Search Documents

Various aspects concerning gold are mentioned below. These have no common theme but suggest points of interest any one of which, if warranted, could lead to development later and elsewhere. 'High level' auriferous gravels The gold deposits of Victoria are commonly classified as being either primary or secondary. Most primary occurrences comprise gold present in quartz reefs, together with other lode-like occurrences in which gold is associated with various sulphides, with or without quartz. Secondary occurrences are derived by physical release of primary gold and subsequent concen- tration of it as a constituent of sediments. Secondary gold deposits may be themselves eroded so leading to third or even fourth generation gold.

Jan 1, 1982

By Koppe J. C, Costa J. F C L

This paper compares different results for overburden volume estimation assisted by geoestatistics, particularly using kriging methods. The main goal is to obtain the most reliable digital terrain model for the calculation of the overburden volume. The data was collected on an irregularly spaced grid and interpolated values were calculated to provide a denser, more regular data set before volume estimation. The field work was developed at the Butia-Leste Coal Mine, southern most Brazil, where an accurate survey was done using a total station theodolite with electronic data collector. The study was developed in five main steps: data acquisition, exploratory data analysis, spatial continuity measurements, point and block kriging estimation and verification of the results. Data acquisition was carried out on a 5 x 5 in grid. This dense grid provides an exhaustive data set of the real terrain against which data subsets can be compared for the various interpolation procedures and volume calculation. This provides an interesting insight into the influence of the number of data on the estimation error. Univariate statistics were used to compare each data subset and the exhaustive dataset. Ordinary kriging on the data subsets followed by contouring was carried out using Geoeas and Surfer software respectively. A subroutine written in C provided the link between the files generated in Geoeas and subsequent contouring routines embedded into the Surfer package. Omnidirectional and directional variograms were modelled defining the parameters for kriging estimation using Geoeas. Different variogram models were checked through cross validation prior to kriging. A comparison between the magnitude of the differences in volumes calculated with the different DTMs was attained. These final result indicates the sensitivity of the volume obtained to the number of data points. As the number of data points increases the estimation error decreases, but at some point there is no significant decrease in the final volume with the collection of additional data.

Jan 1, 1995

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

The overall systems approach to blast furnace aerodynamics is explored including the time and spatial inter-relationships that exist between the furnace lines, tuyeres, burden characteristics, distributor capabilities and furnace operating practice. Attention is called to the time dependent, three dimensional aspects of blast furnace aerodynamics and to the existence of several zones within a furnace where the flow characteristics are different. Changes in furnace operating practice to take further advantage of fully beneficiated burdens including formed coke are discussed from a practical viewpoint. Lessons learned in a variety of shaft furnaces used for other purposes are discussed insofar as they have a bearing on aerodynamics in an iron blast furnace. Questions are raised about the penetration of hot blast in large furnaces. Operating practices and.proposed solutions are evaluated where tuyeres over iron and slag notches are restricted or plugged. Opportunities are presented for using on-line hierarchical computer systems with adaptive tuning algorithms to provide non-linear control of changing process conditions in real time. This will make it possible for the blast furnace operator to optimise a variety of interrelated paramaters, each with different response times. Potential increases in productivity, fuel savings and improved quality control are believed to be within reach.

Jan 1, 1975

By Amanatidis A

In this paper, the kinetics of iron precipitation as sodium jarosite from aqueous solution is investigated. The determination of the reaction mechanism is attempted based on the experimental data of iron removal as a function of time, without using the characteristics of the precipitate.Experiments at the temperature range from 50° to 95°C were carried out with initial conditions of iron concentration IQ g/L, sodium sulphate concentration 25.44 g/L, sulphuric acid concentration 3.68 g/L, pH = 1.5 and agitation rate 600 rpm. Temperature greatly and positively influences iron precipitation from the solution and this is accompanied by pH decrease. The activation energy was determined using the maximum values of the precipitation rate, which were evaluated by polynomial fitting of the sigmoidal shape experimental curves, and it was found to be 44.37 kcallmole. The determination of the rate-controll ing mechanism was based on some criteria used for the discrimination among the three probable mechanisms of precipitation (diffusion, mononuclear nucleation, polynuclear nucleation). These criteria utilise various funetions of the recovery 'a' of iron precipitated versus time, the most important of which are the chronomals. The results of the kinetic analysis procedure showed that the polynuclear nucleation growth mechanism controls the precipitation of iron as sodium jarosite. This was confirmed by the high value of activation energy, excluding diffusion as the controlling mechanism.

