Search Documents

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By D. B. Stewart

In the past few years, much effort has been spent in elucidating the impact of diesel engines on the mine environment. This paper summarizes diesel fundamentals , exhaust emissions and typical tailpipe concentrations. Mine sampling results and an evaluation of exhaust treatment systems are discussed. A review of changes in pollutant concentrations between the tailpipe and the mine exit is made and suggestions are given to reduce operator exposure to diesel contaminants.

Jan 1, 1978

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

A recovery process for rare earths (REs) such as dysprosium and neodymium from the leach liquor of permanent magnet scrap (PMS) was developed. The two hydrometallurgical routes namely liquid-liquid extraction (solvent extraction) and selective stripping were implemented. The present study deals with the separation and recovery process development by using organo-phosphorous based extractant di-(2-ethylhexyl phosphoric acid (D2EHPA) as reagent for REs processing. Initial studies considered the influence of time on the extraction process, as well as pH and extractant concentration effects. This suggested the aqueous mechanism and separation factors played a role in process during development. McCabe-Thiele diagrams for extraction isotherms were developed. Counter current extraction (CCE) using various phase ratios influenced metals separation. Maximum loading capacity of the D2EHPA was determined. The loaded organic generated by the CCE process was water washed followed by a scrubbing process to remove the other metal ion from targeted metal. Finally, a stripping process was tested using various mineral acids.

Jan 1, 2015

By Greg Yuriy

Over the past two decades, Vale Canada has used discrete-event simulation in a key role to support many underground mining studies. Traditionally, general purpose simulation software was developed for manufacturing and service applications. Not until recently have Mine Designers and Simulation Specialists been able to model the dynamics of underground mining scenarios without extensive manipulation of the inherent tools and entities contained within these simulation environments. This paper discusses Vale Canada?s past experiences with a variety of simulation software, describing model development methods and highlighting some of the lessons learned. The paper concludes with a review of recently considered software and provides a framework of desired attributes/functions for modeling mining scenarios.

Aug 1, 2013

By J. C. Underwood

"The wear performance of grinding balls under conditions of impact and abrasion is affected by their chemical composition and structure. The selection of appropriate analyses and heat treatments that will provide both abrasion and impact resistance takes into account the effects of certain elements on structure and harden-ability, as well as the over-all effect of composition and hardness penetration on the residual stress pattern developed through heat treatment. Direct quenching from forging temperatures substantially increases hardenability over that obtained in reheat-quench practices, and can be done without undue risk of damage to the ball provided that the harden-ability bears the correct relationship to ball diameter.Average volumetric hardness and percent hardened volume are convenient parameters for quantitatively expressing the response to heat treatment and indicating anticipated wear properties. A number of factors which can lead to reduced wear life as a result of material or processing problems are reviewed and illustrated."

Jan 1, 1959

The Industrial Minerals Milling Section of the Mineral Processing Division has been engaged for the past three years in a study of the separation of minerals, by means of electronic sorting equipment, on the basis of their colour. Considerable knowledge of the subject has been built up. Because the object of this study is application as a means of beneficiation, a number of examples of the separations achieved are presented. Introduction T 0 the mineral collector, the colour of a mineral may be pleasing, even fascinating; to the mineralogist, student or professional, it may also be practical. It serves, to some extent, as a distinguishing feature in many minerals, and helps to fix with reasonable accuracy the identity of a few. It may now become a useful tool of the mineral dresser. The idea of using a difference in colour as a means of separation of one mineral from another is not new. Hand sorting dates back to ancient time. However, the means by which this can be done mechanically was developed only during the past decade. As far as the Mineral Processing Division is concerned, interest dates from March, 1960, when the following item was observed in the

Jan 1, 1965

By Malcolm Black

Introduction The circumstances under which the gold mining industry was forced to curtail operations a few years ago are well known to all. The effect of those circumstances is particularly noticeable when one enters some of the larger mills that were designed, in better times, to treat relatively large tonnages. On their grinding floors one will observe that a number of grinding units are lying idle, and the ravages of rust are everywhere in evidence. The same applies to other equipment throughout these mills. In 1941, we found it necessary to reduce tonnage considerably in the Wright-Hargreaves mill. With the assumption that a lower tonnage would be of long duration, we began to focus our attention on some of the idle equipment with a view to re-arrangement of the flow-sheet for greater economy of operation. In an article by the writer published in the Engineering and Mining Journal (March, April, and May issues, 1939) , it was pointed out that in designing this mill there was a very limited floor space available. The choice of thickening equipment was imposed solely by the necessity for space: conservation. Thickening by gravity would have required 5,000 square feet of floor space, whereas Genter thickeners required only 1,200 square feet. As a consequence, the Genters were chosen. The decision to add flotation to the circuit was made primarily to save space. On a cost-plus-tail basis, 80 to 100 hours agitation on all pulp would produce similar overall results, but would require much more space.

