Search Documents

By T. H. Janes

"IntroductionSULPHUR is a constituent of many industrial products. It is part •of almost anything we eat, wear, or use. In fact, sulphur is so important that there has been an increasing tendency in recent years to measure industrial growth in terms of sulphur consumption.The uncertainty of obtaining adequate supplies •of elemental sulphur from the Frasch-mined domes. of Texas and Louisiana in the United States led all countries in 1950 to seek alternative sources of supply of this necessary element.Canadian industry has been supplied, for many years, with most of its sulphur requirements by United States Frasch-mined sulphur. World demand for this sulphur has necessitated the imposition of controls on its distribution, as production has not kept pace with demand. Until the third quarter of 1950, Canadian manufacturers of pulp and paper, heavy chemicals, explosives, and textiles •experienced little difficulty in obtaining their needs of elemental sulphur from the United States. However, at that time, low producers' stocks and declining reserves threatened to reduce shipments from producers, with the prospect of a continuing shortage for some time. These conditions, together with higher prices, stimulated the search for alternative sources of supply in Canada."

Jan 1, 1952

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By T. Mulja, Michel Boily, Anthony E. Williams-Jones, Pierre Pilote

"The Preissac-Lacorne batholith is composed of suites of early metaluminous calc-alkalic gabbroic to granodioritic intrusives, three late peraluminous monzogranite plutons and numerous Li, Be and Ta-bearing granitic pegmatites. The Lacorne pluton is dominated by biotite and biotite + muscovite monzogranites containing abundant Be and Ta-bearing granitic pegmatites (40-80% volume). The pluton is surrounded by swarms of unzoned or poorly zoned spodumene-rich pegmatite dykes. The La Motte pluton is composed of biotite monzogranites, biotite+ muscovite monzogranites and rare muscovite + garnet monzogranites. Li, Be and Ta-bearing pegmatites are less abundant than in the Lacorne pluton and are commonly associated with molybdenite bearing quartz-muscovite-K-feldspar veins. In the Preissac pluton, muscovite + garnet monzogranites and muscovite + biotite + garnet monzogranites are the dominant rock types. The pluton rarely contains granitic pegmatites and these are generally barren. However, numerous molybdenite bearing quartz and quartz-feldspar-muscovite hydrothermal veins are observed.Li, Be andTa-bearing pegmatites display a crude spatial zonation around their parent monzogranites. Spodumene-rich pegmatites are generally unzoned or poorly zoned and are confined to the surrounding metasedimentary or metavolcanic rocks or crop out in the early gabbroic to granodioritic intrusives surrounding the monzogranites. Ta and Be-bearing pegmatites are usually concentrated towards the margins of their parent monzogranites. The highly fractionated nature ofmonzogranites (high Rb/Sr, low K?Rb, Ba?Sr, Zr/Nb ... ), their peraluminous composition (corundum normative and muscovite bearing) and the numerous occurrences of Ta and Be-bearing pegmatite dykes represent important criteria for the exploration of fertile granites."

Jan 1, 1990

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By M. Kumral, E. Dilhuydy, B. Ozdemir

"In-pit crushing and conveyor (IPCC) systems have become increasingly popular in the mining industry as an alternative to truck-and-shovel systems. Deciding whether to haul waste rock by truck or IPCC represents an important gap to be investigated in semi-mobile IPCC systems. A cost analysis is presented to evaluate the feasibility of crushing and conveying waste material in IPCC systems, along with sensitivity and risk assessments through Monte Carlo simulation. Although the capital expenditure is higher, results showed waste crushing will be feasible in deep pits and over long mine life and haul distances.RÉSUMÉ La popularité des systèmes de concassage et de transport dans la fosse minière (IPCC, de l’anglais In-pit crushing and conveyor) n’a cessé de croître dans l’industrie minière ; ils constituent en effet une option intéressante de remplacement des systèmes par camions et pelles mécaniques. Le choix entre le transport des stériles par camions ou par IPCC est encore difficile à faire et devra faire l’objet d’une étude approfondie au niveau des systèmes d’IPCC semi-mobiles. Une analyse des coûts est présentée pour évaluer la faisabilité du concassage et du transport des stériles par les systèmes d’IPCC, de même que des évaluations de la sensibilité et des risques par le biais de la simulation de Monte Carlo. Si les dépenses en immobilisations s’avèrent être plus élevées, les résultats ont cependant montré que le concassage des stériles sera envisageable dans des fosses profondes ainsi que sur une longue durée de vie et de longues distances de transport. INTRODUCTIONThe mining industry is currently facing many challenges such as low commodity prices, increasing environmental concerns and regulations, lower grades, deeper mines, and greater waste-rock quantities. As a result, the profitability of mining operations has decreased, with many mines stopping or suspending operations, and many new projects being postponed. Mining companies have therefore focused on improvements and innovations to increase the cost effectiveness of operations, for example, increasing production capacity to take advantage of the economies of scale (Crowson, 2003) and decreasing the unit operation cost. Changes in production capacity force mining companies to evaluate alternative material handling systems.During the past few decades and within material handling systems, significant improvements have been made to truck performance and capacity. Consequently, operating expenditures (OPEX) associated with fuel and maintenance have risen swiftly. In a mining operation, truck hauling systems now represent 40–50% of the capital cost and approximately 45% of the OPEX (Tutton & Streck, 2009). Additionally, material transportation costs are expected to increase due to longer haul distances arising from deeper and larger mines (Fleet et al., 2015). Finally, large fluctuations in fuel prices result in high risks associated with truck OPEX. According to the United States Energy Information Administration (2015), the cost of crude oil—the largest component of the retail price of diesel fuel—increased from US$24.31/barrel in 1986 to US$46.92/barrel in 2016, peaking at US$151.72/barrel in 2008 (Macrotrends, 2016)."

