Search Documents

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By B. R. Hart, S. S. Dimov, J. Fournier

Carbonaceous matter (c-matter) in sulphide ores can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob, gold from a cyanide leach solution. This paper describes a standardized procedure for characterization of c-matter in an ore sample providing detailed information on its composition, maturity and preg-robbing capacity. The procedure utilizes the following complementary analytical techniques in conjunction with several chemical tests and assays: SEM/EDX Raman spectroscopy and TOF-SIMS. Results of the test can be used as a predictive tool to estimate the impact the c-matter will have on the gold recovery process. A comparison between predicted preg-robbing behaviour and cyanidation test results are presented.

Jan 1, 2011

By W. N. Hamilton

"Evaporites abound in the Western Canada sedimentary basin, recurring throughout the stratigraphic column and widely scattered over the basin region. Alberta, situated centrally over the basin, includes many of the evaporites within its borders, but only a few have the right geological conditions to form potential economic deposits of salt or gypsum. These include the Middle Devonian Elk Point Group and related evaporites, Upper Devonian Wabamun Group-Palliser Formation evaporites, and evaporites of the 'Triassic Charlie Lake and Whitehorse formations.Salt deposits underlie almost half of Alberta. The major deposits belong to the Elk Point Group, which includes thick salt units in the Lotsberg, Cold Lake and Prairie Evaporite formations. Another, younger salt deposit in the Wabamun Group has only local distribution. Elk Point salts have a maximum aggregate thickness of 430 m in east-central Alberta. The deposits deepen southwestward across the province, from minimum depths of210 m at Fort McMurray to 1820 m at Edmonton.The thickest, most extensive salt deposits are the upper Lotsberg and Prairie Evaporite salts. Both have excellent development potential. The upper Lotsberg is up to 150 m thick, consists of clear, very coarse crystalline halite with only minor impurities, and has a notable lack of non-salt strata in its succession. Analytical data for the Lotsberg Salt show extraordinary chemical purity. Prairie Evaporite Salt differs lithologically from the Lotsberg in having a significant non-salt component. The deposit is up to 200 m thick and consists of medium crystalline halite, brownish coloured and cloudy as a result of finely dispersed impurities. The main impurities-shale, anhydrite and dolomite-are most prevalent as interbeds in the salt succession, ranging from very thin laminae to beds several metres thick. Although of lesser purity, the Prairie Evaporite Salt is shallower, thicker and more extensive than the Lotsberg and the salt quality is quite acceptable for most industrial uses."

Jan 1, 1982

By Sir Stopford Brunton

Gold was first found in Nova Scotia about 1830-40, but its significance at that time was not appreciated. Probably the first discovery that resulted in any work was made by Lieut. C. !'Estrange, at Mooseland, on the Tangier river, in 1858.1 Since that time gold has been mined with varying success until now, and from 1868 onwards work has never altogether ceased. Gold mining in Nova Scotia is at the moment under a cloud, and the idea generally accepted by most people is that it has failed in the past, and that there is no prospect for it in the future. The actual reasons for the present situation have never been carefully analysed, and it seems a good thing to see what really is the state of the case and whether or not this general idea is worthy of credence. It is the purpose of the present paper to analyse the situation in the light of present knowledge, and to set forth some data which may assist in the future development of the Province.

Jan 1, 1926

By C. Díaz, M. Barati

Prof. Torstein Utigard's untimely death, in the spring of 2012, put an abrupt end to a meritorious career in the field of high temperature chemical process metallurgy. As an academic in the Department of Materials Science and Engineering of the University of Toronto, Torstein made solid contributions to the advancement of knowledge pertaining to production and refining of both nonferrous and light metals, and to the development of inquisitive and innovative young people in extractive metallurgy. In this profile, the authors highlight aspects of Torstein's rich personality and of his contributions to his field of expertise.

Jan 1, 2015

By L. Tejeda, J. R. Donald, R. Parra, J. Duran, P. H. Lauzon

"Crucible slag tests were employed to evaluate different refractory brick classes for the Cerro Matoso electric furnace. Comprehensive analysis was conducted to evaluate the crucible erosion and characterize any slag/refractory reaction products.The classes of refractories investigated were:•,tar-impregnated magnesia;•,rebonded fused grain magnesia-chrome;•,direct bonded magnesia-chrome;•,alumina-chrome;•,picrochromite; and•,magnesia-alumina (spinel).It was concluded that tar-impregnated MgO bricks were the most suitable for the slag chemistry and furnace environment according to corrosion and infiltration resistance. A picrochromite (MgCr2O4) brick performed exceptionally well with regards to erosion resistance, however, the slag infiltrated extensively through the brick pores. Alumina-chrome, direct bonded magnesia-chromite, and spinel (magnesia-alumina) bricks were evaluated as not suitable for use in the furnace."