Jan 1, 1948

By P. Burke, V. Vuaroqueaux, A. Doyle, C. Petit, Kipouros. G. J.

Magnesium and its alloys are attractive for use in automotive and aerospace applications because of their low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present work reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents results of current work on producing magnesium alloys via powder metallurgy (P/M). P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The surface layer formed on the Mg powders during processing acts as a barrier to diffusion and sintering is problematic. The layer contains oxides, hydroxides and carbonates of magnesium, formed by reactions with the atmosphere. There are several means to possibly overcome this barrier. Alloying additions have been identified that may promote surface layer disruption during sintering. Processing variables such as sintering atmosphere may reduce the layer or allow the formation of less detrimental compounds. Post-sintering processes such as hot working may disrupt the layer and improve density. The experimental effect of all these processing parameters is presented in this paper.

Jan 1, 2010

By F. L. Wu

Based on the analysis of a sealed coal mine resulting from a fire-triggered explosion, limitations were discovered in the re-entry procedures used to reduce the size of the sealed area that were being applied during the process of re-opening the mine. The analysis of two re-opening plans in a mine using mechanical ventilation showed that the estimation of the degree of damage of two air doors close to the working face with the fire was key to the identification of the optimum mine recovery plan. The operation points of airflow and air pressure of the main fan under either the doors? damaged or intact conditions can be estimated through the use of a ventilation network simulation program. Starting the main fan for a short time period and measuring its operation points of airflow and air pressure allowed their comparison with the simulated values. This procedure provided a reasonable estimation of the degree of damage of the ventilation structures and more confidence in choosing a recovery plan. Through this process, it was possible to conclude that the two doors were still intact. Consequently, the final plan of installing a new main fan in the main decline, sealing the initial upcast shaft and unsealing the auxiliary downcast shaft, was proven to be reasonable at the mine site.

Aug 1, 2013

By Iwueze Anaekperechi Rose

The International Labor Organization has declared mandatory adequate provision of safe workplace and safety for all workers in all occupations including the mining sector. Early scientists like Agricola (1559) who studied the health of Miners, found that there are peculiar health problems associated to their work and working environment. This unsafe working condition was one of the major factors that resulted to the Industrial revolution in England and eventually led to the establishment of regulations and laws guiding operations in all workplaces and workers in England and all over the world. Recent studies by Heinrich suggested chains of events of safety issues in the mining sector. Occupational injuries, accidents and ill health have huge social and economic implications on workers, their families and communities. Top mining top issues are respiratory diseases, noise, explosives, ventilation, fire, and explosion. However, one of the principal mechanisms for achieving Occupational Health and Safety (OHS) goals and mapping the future is government regulations of employers. In Nigeria, the situation is not different; mining operations are equally hazardous and have far reaching implications. In 1995 the Ministry for Solid Minerals was established to focus on the development of other categories of mineral products ranging from gold, coal, uranium, and tantalum deposited across the country. Prior to this an Act of Parliament Act Cap 121 of 1946, was in place to regulate amongst other contents mining safety. This was subsequently reviewed following the incidence of Lead poisoning resulting from small scale miners processing gold ore highly contaminated with lead in Zamfara state (northern Nigeria). Hundreds of children died as a result of exposure to lead poisoning, it was clear that the regulations were not sufficient (details to be discussed). However, advances have been achieved in mining engineering since then. A review team was constituted to provide a more stringent law to regulate mining operations in Nigeria. The strategies for mapping the future of OHS in mining engineering will employ amongst others setting and adopting ISO/ILO standards and enforcement; providing technical assistance; and establishing sustainable developmental structures as surveillance and compensation. The management systems approach was also developed as a result of cases of accidents. The accepted international standards guidelines and requirements will be proposed. Furthermore in mapping the future for Mining Engineering, it is suggested that most countries have their own management strategies and legislation to improve safety of workers through greater consistency and efficiency of OHS programs. Some American researchers came up with the Safety Engineering Model. The Australian Mining Council of mineral and petroleum resources after the Catastrophic Maura Disaster developed the National Mine and Safety Framework. In Canada, after the Hillcrest mine disaster in 1914, Allan shaft coal mine catastrophe in 1918, Westray mine explosion in 1992 and other disasters, Occupational Health and Safety Act R.R.O 1990 was sufficiently developed to provide adequate safety conditions and standards. In Nigeria after the disastrous Zamfara lead poisoning, which claimed the lives of hundreds of children due to exposure and lack of appropriate safety measures, stringent measures were developed by the federal ministry of Justice to address and regulate mining process in Nigeria.

