Search Documents

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By J. W. Baker

"The Kerr-Addison mine is on the northeast shore of Larder Lake in the township of McGarry, District of Timiskaming, Ontario. It lies just south of the highway leading to the town of Kirkland Lake, 25 miles to the west.The property was first staked in the summer of 1906, by a party of prospectors led by a Dr. Reddick of Ottawa. Subsequent assessment work resulted in the erection of a 20-stamp mill in 1908. Gold from this mill was used in the first gold coins to be minted in Canada. The operation did not prove successful, however, and mining was suspended. In 1914 a consider-able amount of underground development was undertaken by the Associated Goldfields Co., without success.In 1936 Kerr-Addison Gold Mines Co. carried out large-scale sampling from four adits driven into the hillside at the mine. Results were not satisfactory, but it was decided to drill one last deep diamond drill hole from surface. The hole cut a wide section of gold ore. With this encouragement, further development outlined a large tonnage of ore, and a 500-ton mill was put into production in May, 1938. In 1939, its first full year, the mine produced 54,480 ounces of gold and 2,732 ounces of silver. By 1955 the mill had been expanded to a rate of 4,549 tons daily, and in this year 427,193 ounces of gold and 23,490 ounces of silver were produced.From 1938 to the end of 1955 the total production, from 17,473,797 tons milled, has been 3,607,462.74 ounces of gold (0.2064 ounces per ton), and 182,278.56 ounces of silver, with a total value of $131,073,037."

Jan 1, 1949

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

By P. W. Jensen

Gold deposits in Interior Alaska are commonly coincident in time and space with reduced, mid-Cretaceous granitoids. The True North deposit of the Fairbanks district is several km from such granitoids, but yields mineralization ages indistinguishable from the Fort Knox granite-hosted deposit. True North, however, resembles sediment-hosted epithermal Au, demonstrating the variability of intrusion-related Au deposits in metamorphic rocks. The True North deposit (14M tons at 1.5 gpt) is hosted within a carbonaceous thrust complex separating eclogite facies from amphibolite facies rocks, located > 5 km from mineralized granite outcrops. The ores contain anomalous Sb, As, and Hg (stibnite is the most common sulfide) with ankerite-sericite alteration in steep NE-striking ?feeder? shears and low angle thrust shears. Nearest hornfelsed rocks are located > 1 km away, and across several high-angle faults. Fluid inclusion data indicates trapping temperatures of ~250C from low-density, low-salinity fluids at P < 0.5 kb. Au was originally present as solid solution in sulfides; minable ores are restricted to the oxidized upper 100 m of the deposit. The considerable differences between this deposit and the temporally equivalent Fort Knox intrusion-hosted deposit indicate no one description adequately characterizes this deposit type.

May 1, 2003

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By M. J. Fairweather

"The development of means to maximize the selectivity between galena and sphalerite in lead zinc ores is extremely important to the lead-zinc industry. Two challenging studies recently undertaken by Cominco will be reviewed. The first required an unusually fine grind to achieve liberation between galena and sphalerite. The second contained partially altered galena which resulted in unusual early activation of sphalerite under normal flotation conditions. Means by which lead and zinc separation were optimized in these two ores will be discussed.There are two important factors in the separation of minerals by froth flotation: particle size distribution (grind) and pulp chemistry. Pulp chemistry includes a number of factors including pH, Eh, collector type and concentration, inorganic depressants, organic depressants and activators.Grind is important for two reasons. A sufficiently fine grind is required to optimize liberation. However, if the mineral dissemination is too fine, mineral selectivity in the flotation process is impaired. Due to the hydrodynamic constraints of conventional mechanical flotation cells, flotation works best over the single decade size range between 10 and 100 microns. The majority of new ores treated by Cominco until relatively recently were comparatively simple. The major factor in their treatment was defining optimum grind size. Accordingly, the focus within mineral processing at Cominco was on grind and supporting liberation studies. The relationships between grind, liberation and flotation response are intuitively easy to understand. An idealized relationship is shown in the first figure."