Jan 1, 2017

By C. H. Buck, A. J. Taylor

"In 2015 Vale’s Clarabelle Mill began the process change to enable a higher degree of Cu separation. The flowsheet modification was part of a complete divisional flowsheet change being implemented in Vale’s Sudbury Operations. This paper will centre on some of the Operational Readiness (OR) work, culminating in the commissioning of the circuit in March 2017. The emphasis will be on the implementation of an integrated test plan to prepare for the process flow change through the mill.BackgroundClarabelle Mill (CBM) began making a saleable Cu concentrate in 2006 with the installation of the Cu separation circuit. Typical separation rate was 35-40% of Cu in feed reporting to Cu concentrate based on a target Ni concentrate Cu:Ni target of 0.7-0.8. The remainder of the recovered Cu (55-60%) reported to Ni concentrate and was smelted through the Copper Cliff Smelter.In 2013 a capital project, Surface Facility Upgrade (SFU), was implemented to focus on matching the surface plants capacities with the future mine plan to maximize revenues. This was to be achieved by redistributing the metal flow, specifically Cu, through CBM to increase metal unit content through the Smelter. The amount of redistribution of Cu was determined to be based on maintaining a stable Cu to Ni ratio (Cu:Ni) in the Ni concentrate.The change in Cu:Ni ratio in the Ni concentrate would affect the Sudbury divisional flowsheet, and required process changes across the all of the surface plants. The detail that surrounds the flowsheet changes as a whole will not be discussed, but the outcome of the decisions plays a large role in the operational readiness interactions between the mill, its suppliers and its downstream customers."

Jan 1, 2018

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By William E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential.INTRODUCTIONThe purpose of this paper is to describe a cost approach to the valuation of mineral exploration properties and to provide some valuation examples. The particular cost approach described is the Appraised Value Method, which is best applied to mineral properties at the exploration stage.At present there are no comprehensive regulations or guidelines in Canada which specify what approaches and methods to use for the valuation of mineral properties. In this paper, the Appraised Value Method described is one method that the writer considers to be accepted industry practice for mineral properties at the exploration stage.Mineral properties are valued for a number of reasons, including mergers and acquisitions, non arm's length transactions, pricing of initial public offering of stock, support for property agreements, litigation, expropriation, and insurance claims."

Jan 1, 2003

By A. Broussaud

The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance. The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness. The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock? rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill? system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase. The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones.

