Search Documents

By B Ellis

Brunswick Mine is one of the largest underground zinc/lead mines in Canada, producing 3.4 million tones of ore annually. As mining activities advance to deeper levels, ground pressure also becomes greater. To cope with the highly stressed ground, the mine has taken some strategic measures to ensure the targeted production level. Such measures include the implementation of a pastefill system and transferring the mining method from primary/secondary stoping to pillarless pyramid stoping. With the pillarless mining method, stope sizes become smaller and the number of active stopes is also less than before. In addition, mining sequence and cycle time have to be strictly followed according to production schedule. The blasting project described in this paper tackles one of the steps in the mining cycle aimed at shortening the blasting cycle time in a stope. Furthermore, this project was conducted and managed with the Six Sigma initiative in Noranda which was implemented in the fall of 1999. Like a typical process review, the blasting operation was examined by breaking it down into many steps that can be quantified and measured. Each activity was then correlated with different factors associated with blast design as well as blast operations underground. It was found that the utilisation of voids plays a key role in the blasting cycle time. With improved void utilisation ratio, blasting cycle time has been reduced from an average of 12 shifts to ten shifts per stope. This improvement translates into approximately 180 000 tonnes of ore being blasted without any increase in manpower. This paper presents the technical aspects of the study, as well as some operational issues and improvements made during the project.

Jan 1, 2001

By M Fahey, A B. Fourie

Over the past ten years, the mining industry has witnessed the introduction of a new and innovative mine filling technique known as paste fill, which consists of placing full stream tailings with small amounts of binder and water into underground stopes. Paste fill has benefits over traditional backfill methods, such as higher solids contents than hydraulic fill and easier transportation than rock fill. From a geotechnical perspective, the behaviour of very fine material in a fully saturated state can be complex, particularly when binder is added. Previously, there has been no rigorous solution to understanding the paste fill deposition process, resulting in uncertainty regarding critical aspects such as barricade load calculations. This uncertainty has the obvious consequences of potential barricade failures (including at least 12 over the past four years), and for many operations attempts to deal with this uncertainty has led to excessively conservative filling schedules, restricting production. This paper presents an application of Minefill-2D, the first rigorous model capable of representing the paste fill deposition process. The model couples the processes of material accretion, consolidation and cement hydration to calculate the distribution of stress around a stope (including the total stress applied to barricade structures) during filling. Minefill-2D is a finite element numerical program, which has been verified using laboratory element tests, centrifuge tests and in situ measurements (Helinski, 2008). The authors present a sensitivity analysis, carried out using the model, to demonstrate some of the critical and less critical aspects relating to paste backfill deposition. The results of this sensitivity analysis are used to devise a fill management strategy that can be utilised to minimise the risk of barricade failures and maximise fill rates where appropriate.

Jan 1, 2008

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By I Manege, S M. Bennett

The PT Kaltim Prima Coal (KPC) operation is a large scale coalmine operating on the east coast of Kalimantan (Borneo), Indonesia. Originally developed under a coal contract of work (CCOW) with the Indonesian Government, new legislation has led to uncertainty as to the actual life of the mine, the size of the operating lease or mining area, the rehabilitation compliance requirements and other areas of concern. The actual life-of-mine (LOM) plan is therefore in a constant state of flux and must be updated and modified with every new piece of information.Under the CCOW system, the mine life ran from the first year of production (1992) for 30 years (2021), with the potential to extend for a further two ten-year periods. KPC has always intended to run until at least 2041. Under the new legislation, the potential term of the CCOW (to be replaced by a mining license) is open to interpretation, resulting in KPC having to prepare plans allowing for a LOM that may end in 2021, 2031, 2041 or a range of other possible periods of time.Uncertainty about legislation (and hence the mine life) possible production rates and available work areas; variable coal prices and costs; varying management contexts; the substantial reserves available; difficulty sourcing dump space; potential rehabilitation costs and the dependence of a community of over 100 000 people on a single operation sees the LOM and mine closure teams preparing dynamic yet thoroughly robust plans that are updated on multiple occasions per year.This paper will describe the procedure followed by KPC and the potentially show stopping issues that must be dealt with.CITATION:Bennett, S M and Manege, I, ?2014. Life-of-mine planning in a dynamic environment, in Proceedings Life-of-Mine 2014 , pp 379–388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By K Friese, H P÷llmann

Clinoptilolites, modified with sodium, produced a material which has been tested for the ability to remove Hg (II) from aqueous nitric acid. The amount of adsorption depends on contact time, acid concentration of aqueous solution and initial mercury concentration. The study of the kinetics of mercury uptake revealed that all sorbents exhibit a fast rate of sorption. The highest sorption capacities were observed for sodium forms, and were up to five times higher than for the unmodified zeolite. The maximum sorption capacity toward mercury is determined as 0.093 ¦g/g at an initial concentration of 10.0 ¦g/L for a clinoptilolite from Tsagaantsav deposit (Mongolia). The sorption of Hg (II) has an ion-exchange nature and consists of three stages, ie the adsorption on the surface of microcrystals, the inversion stage and the ion exchange in the interior of the microcrystal. Sorption capacity decreases with the increase of mercury concentration. The presence of other metal ions such as Cd (II), Cu (II), Ni (II) and Zn (II) increases Hg (II) uptake capacity. Finally, sorption for Hg (II) was investigated in batch systems to evaluate the short-term stability of the sorption properties.

