Search Documents

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By G. M. Swinkels

Sherritt Gordon and Cominco, with financial assistance from the Canadian Government through PAIT, have developed a hydrometallurgical process for refining copper from sulphide concentrates. The main objective of the project was to develop a process applicable to a wide range of concentrates with respect to copper content, other metals content and impurities, within the economic parameters set by present smelting and refining practice. Other important objectives were to recover sulphur in its elemental form and not as sulphur dioxide to assure improved hygienic conditions and a negligible impact on the environment. For the most abundant and relatively refractory chalcopyrite concentrates, the first step of the process is thermal activation with hydrogen to decompose chalcopyrite and pyrite, commonly associated with it, into more reactive sulphides more amenable to leaching. The iron is then selectively extracted by sulphuric acid leaching and subsequently rejected as jarosite. High-bornite concentrates do not require thermal activation and acid leaching; they are subjected to another hydrometallurgical iron removal step. The high-grade copper sulphide resulting from iron removal, and containing all of the initial precious metals, is then leached under oxygen pressure to produce elemental sulphur and copper sulphate solution . After suitable solution purification, the copper is recovered by high-current-density electrowinning as wire-grade product. Precious metals remain in the leach residue and are recovered after separation of the gangue materials and elemental sulphur. The laboratory and pre-piloting test work had indicated copper and precious metals recoveries comparable to those achieved in current practice. The process was shown to be suitable for handling relatively low-grade concentrates and, in addition, it was capable of high recoveries of associated zinc, molybdenum, nickel and cobalt in saleable form.

Jan 1, 1978

By F. R. Archibald

Introduction It is the purpose of this paper to review the subject of roasting as preparation of refractory gold ores and concentrates for cyanidation, with particular reference to operations at the mill of Beattie Gold Mines (Que.), Ltd., Duparquet, Quebec. Two earlier papers relating to the Beattie roasting operations are cited as background to the ? present discussion, and more general reference is made to other publications relating? to geology and metallurgy at Beattie. The Beattie roasting plant was built in 1937 as an addition to the existing flotation and cyanidation plant to permit complete processing of the ore at the mine property. Previously, the flotation concentrate had been cyanided, yielding 70 per cent of the gold values, followed by re-flotation of a concentrate from the cyanide residue. This re-floated residue was shipped to a smelter for recovery of gold values unavailable from direct cyanidation. The roasting plant itself is of interest through application in its design of multiple-hearth roasters and a Cottrell plant for separate recovery of dust and arsenic. In the laboratory and plant studies that accompanied development of the plant into a dependable and efficient working unit have been found principles and ideas applicable to other roasting 'problems. Before enlarging on these aspects relating particularly to the Beattie problems and plant, brief consideration is given to roasting in general.

Jan 1, 1949

By Longjiang Li, Song Mao, Zhengyang Qiao, Qin Zhang, Guizhou University, Ling Wang

"After a study on the advantages and disadvantages of flotation column, according to the limitation of ordinary flotation column only is used for a flotation of microgranular minerals, the paper designed a new kind of layered convection coarse particle flotation column.Using a bauxite to test the rationality of the flotation column.The test results show that the new layered convection coarse particle flotation column is feasible.It has certain advantages about coarse particles flotation.INTRODUCTIONFlotation column has many advantages, for example,a simple structure, high efficiency and energy saving, the obvious advantage of fine particles flotation , the index superior and so on. The advantages gradually getting people's recognition. Research of flotation column has been a breakthrough, however, due to it only is used for the flotation of microgranular minerals, and the microgranular mineral particles will lead to a series of problems, and makes the processing cost is increased. Due to increase grinding fineness can save the grinding time and reduce the cost of grinding, also can avoid the disadvantage of fairly granular mineral particles cause a deterioration in the flotation. So it is necessary to research a kind of coarse particle flotation column.After a research on the advantages and disadvantages of flotation column, the authors designed and manufactured a new layered convection coarse particle flotation column, the flotation column both in theory and operation is better than flotation machine.DESIGN OF THE LAYERED CONVECTION COARSE PARTICLE FLOTATION COLUMNAdvantages and Disadvantages of the Traditional Flotation ColumnIn the field of mineral processing, as the increasing proportion of ore that has low grade, fine dissemination size, complex mineral composition characteristics. The limitations of traditional flotation machine is increasing[1],for instance, the high energy consumption, severe wear, inconvenient configuration , large amount of maintenance and so on. Compared with flotation machine, the flotation column with high separation efficiency, low investment and production cost, covers a less area low installation cost, less reagent dosage, more suitable for separation of fine particles and can automatically control, etc[2]. At present, the ore is facing the world energy crisis situation, and becoming increasingly difficult to flotation. So it is important to invent a coarse particle flotation column."