Jan 1, 2012

By Claudia Gasparrini

"The ore microscope and electron microprobe, two common instruments for academic research, have not been used to full advantage in the Canadian mining industry, perhaps because they are not readily available to most mining companies.The present paper gives a description of the two instruments and of the manner in which, when used together, they contribute to the identification and description of mineralogical and metallurgical samples, and reviews the applications, to . date, in the mineral industry.The metallurgical applications can assist in determining the best separation technique for a particular metal or other economically important element, can provide explanations for poor recovery and/or liberation, can be used to determine theoptimum concentrate grade and can indicate environmental problems that may arise from the extraction process.In certain cases, the use of the two instruments may assist in the evaluation of new mineral deposits and in the determination of the origin of mineralization.IntroductionThe ore microscope and electron microprobe, two widely used instruments in universities and other research institutions, have not been exploited to their full potential by the Canadian mining industry.High-magnification, high-resolution ore microscopes, owned by most Canadian universities and government mining branches, are not widely used by mining organizations. The situation is very much the same with the microprobe. The geology departments of several major Canadian universities have easy access to this instrument. Fifteen of them, to the author's knowledge, own one and a few have already acquired or are planning on acquiring a second and later model. The mining branches of the Canadian Government have similar easy access to microprobes, as at least four of these instruments are available to them in Ottawa alone. The mining companies, on the other hand, except for the few larger ones which have their own research laboratories, have not been able to take advantage of electron microprobes in the past.This failure to exploit good ore microscopes and electron microprobes has been mainly due to a lack of expertise in the use of the two instruments for the study of metallurgical problems related to ore mineralogy. Government institutions providing research and test work to the industry are few in number, and are not always equipped with these instruments or are not geologically-oriented. Information provided on a consulting basis by universities and by government mining branches is normally limited, and frequently is not oriented to the needs of the mining company."

Jan 1, 1980

By H. O. Lien

Among the known iron deposits in Canada, many are of low grade and require beneficiation to produce an acceptable blast-furnace feed. Some of the deposits have never been considered for commercial exploitation due to the lack of a suitable concentrating process. A number of deposits of this type are located in Northern Ontario. The problem in upgrading these deposits is three fold. Firstly, the iron occurs as a mixture of magnetite and hematite. Secondly, the grain size of the material can be fine to very fine. Thirdly, the complex mixture of gangue minerals, which consists invariably of silica, flaky silicates and carbonates, slimes excessively on fine grinding. Algoma's efforts to concentrate these iron-bearing materials culminated in the development of a "Selective Flocculation and Desliming Process" employing slimes removal as the sole beneficiation technique. The process was applied successfully in the laboratory using two stages of grinding and a total of seven deslimings. Prior to the removal of slimes, the iron-bearing fines were selectively flocculated from a thoroughly dispersed pulp using a modified starch as flocculant, Sodium silicate was employed as dispersant. An attempt was made to optimize some of the process variables using material from one specific iron formation near the town of Geraldton in Northern Ontario. The preparation of the starch proved most critical. This matter, and the method used to evaluate the degree of breakdown of the starch molecule, are therefore discussed in some detail.

Jan 1, 1978

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

By R. N. Chakravorty, K. K. Feng

"There is growing evidence that modern methods of mining coal increase the risk of spontaneous combustion. Seemingly unimportant at this time, this hazard could prove to be a barrier to growth and development of the coal industry in some areas of Canada. The paper presents bedrock knowledge on spontaneous combustion gathered by scanning and evaluating current technical and research literature. Special efforts have been made to identify significant coal and environmental factors and to establish criteria for susceptibility. In addition to the state-of-the-art knowledge, preliminary results from on-going studies are discussed."

Jan 1, 1973

By Brandt Porter, Lawrence K. Nordell, Alexander Potapor

"Improving comminution efficiencies with better machine geometries and motions, improved nip angles, rock movement control, and voids regulation among rocks are some of the next steps to better machine performance. Recent gains (~30%) using high pressure grinding rolls (HPGRS) and vertical roller mills, in theory and practice, are based on Prof. Klaus Schönert’s academic studies (1979–1996) on rock breakage physics. More recently, University of British Columbia Prof. Bern Klein’s studies (2006–present) via the Ph.D. thesis of Z. Davaanyam (2015) further validate theory with practice from laboratory measurements used in this paper.They demonstrated ideal rock compression breakage, within HPGR and vertical roller mill machines using a piston-die apparatus. Similar rock size range is used. The piston-die confine rock breakage behavior. However, these studies do not extend to larger rocks (> 75 mm), and do not demonstrate the influence of rock voids among bifurcation of rocks during comminution. Further, machines fed with larger rock sizes, such as gyratory, jaw, and cone crushers, are not designed or evaluated for geometry nip angle efficiency.Herein we illustrate a performance gain of a new comminution machine, the conjugate anvil-hammer mill (CAHM), first presented at SAG 2011 (Nordell, 2012). The CAHM machine digests rock sizes 400% larger than HPGR, improves rock grip/nip geometry, better improves rock voids, improves surface wear life > 500%, and improves rock containment and slippage during compression. In all, the CAHM machine shows 22 potential improvements over the HPGR. Most importantly, CAHM shows a 50% kWh/ton improvement compared to the HPGR. Our studies use an advanced Discrete Element Method (DEM) computer program called ROCKY. ROCKY simulates moving boundaries, surface wear mechanics, and incorporates rock breakage physics based on the fundamentals of JKMRC T10 protocol [×] with tuned A × b breakage parameters.We calibrate rock breakage in our DEM code to mimicking both UBC laboratory piston-die and HPGR comminution measurements. We then model CAHM with these known ore and machine properties. Differences are illustrated using DEM techniques on each machine, including key points of when each: use geometry; initiate bifurcation breakage; provide a map of particle size distribution by location; illustrate the importance of controlling voids to minimize agglomeration after breakage; machine performance limits; and kWh/ton benefit."

