Search Documents

By C. E. Baltzer

This is the fourth in a series of coal technology reviews being prepared. in accordance with a recommendation voted by the Coal Division C.I.M. in session at the Jubilee Meeting, Vancouver, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review of Coal Technology for distribution among those concerned in the production and use of coal in Canada. Copies of the first review, which appeared in the November, 1948, BULLETIN, pp. 612-614, of the second review in the June, 1949, BULLETIN, pp. 272-275, and of the third review in April, 1950, BUL-LETIN, pp. 1,9?3-196 (also, respectively, in Transactions, Vol. LI, 1948, pp. 262-264 Vol. LU, 1949, pp. 117-120, and Vol: LIU, 1950, pp. 133-136), were distributed by the Dominion Coal Board and are still available on request. In this review, the first in the series in the field of combustion, development and trends during the period approximately from World War II to the present time are described and therefore the presentation is general. Later reviews will particularize developments in relation to the range of coals available in Canada.-ED. INTRODUCTION THE utilization of coal in heat and power producing equipment has become of paramount importance to the coal industry in maintaining stable and profitable markets. In the past, the chief concern was with mining, transportation, and overall supply problems, but modern conditions demand interest in and knowledge of all phases of the product, from coal in situ to its ultimate disappearance in the form of products of combustion. Even the last mentoined factor has caused complications, as is shown by current widespread activity in the field of smoke abatement

Jan 1, 1951

By H. O. Seigel, J. C. Gingerich, E. O. Köstlin

"To satisfy their continuing need to replenish or expand their ore reserves, mining companies are faced with the dilemma of arriving at a proper balance between the dual avenues of discovery through in-house exploration and of acquisition of properties that are relatively proven or are even in production. The returns from exploration activities may be spectacular, but are unpredictable. The allure of an acquisition lies in its promise of quick and risk-reduced addition to reserves. However, it is historically clear that quantum increments in shareholders’ values have arisen primarily through major exploration discoveries, rather than through major late-stage acquisitions. Late-stage acquisitions can prove highly profitable, sometimes based upon the planned use of superior mining or metallurgical technology, but more often occur as the result of unexpected windfalls. At the other extreme, they can become expensive failures through inadequate due diligence, or unforeseeable factors.Citing numerous case histories and industry statistics, it is concluded that a judicious combination of both exploration activity and the acquisition of prospects is the most advantageous strategy for adding new ore reserves. A skilled exploration staff is essential for success, be it through exploration discoveries or through opportunistic acquisitions, preferably at their early stages. In the future, it is anticipated that there will be fewer opportunities for acquisition because of reduced funding for junior exploration companies, leading to increased competition and higher costs for fewer properties, both in the advanced exploration and mining stages."

Jan 1, 2002

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By J. S. Laskowski

Anisotropic minerals are important constituents of many ores. This group includes both valuable minerals (e.g., molybdenite in Cu-Mo ores) as well as gangue minerals (e.g., talc in platinumbearing sulphide ores in South Africa, graphite in Cu-Ni sulphide ores in Canada, chrysotile in Ni sulphide ores in Australia, and clay minerals in all types of ores). Aqueous suspensions of anisotropic minerals exhibit different properties than suspensions of isotropic minerals. The presence of anisotropic minerals in flotation circuits affects the flotation process.

Jan 1, 2012

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

By J. Tuzo Wilson

Abstract A division of part of the Canadian Shield into provinces believed to represent former mountain belts is attempted, special emphasis- being laid upon radioactive age determinations, the relation of Archaean to Proterozoic rocks, and the structure of the Grenville province. Original data on the distribution of radioactivity within several batholiths and their connection with ore deposits are' presented. The possible growth of continents and a theory which explains the shape and distribution of the world's younger mountain and island areas are discussed and applied to the Canadian Shield in an attempt to explain how the growth and present structure came about. The relation of the major mining camps of northeastern Ontario to fault zones is discussed in the light of this theory. Introduction The valuable symposium issued by this Institute to celebrate its jubilees emphasizes the important role of major faults in determining the location of many ore deposits in the Canadian Shield. Many of these faults are known to extend for long distances. It is therefore widely appreciated that it would be of great value if the pattern, ages, and causes of these faults were better understood. This would be particularly useful if the relations of the major fault systems to petrological and metallogenic provinces and to former mountain belts could be established. Each year the volume of available data, and hence the chance of reaching a fuller solution of this problem, increases. This article is a review of the present situation. It is accordingly based almost wholly upon the work and ideas of others, which are gratefully acknowledged. Naturally, responsibility for the selection and marshalling of the data is the writer's.