Jan 1, 1993

By Garland W

Access to geoscience reference informa- tion including mining and mineral processing has increased considerably in the last five years in Australia. This has been due principally to the use of computer-based information storage and retrieval systems. The main reference data base for the mineral and petroleum industries and disciplines in Australia is the Australian Earth Sciences Information System (AESIS), cooperatively developed and coordinated by the Australian Mineral Foundation (AMF). AESIS is created on the CSIRO computing network (CSIRONET) which has a CYBER 76 host computer located at the CSIRO Division of Computing Research (DCR) at Canberra. Data entry was until recently carried out by AMF using a dedicated line through the Adelaide CSIRONET node to the CYBER 76 interactive system. Data entry is now done directly at the AMF on a DEC PDP 11/44 mini computer that is also a host work station on CSIRONET. Data collection via magnetic tape media input from other computer-based systems is under development. The software used for data entry and management of the data base was developed by CSIRO CILES Systems Development Group. For public interactive online use the AESIS data base is transferred by tape to AUSINET - the Australian information net- work run by ACI Computer Services, Melbourne, where the data base is converted to a form suitable for the IBM STAIRS software. CSIRO facilities at DCR Canberra are used to produce computer type-set camera ready products and output in microform, on magnetic tape or as graphic display. Keywords: Earth sciences information, Computer applications, Information storage and retrieval, AESIS, Data bases, Australia.

Jan 1, 1983

During the past 18 months a rock mechanics project has been in operation at Renison Limited. The project was established to identify and investigate key problem areas that would affect future production at the Renison mine. An in-house approach was adopted, using shall compact equignent, to investigate ground behaviour. Information on the rock stress field was considered to be particularly important for an understanding of ground behaviour. A high horizontal stress component exists, which enables large flat dipping spans of hanging wall to be opened up, with support being provided by post pillars. The amount of support provided by these post pillars has been found to be low.

Jan 1, 1982

Mining software systems have provided a basis for integration of resource, survey, and design functions. They can similarly provide a basis for incorporating ground conditions into the process.Exploration and mine geologists have a prime role to play in this process, extending their responsibilities further across the geological spectrum, into exploration of ground conditions, analyses of results, and assessments of their implications for mining. Ground conditions are as much a part of the geology of a prospect or mine as its mineralisation, and can have critical imnlicationa for mining.

Jan 1, 1993

Robertson Diasol have developed a spectral gamma-gamma tool fully able to withstand borehole conditions. Spectral data is digitally recorded across 256 channels depending on energy levels of the photoelectric effect. Data processing is being developed with the objective of calibrating channel amplitudes to mineral type which will lead to a direct log of selected mineral grade as a continuous trace with depth.

Jan 1, 1990

By Yaniuk DW

The sampling of non-ferrous concentrates from trucks and trains has long been carried out either manually or by automatic spears. Very little use has been made of conventional sampling systems for sampling concentrates at transfer points, or cross-belt samplers for sampling from the belt as the concentrate moves along the conveyor.Due to the high value of base metal concentrates and the often extremely heterogeneous nature of the material it is imperative that the sampling procedures adopted are accurate and precise. The basic principle that all particles in the stream have an equal opportunity to be included in the final sample is not fulfilled by accepted traditional concentrate sampling procedures such as the spearing of wagons, trucks or streams. This may lead to significant bias being introduced into the final sample.Consequently, the application of correct sampling procedures, either with conventional cross-stream samplers or the newer cross-belt samplers, is of prime importance.SGS Australia has recently installed a number of cross-belt samplers for the sampling of base metal concentrates both in Australia and overseas. The application of these samplers will be discussed with emphasis on the benefits of their use.

Jan 1, 1976

By Erceg MM

The Waft River gold deposit is hosted by low grade metasediments which have been intruded by a dacite/andesite porphyry complex. Wafi River is classified as a high sulphur, epithermal type gold deposit having: a high sulphur content, a close association with calc-alkalic igneous rocks, zoned advanced argillic and argillic alteration, and enargite group minerals. Gold occurs as minute inclusions in pyrite and pyrrhotite within intermediate dickite/kaohnite - interlayered illitic clay alteration zones. Central leached silicic, alunite and pyrophyllite zones and peripheral chloritic zones are low in gold. The gold mineralisation at Wafi is interpreted to have been predominantly caused by mixing of hot upwelling acidic magmatic mineralised fluids with cool, neutral meteoric/hydrothermal fluids within permeable sediments. Locallised high grade breccia zones are encountered within the porphyry. An initial resource in excess of I million ounces Au has been defined.

