Search Documents

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By M. Krasowska

Dynamics of collision and kinetics of the bubble attachment to hydrophobic solid plates (Teflon) of different surface roughness were investigated. The experiments were carried out in such a way that probability of the collision and probability that the detachment will not occur were equal always 100%. Thus, it was possible to determine effect of the surface roughness on the bubble attachment (three phase contact formation, TPC) only. A high-speed camera (1182 Hz) was used to record the velocity variations, bouncing and time of attachment of the bubble colliding with Teflon plates having different surface roughness (5 different plates). Roughness of the plate surfaces was modified in a mechanical way using different abrasive papers. It was found that the roughness had a crucial influence on the time-scale of the TPC formation and attachment of the bubble colliding with the Teflon plates. Despite high hydrophobicity of all plates (contact angles 1100 -115º) it was observed that at the smoothest surfaces (called "Teflon I" and "Teflon II" and having surface roughness below 1 um) there was no attachment during the bubble first collisions. Prior to the attachment four or more "approach?bouncing" cycles of the colliding bubble were observed there and simultaneously the bubble shape varied rapidly within time intervals below 0.85 ms. Time of contact of the colliding bubble with the Teflon plates was very short; 2-3 ms. These results indicate that during that short time of the collision the liquid layer separating the colliding bubble and the solid surface did not reach a critical thickness of its rupture.

Jan 1, 2006

Who is CIBC? ? Canadian Imperial Bank of Commerce (?CIBC?) is a leading North American financial institution. ? Total Assets: US$315 billion ? Market Capitalization: US$29 billion ? CIBC comprises three strategic business lines: ? CIBC Retail Bank ? CIBC Wealth Management ? CIBC Wholesale Bank ? CIBC Wholesale Bank is a leading North American investment bank with niche capabilities in Asia, Australia & Europe. ? 1,000 + employees around the world ? Product range includes: Mergers & Acquisitions advisory and financing, Equity and Debt issues, Merchant Banking and Strategic Lending ? CIBC is ranked as the #1 investment bank in Canada across most of its key products and industries ? #1 Equity Underwriter in Canada ? #1 Mergers & Acquisitions Advisor in Canada

May 1, 2010

By Peter Waggitt

Northern Australia has been home to uranium mining for over 70 years, more or less continuously. In the early days, post World War 2, there was little effort made to remediate workings at the end of operations. The three “campaigns” of uranium mining (1951-55; 1960-70; and 1979-present) are all now in various stages of remediation. This includes not only the large legacy site at Rum Jungle but also smaller fields like the South Alligator Valley, as well as contemporary works at Nabarlek and the ongoing closure at Ranger– Australia’s longest operating uranium mine. This paper briefly describes some of the past remediation activities before providing an update on the Ranger closure programme and future timetable.

Jan 1, 2020

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By Gilles Tremblay

The legacy of orphaned/abandoned mines, with their associated environmental liability, human health concerns and the financial costs of clean up is a serious issue facing Canada. In 1999 and 2000, a number of stakeholders put forth requests to Mines Ministers to establish a joint industry-government working group, assisted by other stakeholders to review the issue of abandoned mines. The Ministers supported this initiative and asked that a multi-stakeholder workshop be organized to identify key issues and priorities. The Workshop on Abandoned Mines, held June 2001 in Winnipeg, developed consensus, guiding principles and recommendations that were presented at the Mines Ministers? Conference, September 2001. Ministers agreed on the importance of a large-scale program for the rehabilitation of orphaned/abandoned mines sites. A multi-stakeholder Orphaned/Abandoned (O/A) Mines Advisory Committee was formed and a plan was developed to study various issues relating to the implementation of remediation programs across Canada. Three task groups were formed to address the following key areas: Information Gathering; Community Involvement; and Barriers to Collaboration. The presentation will include a summary of the results of the three projects and the future work plan for the program.

