in the nearshore zone. The new system is an enhancement of an earlier BGS design. The major improvements comprise the use of a highly sensitive ?-ray detector, together with new data processing, from which concentrations of natural radionuclides may be deduced in real time. After laboratory analysis of samples, these concentrations can be converted into mineral percentages. Once the mineralogy of an area has been characterized, this conversion can also be done in real time.Thus far the system has mainly been used to map heavy-mineral concentrations in coastal subtidaland intertidal sediments. For such work the multi-sensor detector probe is towed on the seafloor and various parameters are recorded continuously. The probe contains, in addition to the gamma-ray detector, a water-pressure sensor (giving water depth) and an acoustic device to measure bottom roughness. The system, when used together with high-precision positioning systems such as D-GPS, enables the production of detailed maps of bathymetry, bottom roughness, and seafloor radioactivity or mineral distribution. These maps allow mineral concentrations to be readily correlated with seabed topography and sediment type. In the same way, ?-ray detectors could be used advantageously during dredging operations to provide on-line assessment of the mineral content of the dredged sediment as well as to guide the direction of dredging. Additionally, the same technique could be used to monitor the subsequent fate of a dredge spoil after dumping on the seafloor.Natural radioactivity arising from potassium and the thorium and uranium decay series has potential use for the fast and reliable assessment of siliciclastic and phosphatic impurities in limestones. Detection of such impurities may preclude the use of the limestone for chemical or cement production.Apart from its use in exploration, the technique has significant potential in mineral processing, particularly of heavy minerals. It can be applied as on-line quality control in dry and wet separation processes and for process control, by using decisions based on the results to control valves and other instrumentation. In addition, it can also be used in environmental monitoring of waste arising from mineral extraction and processing. In conclusion, the technique described has a diversity of applications in exploration, mining and mineral processing."

Jan 1, 1997

By C. Stapel, P. D. Roberts, D. G. Jones, W. G. Macdonald, R. J. De Meijer

"Measurement of natural radioactivity has been used in both a qualitative and a quantitative way in mineral exploration, particularly in the search for uranium. In the last ?ve years, the Kernfysisch Versneller Instituut (KVI) and British Geological Survey (BGS) have designed, built and tested a new detector system that greatly improves quantitative applications in mineral exploration, especially on the sea?oor and in the nearshore zone. The new system is an enhancement of an earlier BGS design. The major improvements comprise the use of a highly sensitive ?-ray detector, together with new data processing, from which concentrations of natural radio nuclides may be deduced in real time. After laboratory analysis of samples, these concentrations can be converted into mineral percentages. Once the mineralogy of an area has been characterized, this conversion can also be done in real time.Thus far the system has mainly been used to map heavy-mineral concentrations in coastal subtidal and intertidal sediments. For such work the multi-sensor detector probe is towed on the sea?oor and various parameters are recorded continuously. The probe contains, in addition to the gamma-ray detector, a water-pressure sensor (giving water depth) and an acoustic device to measure bottom roughness. The system, when used together with high-precision positioning systems such as D-GPS,enables the production of detailed maps of bathymetry, bottom roughness, and sea?oor radioactivity or mineral distribution. These maps allow mineral concentrations to be readily correlated with sea-bed topography and sediment type. In the same way, ?-ray detectors could be used advantageously during dredging operations to provide on-line assessment of the mineral content of the dredged sediment as well as to guide the direction of dredging. Additionally, the same technique could be used to monitor the subsequent fate of a dredge spoil after dumping on the sea?oor.Natural radioactivity arising from potassium and the thorium and uranium decay series has potential use for the fast and reliable assessment of siliciclastic and phosphatic impurities in limestones. Detection of such impurities may preclude the use of the limestone for chemical or cement production.Apart from its use in exploration, the technique has signi?cant potential in mineral processing, particularly of heavy minerals. It can be applied as on-line quality control in dry and wet separation processes and for process control, by using decisions based on the results to control valves and other instrumentation. In addition, it can also be used in environmental monitoring of waste arising from mineral extraction and processing. In conclusion, the technique described has a diversity of applications in exploration, mining and mineral processing."

Jan 1, 1997

By B. Meddings, O. J. I. Evans

"This paper is mainly concerned with the present and probable future role of hydrometallurgy in the production of base metals.The economic and technological bases of the hydro-metallurgical plants built and operative in the mid-fifties are compared to those in production in the mid-sixties. The trends observed are extrapolated and some estimates made concerning the probable size and type of hydrometallurgical plants which will be operative in the mid-seventies.The impact of emerging socio-economic factors such as pollution control and the market demand for specialized metal products which favour hydrometallurgical recovery processes are also discussed."