Jan 1, 2016

By C. Gosselin, M. Rheault, M. Benoit, Y. Bouroubi, V. Sarago

The last three decades have seen significant mining development in northern regions of Canada, where the freeze and thaw cycle of permafrost and the corresponding surface subsidence and heave represent a significant challenge to the design and maintenance of infrastructures. Identifying areas at risk is of great assistance to reduce the impact of this issue. Over the past ten years, Synthetic Aperture Radar Interferometry (InSAR) has been widely used to monitor ground surface deformation. With this technique, changes in phase between two SAR acquisitions are used to detect centimeter to millimeter surface displacements over a large area and with high spatial resolution. InSAR can be used as a tool to assist the siting and design of new infrastructure as well as highlighting the risk to existing structures in areas of unstable terrain. This paper presents the results of a project carried out by Effigis, which made use of SAR interferometry in the context of monitoring terrain and infrastructure stability in a northern mining environment that is affected by permafrost seasonal and long term changes. TerraSAR-X images acquired during two periods, August to November 2012 and March to October 2013, were used to measure the deformations and/or movement of ground surface, infrastructure and stockpiles caused by seasonal changes in permafrost extent in and around a mining site located in Nunavik, Quebec. The results showed that spatial and temporal distributions of surface displacements are in accordance with scientific and terrain knowledge. Some displacements were observed in loose soil areas while, as expected, none were detected in bedrock and rock outcrop areas. The areas most affected by active layer changes showed surface subsidence in the thaw settlement period. This study confirms that SAR interferometry has a great potential for operational applications related to risks induced by surface deformation in mining environments. It shows that this technique can be used to produce reliable maps of surface movement and monitor the vertical displacement of important infrastructure.

Jan 1, 2015

By O. Rabeau, M. Legault, F. Fallara

"Abstract - The development of robust 3-D geological models involves the integration of large amounts of public geological data, as well as additional accessible proprietary lithological, structural, geochemical, geophysical, and diamond drill hole data. 3-D models and maps have been available, particularly in the petroleum industry, for more than 10 years. Here, we demonstrate how robust 3-D maps can be used as interactive tools for mineral deposits exploration. In particular, we show how the interrogation of 3-D data sets can constrain exploration targets at depth. The main advantages of this technique for the mining industry are the homogeneity of data treatment and the validation of geological interpretations, taking into account geophysical and geochemical data. Data integration and cross-correlation of geology and geophysics can be achieved in two dimensions in any good GIS package. However, the added strength of 3-D analysis is the integration of separate data sets in three dimensions to build more complete, more realistic models, and in delineating areas of high economic potential at depth. Furthermore, these models can be modified and improved at any time by adding new data from ongoing drilling and geoscientific surveys. This paper presents two examples of 3-D models used for mineral exploration: the Joutel VMS mining camp and the Duparquet gold camp, Quebec. In both examples, the creation of the model is discussed and queries specific to the relevant exploration model are introduced. Eight potential exploration targets are generated at Joutel and seven at Duparquet. Although the targets defined are dependent on the details of the chosen queries, it is apparent that this technique has the potential to generate promising exploration activity that can engender new targets. Sommaire - Le développement de modèles 3-D géo-intégrés fiables implique l’intégration de grandes quantités de données géologiques publiques ainsi que des données lithologiques, structurales, géochimiques, géophysiques et de forages en provenance du secteur privé. L’industrie pétrolière dispose de modèles et de cartes 3-D depuis plus de 10 ans. Ce manuscrit présente un exemple d’utilisation de modèles et de cartes tridimensionnels détaillés comme outils interactifs dans l’exploration de dépôts métallifères. L’emphase est mise sur le processus d’interrogation des données en 3-D pour la définition de cibles d’exploration en profondeur. Les avantages principaux de cette technique sont l’uniformité du traitement des données et de la validation des interprétations géologiques, tout en tenant compte des données géophysiques et géochimiques. L’intégration de données et la corrélation de la géologie et de la géophysique peuvent être accomplies en deux dimensions dans n’importe quel logiciel SIG. La plus grande force de l’analyse 3-D demeure cependant la possibilité de construire des modèles complets et réalistes permettant de cibler des secteurs à haut potentiel économique en profondeur. De plus, ces modèles peuvent être modifiés et améliorés de manière interactive en ajoutant de nouvelles données provenant de forages et de levés géoscientifiques en cours. Ce manuscrit présente deux exemples de modèle 3-D géo-intégrés développés pour l’exploration minérale : le camp de SMV de Joutel et le camp aurifère de Duparquet, Québec. Dans les deux cas, la construction du modèle est décrite et les requêtes spécifiques à chaque type de gisement sont présentées. L’exercice a permis de définir huit cibles d’exploration potentielles à Joutel et sept à Duparquet. Bien que les cibles identifiées dépendent des contraintes utilisées pour les requêtes choisies, cette technique permet de générer de nouvelles cibles qui pourraient relancer l’activité d’exploration dans les camps miniers " matures " ou dans des secteurs moins explorés."