Nov 1, 2002

By Rob Assabgui

Presentation Overview ? Stobie Mine Sublevel Cave Background ? Elevated Silica Levels ? Silica Control ? Challenges and Issues ? Conclusions

Oct 1, 2010

By J K. Irwin

The authors discuss the application of drum and friction hoists under modern conditions and give four examples of friction hoists proposed for various applications. The paper concludes with a summary of the advantages and limitations of friction hoists relative to drum hoists. Introduction T H~ introduction of the multiple-rope friction hoist m the late 1940's has complicated the se-lection of the right hoist for a given job. Once such considerations as rope safety factor, drum to rope ratio, hoisting distance, tons per hour and/or service duty have been decided upon, the selection of a drum hoist is relatively simple. We now ask our-selves "which hoist -drum or friction? (See Figure 1 and Figure 2). When a friction hoist is a possibility we are immediately concerned with how many ropes to use, whether to hoist balanced or counter-balanced, whether a friction hoist will be flexible enough for the application and, of course, what the relative costs will be.

Jan 1, 1964

By J. C. Gathje

Newmont acquired the Phoenix Project through the acquisition of Battle Mountain Gold in 2000. Shortly after the acquisition, Newmont Metallurgical Services (NMS) and Nevada Operations began development work on a process to Pressure Oxidize (PDX) precious metal rich copper concentrates from Phoenix using the Lone Tree PDX facilities at Valmy, Nevada. The high precious metals content of the Phoenix concentrate - Au up to -300 g/t and especially Ag, up to -1700 g/t - led Newmont to the development of a High Temperature PDX process that achieves high cyanide leach recovery of Au and Ag, from the PDX solids, without the requirement for a messy and expensive "lime boil" or sulphate destruction process. Base metals content in Phoenix concentrates range from: 15-25 % for Cu, 1-10 % for Zn and 0-2 % for Pb. Excellent solution extraction of Cu and Zn is achieved while Pb is precipitated in the PDX residue. In addition to achieving high Au and Ag recovery this process produces very clean PDX discharge liquors that require minimum effort to remove contaminant metals and PDX solids that have superior settling and filtration characteristics. All of these factors contribute to lower capital and operating costs for the overall process. This paper describes the laboratory and PDX pilot plant developments for this process.

Jan 1, 2004

By Peter Cunningham

Teck Facts and Figures ? Employ more than 14,000 around the world, includes: ? Over 8,600 in Canada (close to 7,800 in British Columbia) ? Close to 2,000 in Chile ? Over 2,700 in Peru ? Approximately 600 in U.S. ? Hundreds more in exploration around the world ? Total capital expenditures ? $1.8 billion for 2012

Aug 1, 2013

By W. H. Zieman

"THIS IS THE THIRD of the consecutive Annual Forums on Grinding that were instituted by Mr. L. E. Djingheuzian in 1957. The first was on the subject of Ball Milling (Transactions, Volume LX, 1957) and the second on The N on-Cataracting Ball Mill (Trans-actions, Volume LXI, 1958). From the discussions at these forums it was evident that one of the most important factors affecting the efficiency of grinding is the shape of the liners. In order to make a study of liners in use, it was •decided to seek the co-operation of operators across the country by sending out questionnaires requesting basic information. Additionally, these operators were urged to set down briefly any pertinent information on the subject acquired through experience and experiments at their own particular plants. A compilation and analysis of these data were to form a basis for discussion at the Forum on Liners at the Annual Meeting in Montreal, April, 1959. The response of the milling fraternity to this solicitation was most gratifying, and clearly indicated the importance attached by the operators to the effect of liner design upon overall grinding performance."