Jan 1, 1949

By D. E. G. Maschmeyer

The operation of the pilot plant for the S-C Copper Process during 1976 has provided the basic data for the design of a commercial-scale plant. This paper introduces the commercial aspects of the S-C Copper Process through the presentation of a process flow diagram, a schematic flow diagram and basic design parameters for 75,000 tonnes per year (tpy) copper rod production from chalcopyrite concentrate. Basic operating requirements are outlined and a preliminary estimate of operating and capital costs for a Western Canadian location are summarized. The results have been compared with a modern smelter/electrorefinery to highlight the advantages and disadvantages of these two alternatives and to show why the new S-C Copper Process technology should be of interest to the copper industry.

Jan 1, 1978

By T. Takayama Filho

Votorantim Metais Zinco is a smelting facility which produces SHG zinc, zinc alloys, sulfuric acid, liquid SO2, copper sulfate, cadmium metal and silver concentrate. It is located at Juiz de Fora, Minas Gerais State, Brazil. This facility has been operating since 1980 and its current capacity is 95,000 tonnes of zinc per year, using mostly imported sulfide concentrates.The plant uses the conventional roast-leach electrowinning (RLE) process, in which iron is removed from the circuit as jarosite. The residues generated by the RLE process, which amount to about 200 t/day (dry weight), were until 10 years ago, deposited in tailing ponds having no impervious lining. More recently, jarosite and other wastes have been deposited in a properly built reservoir, but this is reaching its maximum capacity. In order to decommission these disposal operations and to reclaim the sites in an environmentally acceptable manner, Votorantim Metais concluded in 2004 a rehabilitation project for the old tailings pond and prepared detailed plans for managing the current and future disposal of jarosite-bearing residues. This paper describes the procedure for removing iron from the hydrometallurgical circuit and discusses the past and current status of the residue disposal sites, as well as the future challenges related to the environmentally acceptable handling of iron residues.

Jan 1, 2006

By T. Y. Chong, J. A. Folinsbee, M. Fullam

PJV Dome Mine has used some form of gravity concentration since start of milling operation in 1909 to recover free milling gold. Amalgamation and conventional jigs were first used and were replaced with the Knelson Concentrators in 1993. The Knelson concentrates produced were upgraded on a conventional shaking table prior to smelting and refining into gold bullion. In May 2002, a comprehensive review of the latest gravity recovery technology led to a piloting campaign aimed at further improving gravity recovery. The Knelson concentrates, subjected to intensive cyanide leaching in an Acacia pilot plant, were found to be amenable to intensive cyanide leaching with over 98% of the gold being dissolved within 24 hours. An Acacia Intensive Leach Reactor was successfully installed and commissioned in December 2002, to replace the shaking table. his paper describes pilot scale testing, installation, commissioning and optimization of the Acacia Intensive Leach Reactor. Also, the economic impacts on down stream processes are highlighted.

Jan 1, 2005

By B. M. Monaghan

"The developments of the 1950s and 1960s have seen Canada become an international source of iron ore, trading in all geographical areas and hemispheres. Canada's production will significantly increase in the next decade. However, although the outlook is bright, iron ore producers cannot be complacent. Instead, we must weigh the factors that have brought about the development of the Canadian iron ore industry and examine the probable changes for the next decade that will affect its growth.Looking ahead in the 1970s, competition will be severe. Pressure on prices will continue as new sources of supply bid for long-term contracts and as steel producers continue to develop mines around the world. Rising costs will make these pressures more severe. We must balance the growth of the world's steel makers with the emergence of new supplies of iron ore. The iron ore industry is now part of a new era in which demand and supply are intermeshed, and the developments around the world are acting on the Canadian iron ore industry's future."

Jan 1, 1971

By George Rice

Foreword Following the explosion in the Hillcrest mine, which occurred in the evening of Sunday, September 19th, 1926, and in which two men lost their lives, the writer was invited by the Hon. J.E. Brownlee, Premier of Alberta, to conduct an investigation into the causes of the disaster, and to make such recommendations as seemed advisable with a view to minimizing as far as possible the chance of future explosions in this and similar Alberta coal mines. Accordingly, the mine was visited, and extensive investigations were made underground on October 21st, 2.2.nd, and 25th, in company with Mr. John T. Stirling, Chief Inspector of Mines for Alberta, Mr. Moses Johnson, District Inspector for the Crowsnest Pass District, Mr. J as. A. Richards, Inspector of Mines, Edmonton, and also Mr. Thomas Davies, manager, and other officials of the Hillcrest mine. Hearings of the coroner's inquest were also attended on October 20th and 23rd, when testimony regarding the explosion was given by various witnesses. The following paper summarizes my general observations in tracing the place of origin of the explosion, and my efforts to determine the cause of ignition. Certain recommendations arc also made, and the writer invites discussion on these and the other matters dealt with in the paper.