Jan 1, 2008

Mining is still a significant economic activity within the Hauraki District. The Martha project is particularly significant. Estimates are that in the order of 850 direct and indirect jobs are derived as a consequence of the Martha project within the Waikato Region. The Resource Management Act 1991 (RMA) is New Zealand's primary piece of environmental legislation. It sets out to provide the framework for the control of the use, development and protection of almost all physical and natural resources. Minerals are excluded from the sustainability requirements of the legislation but as mining invariably involves the use of land, all the other elements of RMA apply. The Council's role in dealing with mining changed with the introduction of RMA. It became responsible for administration of those matters that fell within the functions set out in section 31 of the RMA in respect to existing authorisations. Mineral development needed to be considered in the development of the District Plan that the Council is required to prepare. Implementation of the Act has been a challenge for not only local government but for many industries and resource users since it came into force in 1991. There have been, and are, differing views on both the way it is administered and its intent. The Hauraki District Council has been at the forefront of some of the challenges that are a consequence of the Act. Its reactions to these challenges have been consistent. It treats mining in the same why it treats any other industry. At times this approach has not been understood and without challenge from sections of the community.

Jan 1, 2000

By Glasson K. R

The history of Ore Reserve classification and reporting in Australia is largely a history of the Australian mining industry itself. In the late 1800s, when the industry was dominated by small scale, high grade underground mines, Reserves (if estimated) were based on hand sampling and geological inference, and reporting of Reserves was either non-existent or of extremely variable quality. By the mid-20th century, the industry was dominated by large underground base metal and gold mines. Reserve estimation was coming under the control of skilled geologists and mining engineers, however Reserve classification and reporting standards continued to vary in type and quality from mine to mine. Today, large scale, low grade mining operations predominate, and Reserve estimates are generally based on extensive drilling results processed (with geological control) by computer. Through the efforts of a Joint Committee established by The Australasian Institute of Mining and Metallurgy and Australian Mining Industry Council, Reserve and Resource classification and public reporting has been standardised and controlled by adoption of the ""Australasian Code for the Reporting of Identified Mineral Resources and Ore Reserves"" released in 1989. The Code, which will continue to be modified and improved by the Joint Committee, has also been used as a basis for guides to reporting in other countries, and there is now some hope that this difficult and vexing topic may finally become subject to international standards and controls.

Jan 1, 1992

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

By R L. Koenig

Previous papers at Metplant conferences have covered the options for crushing and grinding circuit selection. High Pressure Grinding Rolls (HPGR) may have considerable advantages over autogenous milling circuits but test work and evaluating different grinding circuits must be done to establish which circuit provides the best option. The Hawsons low grade magnetite project provides a specific example in using thorough test work, careful simulations and detail in design to allow the evaluation of grinding circuit performance. Fortunately tools are available for this evaluation and the test work for the Hawsons iron ore is detailed in this paper. The results of the test work and simulation indicates that although the Hawsons iron ore is competent in terms of autogenous milling given the medium hardness of the ore in the Drop Tests, the HPGR testing indicates that the use of HPGR is likely to use half the energy requirement. This is a characteristic of the Hawsons iron ore and is likely to be valid for other iron ores in the Braemer Iron Formation which stretches from the Hawsons lease in New South Wales to Razor Back and South Dam in South Australia. The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. However, the Pilbara region was discovered in this era and this led to development of high grade direct shipping grade hematite ores. Carpentaria Exploration (Capex) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. The magnetite grade was found to be low at around 16% Davis Tube mass recovery (DTR) but despite this, the project provides a positive business case as a result of the following key factors:• The mineralisation is particularly soft for crushing and grinding with a Bond Work Index of 6.3.• The mineralised rock fractures easily preferentially along grain boundaries.• The location is close to mining infrastructure and a skilled workforce in Broken Hill, 60km to the North East.• It is close to road and rail infrastructure for access to the resource.• The only contaminant in concentrate is silica.• The resource contains many billions of tonnes of magnetite mineralisation.The low Bond Work index is a key characteristic of the Hawsons iron ore and the use of autogenous milling and HPGR circuits is compared to other iron ores indicating why the plant energy requirement may be just as important as iron ore grades.

Aug 8, 2011

By S Chaudari, T Ren, T Harvey

Management of respirable dust on longwall face remains a challenging issue for mine operators, particularly for the new generation of thick seam longwalls. A fundamental understanding of the airflow behaviour around the shearer is critical for dealing with the dust control issue on longwall faces. Computational fluid dynamics (CFD) modelling techniques have been used in this study to conduct a detailed investigation of the air and respirable dust flow patterns around the longwall shearer. Three CFD models have been developed to represent different longwall cutting heights. The results of these modelling studies tallied well with field measured airflow data from different mines. The validated thick seam longwall face model was then used for detailed parametric studies to simulate the effect of various parameters and dust control concepts. The dust control options investigated include various spray configurations, shearer clearer, modified cutting sequences and shearer scrubbers of various capacities to minimise the respirable dust migration towards the walkway area of the longwall face. This paper presents a summary of the results of these CFD modelling investigations.