Jan 1, 2006

By Hans Lundberg

PREFACE THE successful conclusion of all geophysical work depends on the operator's skill and sound judgment, as well as on his knowledge of geology and geophysics. We have been fortunate enough to have as co-workers a number of very good men. Some results of their work are summarized in this paper, and it is a pleasure to acknowledge their cheerful spirit of co-operation and the enthusiasm and loyalty with which they have assisted in the building of a geophysical organization to serve the Canadian mining industry HISTORY Geophysical prospecting is commonly, but quite erroneously, regarded as something new. The name is modern, but the principle of applying physical laws to reveal the presence of hidden ore is several hundred years old. Already, at the beginning of our civilization, the need was strongly felt for methods that could indicate the presence of ore in regions where the ore-bodies were completely masked or hidden from the eye. Particularly in countries where the rocks have been eroded during periods of glaciation and later covered by a thick mantle of glacial debris, all kinds of mysterious schemes were invented to locate the hidden ore. Often magic was resorted to (for example, the divining rod), but methods based on sound principles were also developed. Such features as topography, colour and taste of surface waters, and the growth and occurrence of trees and plants, were used to reveal certain types of ore deposits. For finding bodies of iron ore, the compass was very early in use. The fact that objects of iron attract a compass needle was utilized in prospecting long bef01:e the time of Columbus, and a systematic search for bodies of iron ore by this method was organized as early as the year 1600. There are still in existence documents, dated a little over 300 years ago, which show that the Swedish Chancellor of that day, Axel Oxenstiorna, ordered dozens of sun-dial compasses from instrument makers in Germany. The Swedish Government at that time employed a great number of prospectors to search systematically for iron ore. This Government undertaking must have been quite successful, as a number of iron ore-bodies were found in areas covered by heavy overburden. These prospectors were simply Government 'geo-physicists', although they were not known by this fancy name.

Jan 1, 1937

By E. E. Cudby

"FOLLOWING the Leduc discovery •by Imperial Oil in 1947, The California Standard Company began to acquire land in the area immediately west of Edmonton and in line with the Leduc reef trend (Figure 1).The California Standard Winter-burn Province No. 1 in Lsd. 10, Section 4, Township 53, Range 25, West 4th, which was spudded, on the basis of a seismic anomaly, in December, 1949, failed to find reef. This well was located on the eastern .edge of a large land block which California Standard and Imperial Oil had pooled as a joint venture, with California Standard a:s the operator (Figure 2).The culmination •of an extensive exploration and land aquisition programme was the drilling of the California Standard-Acheson Province No. 1 well .in Lsd. 13, Section 2, Township 53, Range 26, West 4th. On August 24th, 1950, a drill stem test was run in the D-3 zone which had been encountered at 4,969 feet, and a flow rate of 702 barrels per day •of 36° gravity oil was obtained. Just previously, Imperial Oil had completed a similar programme in the Stony Plain Reserve with the swabbing-in of Imperial Stony Plain No. 1. These two discoveries set off a drilling programme to determine the extent and value of the oil accumulation.Subsequent drilling of wells some successful .and others not by several other companies as well as California Standard bias, .to date, still left much to be determined as to the approximate delineation of the productive limits of the Ache-son-Stony Plain area. However, to August 31st, 1951, there were twenty-one D-3 producers north of the reserve and three in the Stony Plain Reserve."

Jan 1, 1952

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004