Jan 1, 1999

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By Jean Dugas, Roger Sirois

The Mineral Deposits Service of the Quebec Department of Natural Resources is engaged in the preparation of metallogenic maps as a contribution to the Canadian Sub-Committee of the Metallogenic Map of North America. The preliminary work is being done on large-scale maps. The main objective is to clearly represent information on ore deposits in a suggestive way. The design of the legend to meet these requirements is discussed. As these maps are still only descriptive, a further step will be the interpretation of data into metallogenic maps with Jess emphasis on the individual deposits and more on the metallogenic factors. Both types of map should prove useful in the search for ore deposits; the first by providing at once a large amount of information, the second by suggesting the ore controls.

Jan 1, 1967

By W. R. Horn

"WHAT I PROPOSE TO DO is to review or report very briefly and generally on the most important subject areas of environmental concern within the mining industry and to indicate the progress being made. First, however, it seems to me both appropriate and necessary to refer to what I said in an address to the CIM Annual Western Meeting, in November 1971, in Vancouver. At that time, I tried to convey: that the awareness and alertness of this far-flung and diversified industry was sharply on the up-swing; that the knowledge of helpful technology for the abatement of pollution by water and solids was significantly increasing; that most mines were doing something about it; that many had already achieved a recycling of process water to a really significant extent; that progress was being made - though not without considerable difficulty - on the large-scale neutralization and subsequent chemical treatment of acid- and metals-bearing waters; that increasing work was being done by individual mining companies on methods for the vegetation of completed tailings impoundments; and that it had been possible to develop a meaningful estimate of the amount of money to be spent by the industry on environmental control measures during the period 1971-75 (as much as $500,- 000,000 ) . Reference was also made at that time to the constructive work in hand toward the fixation, elimination or dispersion of sulphur from smelters and to the considerable attention which was being given by the indust(y itself toward in-plant problems, e.g., dust and noise. Finally, note was taken of the fact that the inclusion of environmental control costs in the pre-operational financial provisions of new mining operations is now established practice."

Jan 1, 1973

By J. G. Mieczaniec

"A key element for a successful mining operation is the grinding circuit. It must be reliable, maintainable and must perform to or above design capacities for 95% of the time. Once chosen and installed major modifications are either prohibitive or very expensive. The selection of mills and drive system is probably the single most important decision made within the concentrator complex.Economic studies revealed that the optimum expansion for Lornex was a 68070 increase in plant throughput. This indicated that the new mill would have to be larger than the existing 32-foot mills.The Lornex ore has a wide range of hardness which has a great influence on mill throughput (Table 1). To smooth out the fluctuations, a blending program ha s always been in effect at the mine, coupled with ball charge control for the primary mills. As can be appreciated, an optimum balance is difficult to achieve. A sudden change to so ft ore with a high ball charge puts the mill into jeopardy with a constant speed drive.The blending philosophy would continue after the expansion, but with the addition o f a second primary crusher, it was envisaged to have the new mill process harder ore to maintain production targets. In theory, the new mill would have a proportionally larger ball charge than the existing mills.This scheme makes the new mill vulnerable for processing so ft ore for a fixed speed mill. Thus, variable speed seemed an attractive option.In early 1979 prominent mill manufacturers were invited to submit proposals for the new mill. Fixed and variable speed mills were to be considered with mill size ranging from 32-foot to 36-foot diameter. The proposals were to include the drive, ball charge, % critical speed, couplings, gears, etc. - the complete package. The recommendations were variable with most manufacturers submitting several alternatives. Recommended mill speed varied from 68% to 78% critical. The concept of variable speed was becoming more attractive, Lornex ultimately decided on a twin DC motor drive system for a 34-foot diameter mill.After start-up it was discovered that best throughput occurred at 78% mill critical speed or top speed of the drive motors. The motor speed range was adjusted upward from 186 to 200 rpm. Today the mills operate at 79% critical or a motor speed o f 193.5 rpm.Clearly the selection of the variable speed mill allowed the flexibility to optimize throughput."