Jan 1, 2005

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021

By A E Reschke

The high-shear colloidal mixer is generally recognised as the most efficient method of mixing cement based grouts. Only recently however has this technology been applied to the production of cemented rockfill (CRF) for use in underground mines in North America. Traditionally, paddle type mixers have been used to produce the cement based slurries required for the preparation of CRF. While considerable success has been achieved with these mixers, tremendous advantages are attained with the colloidal mixer. The combined effect of the highly efficient mixing action and the ability to mix low water/solids ratios, allows for reductions in the cement content for a given strength requirement. Cement can also be replaced by cheaper fillers such as flyash, resulting in further cost savings. Although large-scale dedicated CRF hatching plants are typical, there is a growing need for mobile plants capable of operating anywhere underground. The compact size and rapid hatching speed of high-shear colloidal mixers has allowed them to be incorporated into skid mounted systems capable of producing and discharging cement based slurries onto rockfill aggregate for the production of CRF. In many cases run-of-mine development waste can be used as CRF aggregate with these slurry plants thereby reducing the cost of waste rock removal. These relatively low cost portable plants have now allowed several mines to economically rccmer isolated pillars and realise positive returns on their investment.

Jan 1, 1998

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

By J G Bastias

It is sometimes necessary to resort to extremes in order to call attention to something that is pertinent to safety in mining. When some of the experts in occupational safety talk about this topic, they usually refer to a 'regulation' established by the Romans which stated that, due to the health hazards, usually death, no Romans but only slaves should work in mining. Since the time of the Roman Empire, a lot of ground has been covered in the field of mine safety. Nowadays, it can be said that occupational safety is being seriously addressed, with the result that the number of mining accidents has reduced dramatically, fatalities in this industry are less frequent, and the rate of accidents compared with other activities, such as construction or fanning, is low. This achievement has been possible initially through government legislation and by procedures established by the mining companies themselves. However, the dilemma for government is whether to regulate and if so, how much. It is pleasing to observe that most companies are establishing working procedures which conform with new government legislation, placing strong emphasis on the duty of care for mine employees. There will always be some regulatory aspects of legislation, and perhaps the best example of this is in the use of mine hoists where there are no international or Australian standards, and the regulations applied are of an empirical nature that err on the side of safety.

Jan 1, 1994

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Sixty years after its inception, after an alternation of periods of admiration and rejection by the industry, Sampling Theory can now be seen as going through its golden age. A brief history of its successive transformations and progresses achieved by its author, Pierre Gy, and his followers, reveals the theoretical as well as practical difficulties that had to be vanquished to reach this point. Its current level of acceptance and corresponding trends are discussed and illustrated, with an insight on its increasing real role in the industry and future prospects for its further development.

Jan 1, 2008

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

By E Mroczek, M Climo, B Carey, M P. Simpson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The composition and volume of geothermal fluids in New Zealand offers considerable potential for the extraction of various metals and minerals, as well as being a source of heat energy, steam and gases, and for use in generating electricity. While extracting products from geothermal fluids is technically feasible, positive economics is the key driver for commercial success; however, there is no assessment of this opportunity that identifies simple, cost-effective processing technologies and provides a greater understanding of the economic viability and barriers for implementing such technologies. The methodology that will be used to evaluate the commercial opportunities for New Zealand is discussed.CITATION:Mroczek, E, Simpson, M P, Climo, M and Carey, B, 2015. From waste to wealth – mineral extraction from geothermal brines, in Proceedings PACRIM 2015 Congress, pp 133–138 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Beck, E Jones

The measurement and management of deformation in underground excavations is a key responsibility of geotechnical and mining engineers. A critical aspect of these roles is to ensure there is sufficient ground support capacity for the expected demand.Current methodologies for monitoring deformation and ground support serviceability-limits require measuring displacement at distinct points, or using visual observations. These current methods limit the assessment to a qualitative interpretation of deformation across the entire excavation.Recent advancements of Light Detection and Ranging (LiDar) technology permit a new method for monitoring deformation that allow a full 3D image of extended sections of an excavation to be precisely scanned. The results from the comparison with subsequent scans provide valuable information on the magnitude, direction and extent of regions exceeding the ground support serviceability-limits. This new method now provides a quantitative assessment across the entire excavation being monitored.The implementation of regular scanning has been demonstrated to be highly advantageous not only at mines with swelling or squeezing ground, but also at mines with rapid seismic induced deformation. The use of LiDar technology as a routine deformation measurement tool for geotechnical and mining engineers (and further applications) are discussed in more detail in this paper.CITATION:Jones, E and Beck, D, 2017. The use of 3D laser scanning for deformation monitoring in underground mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017