Jan 1, 1959

When underground extractions occur beneath or in close proximity to valleys and other forms of irregular surface topographic features, the observed vertical subsidence at the base of the valley is less than that would be expected in flat terrain, while the valley sides are observed to move inwards towards the centre of the valley. The reduction in subsidence at the bottom of the valley is referred to as upsidence and the convergence of two sides of the valley is termed valley closure. Research coupled with mining experience over the past few decades in Australia has identified valley closure subsidence as being very real and quite significant part of non-conventional subsidence effects, which always have adverse effects on natural features, with risks to water flow and aquatic ecosystems. In this paper, we describe a threedimensional numerical modelling approach to investigate the geomechanical mechanisms which cause the valley closure subsidence behaviour, using distinct element computer package 3DEC. The calibrated models can accurately predict subsidence and horizontal displacements, and they are subsequently extended to specifically study the effect of a series of mining geological and topographical factors on valley closure subsidence phenomenon, by developing a range of hypothetical scenarios. Previous analyses carried out using a two-dimensional numerical modelling technique have identified the potential parameters that affect the valley closure subsidence, which mainly include longwall position, horizontal stresses, valley sloping angle, and valley shape. Further three-dimensional analyses regarding the relationships between the major factors and valley closure subsidence are discussed in this paper. The results have significant implications with regard to both the underlying mechanisms that lead to this nonconventional subsidence behaviour, and how these should be incorporated in future valley closure subsidence prediction and mitigation of its impacts on natural features.

Jan 1, 2015

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By Harold L. Gibson, David H. Watkinson

"Volcanogenic massive sulphide deposits of the Noranda Camp cur throughout the Noranda Shield Volcano but are concentrated and along the margins of the Noranda Cauldron. The deposits are realized along synvolcanic faults that also accommodated subsince and controlled the location of eruptive centres. Deposits within e 3 000 m thick Mine Sequence formed during a period of active volcanism and subsidence coinciding with the onset of two cauldron subsidence cycles. The Noranda Cauldron was a restricted site of 10malously high heat flow and structural permeability that favoured e development of a high-temperature hydrothermal system. Metals may have been derived from leaching of aquifer rocks by convecting a water or directly from a shallow underlying magma chamber, now presented by the Plavrian Pluton, that was at its highest position !thin the crust during cauldron subsidence. The deposits formed rough a combination of sulphide precipitation from exhaled fluid td replacement at and below the seafloor in a manner analogous to ose on the modern seafloor.RESUMESi les dépôts de sulfures massifs volcano gènes du camp minier de ~uyn-Noranda sont présents dans les différentes parties du volcanluclier de Noranda, ils se trouvent concentres toutefois, en plus ·and nombre, sur le pourtour de la caldeira (cauldron) de Noranda. ~s dépôts sont localises le long des failles synvolcaniques qui ont cilite la subsidence et contrôle la position des centres d’éruption.~dépôts situes dans la séquence des mines (3 000 m d’épaisseur) sont formes durant un épisode d' activité volcanique et de subsiden qui coïncide avec l' amorce de deux cycles d' affaissement de la rldera (cauldron) de Noranda. Celle-ci Jut le site exclusif d’unflux : chaleur anormalement élevé et d’une perméabilité d’origine cucturale qui ont favorise le développement d’un système hydrothermal a haute température. Les métaux proviennent soit directement d’une chambre magmatique situee afaible profondeur, so it d’un lessivage des roches de l’aquifère par l’eau de mer circulant par convection. Cette chambre magmatique, représentée maintenant par le pluton de Flavrian, se trouvait à son niveau le plus élevé dans la croute au moment de l’affaissement de la caldeira (cauldron). Les dépôts se sont constitués par un mecanisme combinant remplacement et précipitation de sulfures à partir des fluides exhalatifs, au niveau ou au-dessous du plancher océanique, de la même manière que se forment de nos jours, les dépôts de sulfures massifs au fond des océans."

Jan 1, 1990

By W. Noel O?Brien

Introduction Since 1930 numerous improvements have been made in equipment designed for the mechanical removal of broken ore in underground mining operations. New applications of mechanical equipment, as? well as improvements and adaptations of well established systems, are being made continually. It is the purpose of this paper to discuss present-day equipment for the removal or transfer of broken ore by means of a powered hoist and scraper arrangement. The terms used throughout the paper are those commonly employed in the trade literature and by mining men. The terms slusher hoist, hoist, and scraper hoist are used inter-changeably to mean a machine, powered by compressed air or electricity, with drums for the winding of wire rope. The tail rope, also known as the pull-back rope or return rope, drags the empty scraper toward the tail-sheave, that is, back to the loading point. No attempt is made to cover the entire field of application of scraping methods. Rather it is the? writer's desire to emphasize the fundamental principles of scraping practice and design and to relate them to some modern applications. The available literature on scraping practice has been freely used. together with personal observation and information and advice of practising engineers and representatives of companies manufacturing slushing equipment.