Jan 1, 1985

By Jayne Somers

Methane (CH4) is a potent greenhouse gas, accounting for 15 percent of all global greenhouse gas emissions in 2005. Since methane has a much shorter atmospheric lifetime than carbon dioxide (CO2), reducing methane emissions can achieve considerable climate benefits over the next 25 years. Coal seams often contain significant quantities of methane and CH4 released to the atmosphere from gassy mines during coal extraction is a major source of greenhouse gas emissions. Methane (CH4) emissions from coal mining activities constitute approximately 6% of total global human-related methane emissions. Coal mines around the world have recognized that methane is a clean energy resource that can be captured and used productively. Coal mine methane (CMM) is currently utilized for power generation, natural gas pipeline injection, vehicle fuel, industrial process feed stocks, on-site mine boilers, mine heating, and home heating distribution systems. Upgrading mine degasification systems can often improve gas quality and create favorable project economics. The United States has been a leader in coal mine methane (CMM) recovery and use since the 1990?s. There are now 15 projects at active underground mines in the U.S., as well as 26 abandoned mine methane projects. Recovery and use projects at active underground U.S. mines reduced methane emissions by approximately 49 Billion cubic feet in 2010. In an exciting new development, a ventilation air methane (VAM) mitigation project at the CONSOL McElroy mine in West Virginia was installed by Verdeo. Operational since September 2012, this is the first commercial-scale VAM project in the U.S. and the project will reduce methane emissions by an estimated 920 MMCF/yr. As part of the U.S. Greenhouse Gas Reporting Program, actual data on methane emissions from underground coal mines was collected for the first time in 2011 and reported to U.S. EPA in September 2012. The data collected will help inform stakeholders, particularly the underground coal mining industry, of CMM emission sources on public and private lands. The detailed data will also shed light on the specific sources of methane from active underground coal mines and highlight project opportunities for the U.S. coal industry. The paper will cover U.S. coal mine methane emissions, U.S. CMM utilization and destruction projects, Federal policies and State incentives for CMM capture and utilization. 2011 CMM data from the U.S. Greenhouse Gas Reporting Program Subpart FF will be analyzed and compared with previous U.S. Greenhouse Gas Inventory estimates. Other developments, including the voluntary carbon market, will be discussed.

Aug 1, 2013

By K. L. Boyd

"Can the increasing tonnages of ore and waste mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each stage of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in material handling from the mine to the mill, maximizing operating hours per year.RÉSUMÉ Le recours à des concasseurs plus grands et plus performants suffit-il à gérer l’augmentation du tonnage du minerai et des déchets que l’on extrait de nos jours ? Cet article examine les tous derniers modèles de concassage primaire et de grands concasseurs à cône. Il montre que, pour satisfaire aux exigences de production plus conséquente des exploitations minières existantes et nouvelles, il est important d’optimiser les taux d’utilisation à chacune des étapes du circuit de réduction de la taille des roches, en plus d’utiliser les concasseurs plus grands actuellement disponibles. L’objectif de cet article est d’aider les sociétés d’experts-conseils et les exploitants à sélectionner le meilleur équipement ainsi que des articles fabriqués sur mesure pour la manutention de la mine au concentrateur, en optimisant les heures d’exploitation par année.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications have since become available.The rock size reduction process from the mine to the selected milling process facility has not changed since a person first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages:• stage 1: mining (rock breakage and fragmentation);• stage 2: prescreening (scalping);• stage 3: primary crushing; and• stage 4: fine crushing (secondary, tertiary, and quaternary).Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments play a key role in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2017

By Taisuke Sakakibara, Shinya Suzuki, Tatsuya Kato, Chiharu Tokoro, Kenichi Muto

Surface complexation using a diffuse layer model were constructed for arsenic (As(V)), zinc (Zn(II)) and silicate (Si(IV)) for aluminum hydroxide in the co-precipitation process. From experimental investigations using isotherms, zeta potential measurement and XRD analysis, it was confirmed that co-precipitation involved not only surface complexation but also surface precipitation. However, surface complexation was major mechanism for As(V), Zn(II) and Si(IV) removal under the target removal level of the Japanese effluent standard. In surface complexation modeling, exchange capacity of aluminum hydroxide was determined from specific surface area obtained from experimental measurement and site density obtained from reference. Surface complexation coefficients were determined by fitting the removal property and sorption isotherm obtained from co-precipitation experiments. These parameters were in agreement with the numerical parameters found by Karamalidis and Dzombak (2010) who reported a database of adsorption equilibrium constants for gibbsite. The surface complexation models constructed in this study were applied to neutralization process of an actual AMD treatment. Our model could successfully represent the pH edges for As(V), Zn(II) and Si(IV) in the neutralization of AMD.