Jan 1, 1971

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on 'The Mechanism of the Surface Phenomena of Flotation', showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By Roy S. Celland, K. H. Singh

The introduction of 'post' pillar mining at the Strathcona mine represents a new approach to ground support in cut-and-fill applications. The method has also shown significant economic advantages. It is believed that the development of this concept is one of the few examples where rock mechanics principles have successfully been applied in the development of a stoping method. The paper describes the evolution of this method and contains discussions on the theoretical analysis of the technical, operational and economics aspects of the system. Pillar design procedures and field observations on the practical application of theoretical analysis are also outlined.

Jan 1, 1973

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit 'dry' drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By A. A. Wessels, D. P. Allison

"Mine hoists are built to handle a certain nameplate capacity; they are specified and designed according to the required duty. However, as production capacity increases in other parts of an operation, the hoist capacity can become the critical constraint. Such a situation occurred at Lundin Mining’s Neves-Corvo operation. This paper examines how each component of the existing hoisting system was examined and optimized. Through a combination of engineering study and hoist simulations, the annual hoisting capacity was improved by 24% through increases in payload capacity and available hoisting time combined with a reduction in cycle time, while no changes were made to the hoist motor, drum or headframe. The additional payload capacity was achieved by reducing the mass of the hoist ropes and skips, and improving load monitoring systems. The cycle time was reduced through the shortening of the creep distances and increased availability through the installation of a shaft collar safety platform, alternative guide rope bushes, and superior liners for both the skips and underground measuring flasks. Enhanced cooling of the hoist electrical system was also incorporated to increase hoist availability by reducing downtime during hot summer months. The changes will increase the capacity from the current 4.5 mega tonnes per annum (Mtpa) to a planned 5.6 Mtpa and are being implemented over a 2-year period whilst maintaining the mine production during the upgrade work. INTRODUCTION Neves-Corvo Mine Neves-Corvo is primarily a copper and zinc mine producing copper, zinc and lead concentrates. The operation is owned and operated by Somincor, the Portuguese subsidiary of Lundin Mining. Located in the Alentejo district of southern Portugal, the operation is situated approximately 15 km southeast of the town of Castro Verde, where summer temperatures can reach as high as 45ºC, and approximately 220 km southeast of Lisbon. The principal means of mine access is via a ramp from surface, with the vertical shaft used to hoist ore and waste from the 700 m level, while conveyors descend from the 700 m level to transport ore and waste up from the deeper levels of the mine. The mine is highly mechanized and several different stoping methods are employed, with the most significant being bench-and-fill and drift-and-fill. The Neves-Corvo mine currently exploits five orebodies: Neves, Corvo, Graça, Zambujal and Lombador for copper and zinc-lead ores which are processed in one of two plants. All the orebodies are currently exploited over their full elevation with the exception of Lombador which is only mined down to the 220 m level, approximately the top 50% of the orebody, known as Lombador Phase 1."

Jan 1, 2019

By D J. Murray

This paper outlines the principles of friction hoisting and the components involved, and gives a description of a specific mine hoist. Friction hoisting is compared with conventional drum hoisting, and the depth of shaft at which friction hoists become more economical than drum hoists, with respect to power consumption, is determined. Introduction T HE purpose of this paper is to outline the principles of friction hoisting, to describe the components and to show the advantages of multi-rope friction hoisting. Some calculations are made to show that the power requirements and the initial costs of friction hoists are less than those of conventional drum hoists, once a certain depth of shaft has been reached. The use of multi-rope friction hoists is gradually superseding the employment of the conventional drum hoist in many parts of the world. It results in heavier payloads from deeper levels, an increase in shaft safe-ty and a more compact installation for protection against adverse weather conditions. It was observed that where drums and friction sheaves exceeded 30 feet in diameter, a number of mechanical disadvantages were being experienced;