Jan 1, 1951

By G. Wilson

"Satisfactory hydraulic performance of a centrifugal slurry pump is not the only design criterion. If abrasive wear exists the severity of any damage can be reduced and the life of the wearing parts prolonged by selecting the correct pump to suit the conditions of service. This paper is concerned with the design and construction of centrifugal pumps for handling abrasive solids. The wear phenomena due to the slurry being pumped and the materials used to combat abrasive, wear are outlined. The hydraulic design of the impeller and casing and their relationship to wear and the hydraulic radial and axial unbalance are discussed. The prediction of abrasive wear in pumps can not be precise, as many factors are involved - and this is the object of current research."

Jan 1, 1973

By Peter A. Hacquebard

Recent drilling programs have shown that the in-situ coal resources of Nova Scotia are very substantial. The grand totals of the measured, indicated and inferred categories amount to 232 m, 646m and 993 m tons, respectively. This vast quantity of coal occurs essentially in five main fields: Sydney, Mabou, Port Hood, Pictou and Springhill. The largest resources (84% of the total) occur in the submarine area of the Sydney coalfield. With a 65% recovery rate, there are at present 150m tons of proven, recoverable coal in Nova Scotia. At a predicted maximum annual production of 5 m tons, this amount equals a lifespan of 30 years. However, additional drilling, particularly in the Sydney offshore area, holds promise of increasing the recoverable reserve tonnage to at least 350 m tons. This figure may be compared with the 484 m tons production obtained during 191 years of mining (from 1785-1976). The geological appraisal of the remaining coal resources in the five fields mentioned is presented in three-dimensional diagrams, per individual seam and corresponding reserve area. In addition, the submarine extensions of the Sydney and Mabou coalfields are discussed in light of results obtained from off shore oil exploration wells. The terminology and standards of coal resource calculations are pointed out, and the phenomenon of seam splitting and its prediction from geological data is illustrated. The availability in Nova Scotia of either thermal or metallurgical coal is considered in relation to rank and sulphur content. This paper was presented in June 1977 at the 90th Annual Meeting of the Mining Society of Nova Scotia. The coal resource estimates, however, have been updated to include the results obtained with the offshore drilling in the Sydney Coalfield to November 1977.

Jan 1, 1979

Discovery of an economic diamond deposit produces considerable wealth in terms of jobs, royalties, mining investment, and economic spinoffs for residents, including Aboriginal peoples. Diamond mines contribute to the GDP, increased personal income per person and reduced unemployment rates. Is it possible in Alberta?

May 1, 2008

By Mike Johnson, Greg Andrews, Niels Verbaan, David Dreisinger

"The Search Minerals Foxtrot project in Labrador represents a significant Canadian resource of rare earth elements rich in the sought after heavy rare earth elements (19.8% HREE/TREE). A preliminary economic assessment of the project indicated that the project is technically feasible and economically attractive. A variety of metallurgical test programs have been undertaken which have led to significant streamlining and simplification of the process flowsheet. The improved flowsheet should allow Search to reach production earlier and will use conventional processing equipment. The results of these test programs are presented and discussed in this paper INTRODUCTIONSearch Minerals Inc. (Search) is exploring and developing a number of deposits for rare earth element (REE) recovery in Labrador, Canada. The Port Hope Simpson District is in the southeast of Labrador and is highly prospective for heavy and light rare earth elements. The Foxtrot deposit sits within the Port Hope Simpson REE District (Figure 1), which is 70 km long by up to 10 km wide. The infrastructure available at Foxtrot is excellent; a deep-water port, air strip, and road and power infrastructure are pre-existing at St. Lewis. The three communities of Port Hope Simpson, St. Lewis and Mary’s Harbour are in close proximity to the site."

Jan 1, 2016