Jan 1, 2016

By W. Hrynewich

"The Central Canada Potash facility, a division of Noranda Metal Industries Limited, is located 3 kilometres south of the junction of Highways 16 and 2, about 75 kilometres south-east of Saskatoon, Saskatchewan. The site occupies 26~ hectares of land and includes well-equipped machine and electrical _shops, a 325,000-tonne muriate storage and reclaim warehouse, a stores warehouse, processing plant (mill), two mine shafts (one for production, the other for servicing and personnel transport), as well as a two track product loading complex. Access to the site is by road and railway (CN and CP Rail). Suppliers of operating and maintenance use both means of transportation, whereas muriate shipments are entirely by railway.Currently five continuous mining machines - one a Goodman 526 borer and four Marietta 911-A units produce some 10,500 tonnes of ore per operating day. A smaller Voest-Alpine Af.1-100 boom type miner is used for floor cutting which was previously done by a production unit. In order to maintain safe, competent ground conditions only 35 percent of the total ore is extracted. At this rate mine reserves are deemed adequate for about 100 years. The plant has operated since August 1969 and has a current practical annual capacity of 1,270,000 tonnes of muriate. As of June 30, 1981, some 11.9 million tonnes of muriate had been produced from 31.4 million tonnes of ore. Of the total muriate, 6.1 million tonnes was granular, 4.8 million was coarse, and 1.0 million was standard. No standard product has been made since August 1978."

Jan 1, 1982

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By J. A. Ressinger

"The purpose of this paper is to discuss some of the differences between various methods of excavating and loading as they relate to mining operations. The intent is not to provide ""pat"" answers, but instead to raise some questions and set forth some reasonable guidelines.Specifically, the paper deals with the differences and relative merits of power shovels versus rubber-tired front-end loaders - or, carrying this further, comparing what could be called ""stationary"" loading or excavating devices to ""mobile"" types."

Jan 1, 1972

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984

By Hans E. Madeisky, Bruce W. Downing

Abstract-The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: anorthosite-hosted magmatic sulfide nickel, dunite-hosted magmatic sulfide nickel, porphyry copper-gold, and volcanic-hosted high sulfidation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray fluorescence equipment, already used for grade control at many mine sites, could provide the wholerock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By R. E. G. Caines, P. Alport

"Operating heavy equipment in Labrador, where the winters are 8 months long and the temperature frequently drops below -40°F (-40°C) for days and sometimes weeks presents unique problems in both the operation and maintenance junctions. Winterization programs must be well designed and implemented at the proper time. These programs must include the proper selection of fuel oil, engine oil, hydraulic oils, greases, cooling system fluids, etc. More often than not, modifications have to be made to the original equipment in order that it can be operated safely and economically in the Canadian North. Manufacturers usually design equipment for a less harsh environment and the user makes adaptations by trial and error.Operators have to be trained for the proper operation on ice- and snow-covered roads in an open-pit mine. Special emphasis must be put on haulage road conditions. In this paper, the authors will cover some specific maintenance procedures, equipment modifications and operator training problems experienced by the Iron Ore Company of Canada in its open-pit operation in Labrador.IntroductionT he Iron Ore Company of Canada is engaged in open-pit mining , concentrating and pelletizing of iron ore. The company operates in two provinces, Quebec and Newfoundland (Fig . 1) . The Knob Lake operation "", based in Schefferville, Quebec, has mine sites located both in Labrador and Quebec . The Caro l Lake Project is situated in Labrador, 25 kilometres east o f the Quebec border at Labrador City. The Carol operation mines, concentrates and pelletizes it s o re before rail transportation to the seaport o f Sept-lies via the Quebec North Shore and Labrador Railway."