Jan 1, 1965

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016

By C. R. Julian

MECHANIZATION During the last fifteen years, numerous attempts have been made to mechanize the operations of loading ore and placing till. It is to be regretted that, to date, little progress has been made in this direction. The comparative efficiency of manual labour in Spain is the factor largely responsible for the failure to cheapen costs by mechanization. The necessity for careful classification of the ore and the need for keeping all openings small also makes the problem one of difficulty. It may be of interest to describe the various attempts at mechanization that have so far been made. CONVEYORS: (1) When stoping by layout III in San Dionisio, a trial was made of transporting the filling by jigging conveyors. This method proved un-economical, as the wall building and spreading of the till could not keep pace with the delivery, with the result that the machinery was idle a great part of the shift. (2) The transport of ore from the working places to the ore-passes by jigging conveyors and belts was also tried. Although more successful than in the case of the fill, the method could not compete with that of hand tramming, principally due to the high cost of (a) maintenance caused by the abrasiveness of pyrites, and (b) labour constantly employed on re-aligning the conveyors owing to the constant settlement of the floor. In a few cases, where a sill floor was being blocked out in virgin ground, the method showed a saving. SCRAPERS: Frequent attempts at loading by scrapers have been made, but again the only success obtained has been in the blocking-out of sill floors. The principal obstacle to the successful application of scraping, other than on the sill floor, has been that the openings, which have to be small, call for a light scraper outfit, whereas, in practice, a heavy scraper and at least a 25 h.p. winch are necessary for handling satisfactorily the ore, which is heavy and which breaks somewhat blockily.

Jan 1, 1940

By J. G. Cullain

Inco Limited is an integrated mining, smelting, refining and manufacturing company with operations located worldwide. The Ontario Division operations consist of 13 mines and 10 processing facilities located in Sudbury, Port Colborne and Shebandowan. The scope of our utilization of energy in the Ontario Division in 1976 included in excess of 2.2 billion kilowatt hours of electric power, 12 billion cubic feet of natural gas, 60 million Imperial gallons of residual oil and smaller quantities of other fuels. In addition to the primary energy consumption, waste-heat energy is recovered in various operations throughout the Division, thereby reducing our primary energy requirements. Total expenditures for primary energy alone in 1976 exceeded 60 million dollars. Energy management studies were initiated by Inco's Utilities Department in late 1972, and resulted initially in a program of electric power cost reduction. This program produced significant results by improving the use of the water available for our hydraulic generation facilities and by a comprehensive peak reduction program. Our experience showed that a program of peak power control creates an awareness of both peak and energy costs, and thereby encourages a general reduction in the electric energy consumption as well as lowering the peak demand. Energy management is a continuing program at Inco and, recently, a formal energy management policy and program was instituted. Energy management committees were formed in each plant or mine area to identify the major areas for energy; consumption, thereby isolating areas with large potential energy losses, and determining immediate action which will improve the energy efficiency or reduce the energy waste within their respective areas. A decentralized program with good cross-communication between all committees was felt to be the best method of providing an on-going effective energy management program. In the future, the projections of dwindling fossil-fuel supplies in Canada and the resultant spiralling energy costs will further emphasize the need of sound energy management practices for all Canadian industry.

Jan 1, 1977

By K. Baris

Methane (CH4) present in coal seams, generally known as Coalbed Methane (CBM), Coal Mine Methane (CMM) or Coal Seam Gas (CSG), is a major energy source, as it is the primary constituent of natural gas. At the same time, released methane is a potent greenhouse gas (GHG) and a major safety hazard in underground mining operations. Therefore, a considerable effort has been undertaken to develop coal bed methane extraction and utilization technologies that can achieve both environmental and safety benefits. Countries with significant coal reserves and gassy seams, i.e., USA, Australia, Canada, China, India, Poland and Germany have developed mature methodologies and practices to extract, before and during mining, and utilize significant amounts of methane from coal seams. Nevertheless, on a global scale, methane recovery remains untested and many technical and economic challenges require urgent attention. The research presented in this paper, sponsored by the United States Environmental Protection Agency (EPA), is focused on the Zonguldak Basin, the only hard coal region in Turkey. The basin is known to contain very gassy coal seams and consists of three major regions: Armutcuk, Zonguldak and Amasra. Among the three, the Amasra coalfield is considered as the most favorable for CBM recovery, as it comprises of deeper coal seams and where a private company, Hema Enerji A.S. (Hema) is already developing coalbed methane production facilities. This study aims at developing a reservoir model to predict the potential CBM recovery from the CBM-2 well, the only producing CBM well drilled by HEMA Enerji A.S in the Amasra coalfield. History matching was utilized to model the 15-day production data and uncertainty analysis was performed to estimate the optimum values for the reservoir parameters. The produced model yielded an average production rate of 143 m3/day for 10 years. The total amount of CH4 to be produced during this period was 0.53 million m3. Furthermore, the total amount of GHG to be avoided was estimated at 6585 tCO2e.

Aug 1, 2013

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973