Jan 1, 1991

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth&apos;s crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming&apos;s management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

By D. E. Calisaya, É. Poulin, A. Desbiens, R. del Villar, A. Riquelme

"A 15 cm diameter by 732 cm height, fully automated pilot column was installed in the Agnico-Eagle’s Laronde concentrator (Québec), for evaluating the performance of newly developed sensors and advanced process control algorithms. For eventual comparison purposes, the pilot column is continuously fed with the same slurry feeding the copper-circuit third cleaner column. It is equipped with electrical conductivity-based sensors for estimating the three variables used in the multi-variable control algorithm under evaluation: froth depth, fraction of wash water underneath the interface and gas hold-up. Froth depth is regulated using a PI controller while a predictive controller is formulated as the minimization of the tracking errors of gas hold-up and bias rate, keeping several operating constraints between their practical upper and lower limits. In particular, an unreachable high set point of gas hold-up can be selected in order to maximize the bubble surface area available for particle collection, while maintaining bias rate above a minimum value required for froth cleaning. The proposed strategy may indirectly help optimizing flotation column operation by using these secondary variables, without the implementation of a real-time optimization layer.INTRODUCTION Flotation columns have already been used for more than 30 years, mainly in cleaning stages, as a result of their froth washing capabilities. Despite their widespread usage, the measurement of some pertaining variables and their use for automatic control is rather scarce. Among the most important variables directly related to the process metallurgy (concentrate grade and recovery), froth depth (hf) is the only one normally monitored and controlled. Even though commercial sensors are available, gas hold-up (eg), a variable directly related to concentrate recovery, is seldom measured and never controlled. Another important variable, bias rate (Jb) responsible for concentrate cleaning, is simply not measured at all, as there is no commercial sensor available. Therefore, besides froth depth, continuous monitoring of process variables is limited to flow rates (gas, feed, tailings, wash water), i.e. to manipulated variables. Some new available sensors have been industrially tested, e.g. the Sonar-TracTM for eg (O'Keefe, Viega & Fernald, 2007) and the McGill hold-up sensor (Tavera & Escudero, 2002). Others, for bias rate and frother concentration, have been successfully validated at laboratory scale by Laval’s LOOP researchers (Maldonado, Desbiens, del Villar & Chirinos, 2008b; Maldonado, Desbiens, del Villar & Aguilera, 2010a). Some devices have been extensively used for monitoring bubble size and space distri-bution, e.g. McGill bubble viewer (Gomez & Finch, 2007) and others."

Jan 1, 2012

By Francis Chachula, Niel Erasmus

"In 2002, Titanium Corporation Inc. focused its attention on the development of a process for the recovery of valuable heavy minerals, including zircon and titanium bearing minerals from oil sands froth treatment tailings. The development of a process flowsheet to recover the titanium and zircon minerals from the Athabasca oil sand tailings has evolved through many laboratory, bench and pilot scale iterations.Initial development work focused on so-called ‘beach sand’ material, which is tailings material deposited over a period of time close to the tailings pipe discharge. The derived process flowsheet primarily consisted of gravity concentration stages, which is typical of all mineral sands operations. Titanium Corporation’s business plan calls for the utilization of tailings directly from the tailings pipeline – the process developed around the beach material is therefore risky as it differs from the live tailings in a number of aspects, with the effects on the process unknown. Titanium Corporation successfully obtained an intermediate product through a ‘bulk sampling plant’ coupled directly to an Oil Sands operator’s froth treatment tailings pipeline, during the summer of 2005. Subsequent further processing of this material resulted in poor separation or concentration of the heavy minerals due to a number of reasons. A more effective process flowsheet had to be developed.The newly derived process is basically a marriage between mineral sands technology and oil sands technology that can economically concentrate and recover the heavy minerals and entails the incorporation of a flotation process that takes advantage of the entrained bitumen in the feed to separate the heavy mineral fraction from the quartz gangue This paper will describe the newly derived process as well as the successful results of a subsequent on-site concentrator pilot campaign completed during the 3rd Quarter of 2006."

Jan 1, 2008

By George H. Hope, Steve Ciccone

"The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day ice-free shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction.INTRODUCTIONThe Red Dog Mine, which began operations in 1989, is located above the Arctic Circle in Northwest Alaska, approximately 145 km north of Kotzebue (Figure 1). An 80-km road connects the mine site to the DeLong Mountain Transportation System (DMTS) port site. Red Dog is the largest known zinc deposit in the world, with known reserves totalling 94.5M tonnes, and is the largest zinc producer with a concentrate production rate of more than 1.1M t/yr.Open-pit mining is by typical drill, blast and load operation using moderately sized mining equipment. Ore is processed through conventional crushing, grinding, and flotation to produce separate lead and zinc concentrates. Filtered zinc and lead concentrates are trucked year-round to the DMTS port site, where they are stored in two A-frame buildings, 330 and 440 m long. A lightering barge system is used to transfer concentrate from the shallow water load-out to deep-sea vessels anchored approximately two miles offshore. Shipping is limited to a 100-day, ice-free window beginning in early July."