Jan 1, 1984

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By R. Drozd

"The Bullmoose Mine is currently under construction in the North East Coal area of British Columbia, and approximately $300 million will be spent to bring this 2.3 million-tonnes-per-year metallurgical and thermal coal mine into production by December 1, 1983.The project is an unincorporated joint venture undertaking, with Teck-Bullmoose Coal Inc., a wholly-owned subsidiary of Teck Corporation, holding 51%, Lornex Mining Corporation holding 39%, and Nissho-Iwai (Canada) Ltd. holding 10%. Bullmoose Operating Corporation will be the manager and operator of the project.This paper will broadly cover the history and exploration work on the property, the geology, open-pit mining plans and equipment, the preparation plant flowsheet from breaker station to clean coal silo, the 35 km highway truck haul, the railroad loadout system, manpower requirements, construction progress, approvals and permits, and general financial arrangements.IntroductionThe Bullmoose Mine Project"" is located about 87 road kilometres south of Chetwynd, B.C. and consists of an open-pit coal mine, a plant facility in the Bullmoose Creek valley below the mine, and a separate rail loadout facility on the British Columbia Railway Branchline near the new town of Tumbler Ridge some 35 road km to the east.The plant will be capable of producing a total of 2.3 million tonnes per year (mty) of washed metallurgical and thermal coal. Long-term metallurgical coal contracts for high quality, medium volatile, bituminous coal have been signed with nine Japanese buyers for 1.7 mty, and the balance of 0.6 mty will be thermal coal production.Plant construction began in the spring of 1982, and in May 1983, preproduction waste and overburden removal in the mine will commence. The plant should be fully operational by December 1983, and first vessel loading at the Ridley Island port is scheduled for January 1984."

Jan 1, 1983

By John M. Gordon

DURING and after 1949, various groups of British mining engineers came to the Dominion Coal Company, Limited, at Sydney, N .S., to see at first hand the Dosco MINER ( 1). These visits culminated in 1952 with the ordering of four Dosco Miners by the (British) National Coal Board on an experimental basis through their Experimental Expenditure Funds. Others are now on order. The first machine was delivered in February, 1953, and, after slight alterations to suit the different power supply, the machine was made ready to work. Due mainly to the size of the machine, new rules and regulations governing its operation had to be put into effect and it was not until April, 1954, that the machine was put underground. It started to produce in June of that year. The three others were delivered early in 1955. The authors were sent to England by the Dominion Coal Company to install and demonstrate these machines and to work with the Coal Board engineers to- further interest in the machines in the British coal fields .

Jan 1, 1956

By James D. Bamburak

Total mineral production in Manitoba has averaged C$1 billion over the past ten years. Industrial mineral production has comprised almost 10% of the total, with more than half coming from the aggregate sector. In southeastern Manitoba, tantalum, spodumene and amblygonite concentrates, cesium and rubidium ores, cesium formate, dimension stone and sphagnum peat moss are produced. Gypsum, high-calcium limestone and lime are produced in the Interlake area. Early industrial mineral production consisted of tools and implements, salt and pottery. Historical production has included: salt, building stone, aggregate, lime and dolime, lignite coal, gypsum, natural and Portland cement, calcium bentonite, brick, light-weight aggregate, caustic soda and soda ash, and silica sand. Future industrial mineral production may come from reactivated quarries, pits and wells or from new producers of current commodities. Newproducts may include: stainless steel master alloy, silicon metal, titanium and magnetite, lithium carbonate, float-plate glass and ferrosilicon, "marble" dimension stone, magnesium metal, potash and kaolin.