Jan 1, 2015

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrates identified gold to be mainly present in the form of a solid solution in pyrite. Gold distribution resulted in a poor extraction yield of 55 % by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction and has led to a gold extraction yield of 94%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and used a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a diaphragm-less electrolysis cell. The extracted gold was recovered via adsorption over silica and the gold depleted brine was treated for impurities removal. This brine was recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Jan 1, 2014

By E. Gaucher, M. St-Amant

"Among the electromagnetic surveys performed by SOQUEM in the last three years, a certain number of the more instructive cases have been chosen to illustrate the theory of electromagnetism by field examples of: (a) The depth penetration of the TURAM as compared to the SLINGRAM (Ronka) method. (b) The limitations of the TURAM as compared to the SLINGRAM method when a conductor dips the wrong way, or when it is small in size. (c) The expression of a shallow-dipping conductor in a SLINGRAM survey. (d) The effect on the SLINGRAM survey of deep ditches or reef structures.(e) A comparison between the CRONE and the SLING-RAM method in the Abitibi clay belt, by means of field and model studies, indicating a usually better signal-to-noise ratio for the SLINGRAM method. From the above and from other experiments, different electromagnetic methods are now being used by SOQUEM, depending on field conditions."

Jan 1, 1970

By A. Christoffersson, T. Nillson-Wullf, H. R. Manouchehri

"Mining industry has been the building blocks for human development through millennia and will continue to play its role in sustainability and meeting society’s needs for raw material. In the way towards sustainability, the next generation of efficient and heavy duty of Sandvik’s crushers, CH860 and CH865, are introduced for efficient crushing. As the secondary, tertiary and/or pebble crusher, these new crushers are designed to over perform in tough mining environment. Featuring higher crushing forces relative to the mantel diameter and 500 kW motor, combined with advanced automation system, i.e., sophisticated HydrosetTM and Automated Setting Regulation (ASRTM), combined with overpressure system with dedicated air supply in dust collar, etc., the new crushers provide higher safety, productivity, and reliability with the same foot-print of conventional cone crushers.Since crushers are more energy efficient than mills it makes sense to effort in fine crushing to save energy and protect environment. That has been the logic behind development and introducing stronger and more efficient crushers by Sandvik. The results on crushing hard iron and gold ores by CH865 have proven its efficiency in fine crushing at a higher productivity, availability and reliability rates through increasing throughput for defined size fraction and extended crushing chamber liner life.Within this paper the performance of the CH865 to deal with two different ores are presented discussed with a glance at how the downstream milling process can be benefited by saving energy and reducing the operation cost. In plant practice, the implementation of the new CH865 provides between 25 and 30% of the crushed ore in the size range of first step milling, i.e., < 2 mm, that offers opportunity for reduction in energy consumption in milling and even changing the process plant configuration by directly forwarded that part to gravity separation. Furthermore, potential of converting the rod mill to ball mill to improve productivity has been considered by plant engineers. Furthermore, some potential applications for such efficient crushers are brought into considerations and discussed. The new developments provide about 30% higher crushing force to efficiently deal with competent ores and pebbles. The CH860 and CH865 crushers are well suited to replace conventional secondary and tertiary crushers respectively; nevertheless, CH865 is virtual option for pebble crushing in SAG and AG milling circuits."

Jan 1, 2016

By Zara Hosseini

?Microseismicity ?Seismic Systems ?Intrinsically Safe and Explosion Proof Seismic System ?Case studies: ?Gas Drainage Optimization ?Fault Identification ?Conclusion Seismic Event ?Occurrences in which energy is released in the rockmass creating a series of seismic waves propagating throughout the rockmass ?Can cause a Fall of Ground or CoalBurst Factors creating Seismicity: ?Mining at Depth ?High stress zones ?Major geological structures ?Mining practices and strategies ?Mining activities i.e. drilling and blasting

Aug 1, 2013

By M. A. Nagle

Various strategic projects were carried out in 2002 to increase the capacity of Teck Cominco&apos;s integrated zinc-lead smelter at the Trail operations site in British Columbia, Canada. The lead smelter treats the iron residue from the zinc plant and optimizes the overall zinc recovery. This paper summarizes two options that were considered to reduce the zinc content in the leaching iron residue. The first option involved increasing the capacity of an existing hot acid leach circuit up to the iron loading constraints of the circuit. The second sought to maximize the hot acid leach capability by separating the ferrite-rich solids, followed by aggressive hot acid leaching (>100°C) and subsequent iron precipitation. Different forms of iron precipitation were reviewed in order to determine the most effective and economical approach. Among these, was a novel high temperature ferrite conversion process. The technical results and selection criteria are presented together with possible ways to integrate the process concepts into the current sulphide leaching plant circuit. The first option was selected for implementation and is currently being operated successfully.

Jan 1, 2006

By James Logan

BC Alkaline CuBC Cu--Au PorphyriesAu Porphyries ?Formed over narrow time interval ~205 Ma ?from silica deficientvsalkali-enriched magmas ?At shallowdepths ?Structuralcontrol ?Cu-Au-Ag, trace Mo ?Oxidized system anhydrite, magnetite ?Multipleintrusions & multiplemineralized centres

May 1, 2006