Aug 1, 2013

By A. J. Stapleton

"The Copper Mountain mine of Gaspe Copper Mines, Limited was brought into production in January, 1968.This paper describes the organization, scheduling and control of maintenance of large open-pit equipment, including 8-cu.yd shovels and 85-ton electric-wheel haulage units. The facilities for repair as well as maintenance are also described, including repair shops and field repair equipment. Maintenance costs are discussed and particular reference is made to tire inspection, records and costs."

Jan 1, 1969

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By John Convey

This paper, a follow-up to an earlier study, gives the history of Canadian developments in mineral processing from 1921 to the fall of 1964. It deals extensively with comminution and flotation, and then goes on to cover the fields of gravity concentration, magnetic concentration, cyanidation, the processing of uranium ores, and instrumentation. Several outstanding examples of installations are given. The paper concludes with a discussion of present-day trends in mineral processing. Introduction T HE history of the developments in mineral processing in Canada from its earliest times to 1920 has already been published by one of the authors (1). The present paper is thus a logical follow-up to bring this history to date. From 1834 to 1920, mineral processing in Canada, as elsewhere in the world, was in its formative stage. This, however, prepared the ground for developments that have resulted in a mining empire from the Atlantic to the Pacific, a mining empire which could be said to be almost on par with that in the United States.

Jan 1, 1965

"8.1. IntroductionThe stoichiometry of most named platinum-group minerals (POM) is known (cf. Cabri, 1981b, in Chapter 7), but, because these minerals are subject to a wide range of element substitutions, representative analyses require treatment in a separate chapter (section 8.2). The analyses, in all cases done by electron microprobe, are grouped in sections according to the principal platinum-group element (POE) for each POM, and then follow sequentially with increasing amounts of the principal POE starting with the ideal composition, when known. In order to facilitate reference to specific POM by name, an alphabetical listing is also given (Table 8.1). A range of compositions, in addition to one or several ""representative"" analyses, is given for some POM when more than one analysis has been reported for a particular locality. The tables of POM analyses (Tables 8.2 to 8. 76) include at least one analysis for every locality for which data have been published, to the best of the authors' knowledge. All analyses are referenced for locality and publication source, and include several unpublished analyses (all but one done at CANMET). Most analyses have been rounded off to one decimal place for amounts more than one per cent and their formulae calculated on the basis of an even number of total atoms. In all tables, ''n.d.'' stands for elements sought for but not detected and a dash signifies elements not sought, or when these haven't been specificed in the publication source.Section 8.3 contains tabulated analyses and, in some cases, also includes a critical assessment of POE-bearing minerals in which the POE occur in trace or minor quantities. The organization of the data in this section is by mineral groups; e.g., sulphides, sulpharsenides, silicates, etc. Some of these data are also discussed in Chapter 4 by Crocket (1981) and are discussed briefly in Chapter 6 by Crocket and Cabri (1981)."

Jan 1, 1979

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017

By Peter Price

Introduction The Horne mine, the property of Noranda Mines, Limited, has in the last six years become one of Canada's leading gold and copper producers. Since the smelter was blown-in during December, 1927, up to the end of 1933, it has produced approximately 1,200,000 oz. of gold and 35O,OOO,OOO lb. of copper. The property is situated within an area occupied entirely by pre-Cambrian rocks and characterized by the complexity of rock types and structures common in such terrain. But apart from this the mine also presents other features of unusual interest in the size, number, and variety of the ore-bodies, the mineralogical associations, and the rather exceptional values both in gold and copper. It is not surprising, therefore, that a study of the geology of the mine should bring to light many interesting problems. The present paper summarizes, as concisely as possible, the results of such a study. Actually, it is a much abridged version of a more comprehensive and detailed paper completed by the writer a year ago (1), but embodying certain corrections and additional data made possible as a result of further development at the mine and of field work carried out during the summer of 1933. Owing to limitations of space, the paper is, in the main, a presentation of conclusions arrived at in the course of the study. Much of the supporting evidence cited in the thesis referred to has, of necessity, been omitted here.