Jan 1, 1928

By Edward Sampson

Bases of National Power At a time when the economy of the world is in a particularly troubled state it is appropriate to examine some problems of the distribution of natural resources. I should like particularly to call attention to the remarkable increasing demand for natural resources, to give an analysis of the demand for certain mineral resources, and to direct attention to some problems in satisfying this demand. All industrial power is based on natural resources and the most basic of these are soils, energy resources, and mineral resources. There is a strong interrelation of these resources, more than is obvious, and I shall take up certain aspects from the point of view of a geologist. Few nations are well endowed with all three of the kinds of natural resources I have mentioned and much has been done by some small countries whose peoples are industrious and enterprising and where conditions for free world trade have been favourable. However, major industrial power is dependent on a substantial endowment of all three classes.

Jan 1, 1949

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By D. G. F. Hedley, F. Grant

"In 1958, the Ontario Department of Mines appointed a committee to study the accident situation and mining methods used in the uranium mines in the E1liot Lake district. This committee reviewed the existing knowledge on mine design, pillar support and roof spans and came to the conclusion that scientific knowledge had not yet reached the stage of producing rational design procedures which would reduce the dependence on trial-and-error methods. Since that time, the Mining Research Centre has made numerous stress measurements in two mines to define the pre-mining and pillar stresses. A comprehensive series of tests has been done in the laboratory to measure the compressive strength of the rock; a geological survey of the region has been made to evaluate tectonic stresses; and a survey was done on mining conditions with regard to stable and unstable pillar configurations. This information has been used to evaluate pillar design as effected by pillar width and height, depth below surface, extraction and pre-mining stress fields. The resultant design of pillar widths and corresponding extraction as the depth increased is in line with past and present experience in these mines. The information available on roof stability is still insufficient to design stable stope spans with the same degree of confidence; experience and trial-and-error methods are still required."

Jan 1, 1972

By A. P. Paiva

The solvent extraction properties exhibited by some /V,N'-tetrasubstituted malonamides to efficiently and selectively recover iron(III) from concentrated chloride leaching solutions can be found in the recent literature. The iron(III) extractive chemistry exhibited by some of these derivatives is revisited, in order to compare their chemistry with that shown by a few of the new malonamide compounds. The generally good extraction efficiency towards Fe(III), from >4 M hydrochloric acid solutions, and the relative ease of Fe(III) stripping by distilled water are remarkable findings that are confirmed for the malonamide derivatives described in this work. Furthermore, additional data regarding their selectivity towards Fe(III) extraction over several base metal ions and their behavior when subjected to successive Fe(III) extraction-stripping tests are also presented and discussed.

Jan 1, 2006

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By Philippe Angers

This article analyzes the social acceptability process of a mining project located in an existing city. It will explore how the principles of sustainable development have been integrated in the project of the Canadian Malartic open pit mine held by the Osisko Mining Corporation, and the corporate social responsibility (CSR) initiatives proposed to strengthen the social acceptability of the project. This mine is located on the ancient south quarter of Malartic and has required the displacement of hundred of houses and five institutions. The location and the inherent social impacts generated by the relocation of the citizens of the south quarter makes this case particularly interesting to understand social dynamics in an era of environmental consciousness. These major constraints of the mine generate high expectations within the urban population with regard to the social and economic benefits it will receive from the project. In a context where society demands higher CSR from the corporation, Osisko is closely followed regarding their actions toward the sustainable development principles to see if they respect the environment and the desires of the community. From the beginning, the company had to be a model of sustainable development in various aspects reflected by the manifold interest of the population. To understand the endeavor made by the company to fulfill the demand of CSR, we will analyze how the company understood sustainable development principles and what CSR initiatives Osisko company put forward. We will explore the involvement of the company in various social aspects like employment, employee satisfaction, and the level of commitment to non-discrimination policy in employment, notably with the native populations. We will also take a closer look at the relationship built by the company with the community and the level of commitment with the various stakeholders of the community. In this way, we will be able to seize the level of involvement of the company in the fulfillment of the principles of sustainable development toward a higher CSR, and to specify the trajectory adopted to build social acceptance.

Aug 1, 2013