Jan 1, 1990

By Tobin GJ

Testwork carried out in the cooling water circuit at the Yabulu treatment plant of the Greenvale Joint Venturers (Metals Exploration Queensland Pty. Ltd. and Freeport Queensland Nickel Incorporated) since 1980 has resulted in significant improvements to both fouling and corrosion control. At the same time corrosion inhibitor costs have been reduced.Acrylate-type silt dispersants were identified as the most effective means of sediment control in the circuit. An increase in the cathodic component of the corrosion inhibitor coupled with a relatively minor adjustment to water pH has yielded a two to three fold reduction in corrosion rate. It has been established that these lower corrosion rates can be sustained in the face of a 20% reduction in corrosion inhibitor addition rate. Further improvements are indicated with a change of raw water algicide.

Jan 1, 1985

During the last 12 years the dominant theme at Mount Isa has been production expansion. Production rate of 3,200 tons per mine day in 1953 increased to 11,000 tons per mine day in 1960, completing the first stage of the programme. The second stage is still in progress. It is planned to increase production of lead and copper ores to 19,500 tons per mine day in 1968.Current mine workings comprise an area 2 miles long and 1/2 mile wide, the deepest production level being 2,000 ft below surface. During the next 10 years it is anticipated that mining will be carried out to a depthof 3,200 ft below the surface. The rapid extension of the mine has necessitated frequent re-appraisals and modifications to the primary ventilation system, and a system with considerable in-built flexibility has gradually evolved. Since 1953, volume circulation has increased eight-fold to approximately 2,400,000 c.f.m.To suit various mine operating requirements, a combined pressure-exhaust system of ventilation was adopted.The usefulness of this system is at a maximum when the fans installed permit ready changes in the location of the boundary between adjacent spheres of fan influence.Air flow through openings to the surface can be controlled or used as required. This feature is considered necessary for a mine where underground workings are comparatively shallow and caving to the surface willoccur.A major heat problem exists due to climate conditions, high geothermic gradient (one degree Fahrenheit in 95 ft), and oxidation in leached and brecciated areas.Because of this, quantities of air far in excess of the minimum requirements for dust removal are required to ensure satisfactory environmental conditions. In assessing fan pressure, consideration was given to 1. the mine resistance, and the requirement for pressure differential capability,2. the pressure requirement for deeper mining, with due allowance for booster fan use where appropriate,and3. the desire to avoid fan operation at pressure duties above the region of peak fan efficiency.The latter feature provides a safety margin between maximum operating pressure and the stall point of the fan.

Jan 1, 1967

By Lu T. K

A new type of rockbolting system, the self drilling rockbolt, has been studied to develop a 'single pass' bolt for use in rockbolt installation in underground engineering. This single pass bolt forms the basis of a Rapid Face Bolting system which will reduce the amount of time spent in securing a roof during the operation of a continuous miner in the development of a panel.The installation efficiency and anchorage tests were performed in the laboratory on the self drilling bolt and the traditional resin anchorage. bolt. The results of both bolts are cmmnared.

Jan 1, 1993

The use of teleoperation in mining is increasing due to requirements to improve safety and reduce the number of people required to work in remote and difficult environments. We recently completed a project to develop a teleoperated control system for a rock breaker at an iron ore mine in the Pilbara region of Western Australia, with the objective of demonstrating the feasibility of remote rock breaking over long distances. This required controlling both the rock breaker and an array of pan-tilt-zoom (PTZ) cameras using joysticks. Controlling the cameras distracted operators from the primary task of controlling the rock breaker to position and fire the hammer. This lengthened task times as both the operator's attention and their hands have to swap between different control interfaces. In this paper, we present a novel design using human eye gaze as an interactive input for the remote camera control. It follows a simple and natural design principle: Whatever you look at the screen, it goes to the centre. A prototype system has been implemented by integrating computer vision based eye tracking technology, with the advantage of being real-time, robust and marker-less. We conducted a user evaluation, where users undertook a control task while obscuring the direct view of the working area and using a remote camera to transfer the live video stream as the visual feedback. Subjects were required to participate in the experiment using eye tracking camera control and traditional joystick control respectively. The statistical analysis of objective measures indicated that our novel eye tracking control significantly outperformed the joystick control. The results of the post-experimental subjective measures also revealed much higher user preference for using eye tracking control, which provides clear evidence that this design is a better interface for remote camera control in mining teleoperation settings.