Jan 1, 1934

By Adam Moore, Ryan Gillespie, Jarrett Quinn, Audrey Walters, Peter Radziszewski

"Vale Long Harbour Processing Plant (LHPP) was designed to process Voisey’s Bay nickel concentrate into finished nickel and associated copper and cobalt products. The plant includes a secondary grinding circuit comprising two Stirred Media Detritors (SMDs) operating in parallel. The ultrafine grinding circuit was designed to process concentrate at a rate of 33 t/h and produce a ground product (P80) of 20 µm to feed the leach circuits. Start-up of the grinding circuit at LHPP was undertaken in December 2014.The objective of this paper will be to describe the design, commissioning, start-up and performance of the secondary grinding circuit with a focus on the two Metso SMD-355-C mills. Following a brief overview of Vale’s LHPP and the SMD technology, the paper will review the design of the SMD secondary grinding circuit from lab tests through to scale-up performance prediction. This will be followed by the results of circuit commissioning outlining some of the issues raised and addressed after which SMD performance will be outlined. Specifically, the SMD circuit grinding performance will be examined since start-up which will include the effect of media size and wear on grinding. Furthermore, impeller wear will be examined by determining initial “shear volume” and worn “shear volume” as well as its effect on mill power and the means to maintain it. The paper closes with a discussion on grinding performance."

Jan 1, 2016

By M. B. B. Research Council of Alberta Crockford

Introduction Kootenay strata of Lower Cretaceous age contain much of the highest rank coal produced in Alberta. These strata outcrop in the foothills and mountains of southwestern Alberta and southeastern British Columbia, and the economic value of the coal seams contained in them was evident to the earliest explorers, who refer co them in their journals. Lacer, investigation of the .coal measures was undertaken by prospectors and by a succession of geologists, most of whom were in the employ of the Federal government, but some acted for private interests. Surveys by these men proved chat foothills and mountain regions hold immense quantities of high-grade coal within easy reach of transportation facilities, and their conclusions have accelerated the development of the coal-mining industry m Alberta. Among geologists who have contributed much to our knowledge of the region are J. M. Dawson, G. M. Dawson, R. C. McConnell, D. B. Dowling, J. D. Mackenzie, B. Rose, J. R. Marshall, B. Rose, J. R. Marshall, B. R. McKay, J. A. Allan, and J. L. Carr. The present paper is to a great extent a compilation of the work of the above men and of several others who have investigated the area lying between Bow river and Crowsnest pass. Space does not permit a list of all the sources of information so chat only chose of prime importance are given in the text. Data for the map and ?cross-sections of Figure 1 were taken from the following published maps of the Geological Survey of Canada: Cascade Coal Basin, Pub. 933; Canmore, Maps 322 and 323; Upper Elk River and Upper Highwood Rivers, Pub. l980; Blairmore, Pub. 1584; Southfork Coal Area Map l03A; and of the Research Council of Alberta: Highwood-Elbow Area, Map 20; and Ribbon Creek Area, Map 21. In some cases, the cross-sections have been simplified or otherwise altered, and for these revisions the writer cakes full responsibility. The stratigraphic sections of Figure 2 have been taken from published reports of the above mentioned organizations. The area covered in this paper is shown in Figure l. It is wholly within Alberta, and reaches from township 5 to township 27 and from range 1 co range 11, west of the fifth meridian. Its location is about fifty miles west of both Calgary and Lethbridge. Topography of the area ranges from foothill on the east to mountainous on the west. In this paper' the foothill region is considered to be chat which lies immediately east of the most easterly mountain ranges, such as Livingstone and Highwood. There are two principal coal mining districts in the area, one served by the main line of the Canadian ?Pacific railway and centring about Canmore, the other by a branch line of che same railway and centring about Bellevue, Blairmore, and Coleman.

Jan 1, 1949

By Matt Manson

Renard?1-10 kimberlite pipes and ?Lynx-Hibou?kimberlite dyke system within ?Foxtrot?property 50/50 JV with SOQUEM, Stornoway operator 2001: Discovery of the Renard kimberlite pipes 2003: Discovery of the Lynx-Hibou kimberlite dykes 2006-2007: Bulk sample program 2008: First 43-101 Resource and Preliminary Assessment 2009/2010: Updated 43-101 Resource

May 1, 2010

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977