Jan 1, 2001

By A. Longval, Q. Jiao, T. Shannon

In 2000, Xstrata Zinc (former Falconbridge Ltd.) Brunswick Smelter commissioned a modified lead blast furnace. Since then, efforts have been made to improve its operation in order to achieve optimal operation in terms of coke consumption, lead loss to slag, and improved environmental and hygiene conditions. This paper will review the important step changes in operational philosophy, undertaken since 2004, for the control of the blast rate, oxygen enrichment in blast, slag chemistry and charge level. Furthermore, a review of the improvements made in secondary materials consumed at the blast furnace will be made. This paper will also discuss the significant reduction of the frequency of accretion removal as a result of improved furnace operation.

Jan 1, 2008

By M. A. Perras, H. A. Kasani, G. Walton

The development of an underground repository for the storage of spent nuclear fuel relies on a multi-barrier system to isolate the used fuel from the environment – ultimately, the biosphere. These barriers include engineered copper and steal canisters, dense bentonite, and the natural rock as well. In order to reduce the potential flow pathway along the excavation induced damage zone, various slots perpendicular to the excavation axis have been proposed. These slots are called cut-off seals and generally are filled with bentonite as it has high swelling potential and very low permeability. Many different geometries have been proposed, but clear guidelines on the selection of the optimum geometry have yet to be developed. In order to assess the optimum geometry, three shapes have been selected for this numerical study, including a trapezoid, a triangle, and a thin rectangular slot. The cut-offs were modelled for a conceptual shaft constructed in the Queenston Formation from Ontario over a stress to strength ratio that has been found at many underground research laboratories. It was found that the excavation of a triangular and thin slot cut-off had the smallest increase in the damage as quantified based on the extensile volumetric strain within the plastic yield zone. Both shapes showed an increase in the damaged zone by 13 cm at a stress to strength ratio of 2.75. The trapezoidal cut-off damage zone increased by 20 cm at the same stress to strength ratio. Further study is required to better define the optimum cut-off shape for wider variety of conditions and other geological formations.

Jan 1, 2020

By G. W. Sparkes

The use of CR-39 plastic polymer as a solid state nuclear track detector in the textural analysis of radioactive minerals in geological samples was first described by I.R Basham in 1981. CR-39 autoradiographs provide a detailed, high-resolution image of the in situ distribution of the radioactive minerals within geological samples on both the macroscopic and microscopic scales. This technique is an inexpensive and effective means of obtaining detailed textural information that provides insight into the style of mineralization, its relationship to primary and secondary structures in the host rock, and its association with particular geological features or mineral phases. Although this technique does not provide any information on the identity of the minerals responsible for the radioactivity, the resultant autoradiographs can be used to select regions for further detailed analysis such as petrography, microprobe analysis, or SEM imaging. This paper summarizes the procedure and outlines the appropriate time and materials required for both the exposure and etching of the CR-39 with respect to the intensity of the radioactivity emitted by the geological samples.

Jan 1, 2013

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By Sherwin F. Kelly

"THE TITLE I have chosen is certainly not one of those self-explanatory ones. I shall endeavour to make its significance clear during my remarks but, in the hope of minimizing that inevitable exodus which follows a good lunch such as this, I am going to withhold the final key to its meaning until the very last sentence of this talk.Some explanation is due at the beginning, however, so for those of you unfamiliar with Spanish I will explain that casa means house, or home. The casa about which I am going to talk necessitates a wide .and generous interpretation of the word, because I am using it to indicate principally that portion of the North American continent which is the home, in the western hemisphere, of British and American ideals of justice and freedom, the dignity of the individual and his right to exercise private initiative .and engage in private enterprise. In a wider sense, I am including the entire western hemisphere, which may yet stand as the last bulwark of political and industrial democracy.As for the treasures of which I am about to speak, may I remind you that there are no• material treasures but those derived from the earth, and they are derived by one of two processes, -mining and farming. These two fundamental industries are the basis, and the sole material basis, of our welfare, our wealth, our very existence. From farming, whether it be farming of the land. or farming of the sea, we obtain the food to keep us alive, healthy and able to work."

Jan 1, 1955