Jan 1, 2003

By J. -F. Lessard

Most underground mines rely on ore pass systems to ensure the transport of ore and waste. The design and operation of ore pass systems often rely on past experience, which is often anecdotal and at times contradictory in nature. This paper summarizes the current practice in Quebec underground metaliferous mines. The information was collected during a series of site visits in ten underground mines. The database includes information on ore pass configuration, support, materials transited, and overall ore pass performance.

Jan 1, 2006

By W. R. Leeder

"The Quintette coal property lies in the Rocky Mountain foothills of northeastern British Columbia (see Figure 1). Quintette and the adjacent Bullmoose property of Teck Corporation are soon to become the first commercial coal mines in the Peace River Coal Field, which is estir1ated to contain 10 billion tonnes of metallurgical coal reserves.Denison Mines Limited acquired the original Quintette coal licenses in 1969 and 1970. Exploration began soon after and the first feasibility study was conducted in 1975. Denison devoted the following six years to extensive planning and feasibility studies of the project. During this period, the provincial and federal governments also undertook studies to assess infrastructure requirements and economic viability of development in this part of the province. Many of the proposed mine sites such as Bullmoose and Quintette were at least 100 to 150 kilometres from the towns of Chetwynd and Dawson Creek, the nearest centres serviced by good highways and a railroad, and a complete network of services would have to be provided if such mines were to be developed. The overall project became known as the North East Coal Development.Concurrently with the feasibility studies, numerous technical and sales missions to Japan were made by representatives of Canadian industry and government, culminating in January 1981 with agreements for Quintette Coal Limited and Teck Corporation to supply a total of 115 million tonnes 8 million tonnes per year for 15 years of primarily metallurgical coal to the Japanese Steel Industry."

Jan 1, 1983

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man&apos;s effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By Peter Claus

In the last years, supported gold catalysts with particle sizes smaller than 10 nm have attracted a lot of attention. While gold bulk metal is rather inert in chemical reactions and, thus, is of low interest for catalysis, highly dispersed gold particles supported on oxides as TiO2 or ZrO2 show surprisingly high activities in some reactions important for the chemical industry. The oxidation of carbon monoxide at low temperatures is mainly used as model reaction to study the unusual properties of gold catalysts [1]. On the other hand, to evaluate the catalytic potential of gold, other chemical reactions which allow to control also the selectivity have to be considered. The selective hydrogenation of ???-unsaturated aldehydes to allylic alcohols is of both commercial relevance (e.g. in fine chemical and pharmaceutical intermediate production) and specific scientific interest [2]. Note that thermodynamics favors hydrogenation of the C=C over the C=O group (stronger negative free reaction enthalpy of 35 kJ/mol), and for kinetic reasons the C=C bond is more reactive than the C=O group. Thus, in the presence of most of the conventional hydrogenation catalysts, based on Pt, Rh or Pd, -unsaturated aldehydes such as acrolein and crotonaldehyde are hydrogenated predominantly to the saturated aldehydes and only to a minor extent to unsaturated alcohols. Therefore, it is desirable to find catalysts which are able to control the intramolecular selectivity by hydrogenation preferentially the C=O group while keeping the olefinic double bond intact (Fig. 1).

Oct 1, 2003

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By André van Wageningen

Long term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. In current mining operations, it is important to report changes in long term plans as soon and as accurately as possible. Where geological data can change rapidly, such as in narrow vein deposits, the need to quickly identify and optimize different long term alternatives becomes a difficult task and can lead to many permutations of the long term mine plan. The question arises, is the new plan optimal or not? Can the company objectives be met while adhering to operational constraints? Although a number of optimization techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimization techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the possible permutations. The GA itself contains very little problem specific information and, as such, in this study, has been linked to a discrete-event simulation (DES). The DES is able to evaluate each sequence proposed by the GA and determine the effectiveness and value of each schedule. The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimization process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GADES module is then used to ?optimize? a narrow vein theoretical case study and the results discussed in a broader mining context.

Oct 1, 2004