May 1, 2010

By Thomas G. A

THE irregularity of the Mount Morgan (Queensland) ore body presents problems other than those only of mining. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and fromhighly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from many stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore, yet it is never safe to take this for granted, and constant assaying is necessary. At the same time the ore merges from one class into...

Jan 1, 1911

Since early 1968 the Bureau of Mineral Resources (B.M.R.) has carried out VLF-EM test surveys in various parts of Australia and Papua. The aim of the work, primarily, was to examine the effect- iveness of the method as an exploration tool under a variety of Australian conditions. Selection of test areas was determined by the availability of geological, geophysical and drilling information and by the desirability to include a variety of physical variables such as depth of weathering and topography. The aim of the present account is to review the results of this work and to make an assessment of the method available to the mining industry. The author wishes to acknowledge considerable assistance both by way of data and discussion provided by Messrs. Paul Gillespie (B.M.R.). and John Haigh (formerly B.M.R., now Senior Geophysicist, McPhar Geophysics Australia.) The article is presented with permission from the Director, B.M.R.

Jan 1, 1971

By Ward C. W

Conventional polygonal and block modelling techniques inadequately represent the grade-thickness distribution of some narrow shear and stratabound gold deposits. The polygonal influence of high-grade drill intercepts can result in overestimates of resource tonnages at high-grade cut-offs. Although block modelling methods provide grade smoothing and a better representation of structural continuity, the technique can lack precise definition of ore width. An alternative method known as Spatial Object Modelling (SOM) has been developed on MineMap software to overcome some of these modelling issues. This method does not rely on a uniform cell size and allows grade smoothing between resource intercepts in three-dimensional space. The SOM technique creates grade-thickness bars on regular, user-defined spacings which allow easy visual comparison of raw intercept data to the interpolated model. Model cell values are readily transformed into isopachs, isopleths and resource perimeters for reporting and mine planning purposes.

Jan 1, 1997

By Golab K, Partridge AC, Fletcher CAJ, Holtham P

Spiral concentrators are used globally in the fine coal processing industry to segregate particles, by gravitation, on the basis of density and size. Consisting of an open trough that twists vertically downwards about a central axis, a slurry mix of particles and water is fed to the top of the concentrator. Particles are then separated radially as they gravitate downward. Since their introduction to Australia in the 1940's, the generic design has evolved largely by laboratory trial-and-error investigations of different prototypes. However, this approach has proven expensive and optimal designs have not been necessarily developed. Accordingly, Computational Fluid Dynamics (CFD) analysis has been used recently as an alternative method of investigation, to assume as is envisaged, a role in the design process. To date, CFD models have progressed to simulations of turbulent fluid flow on current production spiral designs, and are continuing to be adapted for inclusion of particles at realistic feed concentrations. To be able to use the models confidently however, laboratory experiments must also be performed to validate the predictions during the development stage. This paper reports the current findings of an ongoing CFD and experimental program applied to one spiral unit. Satisfactory quantitative agreement has been achieved for the fluid and particulate flow characteristics, and although further validations are appropriate, the model already possesses significant potential for use as a reliable predictive design tool.

Jan 1, 1998

The large rotary blast hole drills for hole sizes of 250 to 375 mm in diameter have been utilized by large open pit metal and coal mines for production drilling all over the world. The design of such rotary drills is in most cases about two decades old and it has not been done much in order to apply a modern technology on rotary drilling. The most modern large rotary drill, Tamrock RI 10, consists of an advantageous rotary head with a squirrel cage AC motor controlled by a frequency converter, a beneficial mast structure with a possibility for inclined drilling, hydraulic driven, independent crawlers, and a modern ergonomic cabin to provide a comfortable working condition for the oper- ator. Several automatic features are available as options. The rig has been designed to be operated by one man only. With this modern rig the produc- tion rate can be increased and production cost kept on a low level.

Jan 1, 1989